RedMax BC250 manual Stopping Engine, OP5 OP6, Adjusting Idling Speed OP5, Line Head Usage

Page 28

English

8. Operation

■STOPPING ENGINE

1.Release the throttle lever and run the engine for a half minute.

2.Shift the ignition switch to the STOP position.

OP5

(1)

OP6

NOTE

•Except for an emergency, avoid stopping the engine while pulling the throttle lever.

■ADJUSTING IDLING SPEED (OP5)

1.When the engine tends stop frequently at idling mode, turn the adjusting screw clockwise.

2.When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter- clockwise.

(1) Idle adjustment screw

NOTE

•Warm up the engine before adjusting the idling speed.

■LINE HEAD USAGE

WARNING

1.Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury.

2.Keep the debris guard attached in place at all times when the unit is operated.

TRIMMING GRASS AND WEEDS

•Always remember that the TIP of the line does cutting. You will achieve better results by not crowding the line into the cutting area. Allow the unit to trim at its own pace.

1.Hold the unit so the head is off the ground and is tilted about 20 degrees toward the sweep direction. (OP6)

2.You can avoid thrown debris by sweeping from your left to the right.

3.Use a slow, deliberate action to cut heavy growth. The rate of cutting motion will depend on the material being cut. Heavy growth will require slower action than will light growth.

4.Never swing the unit so hard as you are in danger of losing your balance or control of the unit.

5.Try to control the cutting motion with the hip rather

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents BC250 Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Parts location SpecificationsBC250 Fiche technique Emplacement des pieces Situación de las piezasEspecificaciohes Position Symbols on the machineEmission Control Posición EmplacementControl DE Emisiones Working Condition For safe operationWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoDE LA Machine Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineArranque DEL Motor Demarrage DU MoteurUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI QUELQU’UN S’APPROCHE EntretienSI Alguien SE Aproxima MantenimientoRefill after cooling the engine Handling FuelTransportation Manipulation DU Carburant TransportManipulación DEL Combustible Llenar una vez que el motor se haya enfriadoSet up SE1 SE2 SE3 Installing HandleInstalling Debris Guard Installing Cutting Head SE3Assemblage Montaje Mise EN Place DE LA PoigneeMise EN Place DU Cache ANTI-PROJECTION Instalación DEL MangoFuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Ignition switch Stop Start 4 Throttle set button OperationOP1 OP2 OP3 OP4 Starting Engine Cutting head will start rotating upon the engine startsFonctionnement Uso Levier du starter 2 a Fermé OuvertInterrupteur d’allumage 2 Arrêt Marche 4 Manette des gazAdjusting Idling Speed OP5 Stopping EngineOP5 OP6 Line Head UsageReglage DU Ralenti OP5 Utilisation DE LA Tete DE Coupe a FILCoupe DE Gazon OU D’HERBES Ajuste DE LA Velocidad DE Ralentí OP5Adjusting the Line Length Ajustement DE LA Longueur DU FIL DE Coupe Ajuste DE LA Longitud DE LíneaMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoFor safety reasons, do not use metalreinforced line MA1 MA2Refilling Trimming Line MA1 AIR FilterEntretien Mantenimiento Filtre a AIRFiltre à air Filtro DE AireReplacement Plug is a NGK BPMR7A MA3 MA4MA5 Fuel FilterLE Type DE Bougie DE Remplacement EST UNE NGK BPMR7A Bougie D’ALLUMAGE BujíaCouple DE Serrage SilencieuxMA6 MA7 Spark Arrester Spark arresterGear Case MA7 Intake AIR Cooling VentGrille D’ARRET D’ETINCELLES ApagachispasBoitier DE Renvoi D’ANGLE MA7 Caja DE Engranajes MA7 Ouïe DE Refroidissement PAR AIRMA9 Procedures to be Performed After Every 100 Hours of USE StorageDisposal Cylinder fin Intake air cooling vent backProcedures a Effectuer Toutes LES Heures D’UTILISATION Rangement AlmacenamientoMise au rebut Eliminación Procedimientos Para Desarrollar Tras Cada 100 Horas DE USO12. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes BC250 NotaDrive Unit BC250 S/N 40400101 and up Pipe Engine Unit BC250 S/N KU40001 and up Front Housing Limited Warranty Garantie limitée Garantía Limitada Page Zenoah AMERICA, INC

BC250 specifications

The RedMax BC250 is a top-of-the-line brush cutter that delivers exceptional performance for both professional landscapers and avid gardeners. Designed for efficiency, it combines power and versatility, making it an essential tool for tackling even the most challenging of jobs.

One of the standout features of the RedMax BC250 is its powerful engine. Equipped with a 25.4cc two-stroke engine, it boasts impressive torque and speed, ensuring that it can cut through dense vegetation with ease. The engine is designed for reduced emissions and improved fuel efficiency, adhering to modern environmental standards while still delivering robust power.

User comfort is a critical consideration in the design of the BC250. It features a lightweight frame, which minimizes fatigue during extended use. The ergonomic design includes adjustable handles that allow the operator to customize their grip for maximum control and comfort. This focus on user-friendly design helps ensure that tasks can be completed efficiently, even over long periods.

Another notable characteristic of the BC250 is its dual-line cutting head. This feature allows for a wider cutting path, significantly reducing the time required to clear large areas of grass and brush. The automatic line feed system ensures that the lines are replenished with each rotation, minimizing interruptions during operation and enhancing productivity.

The BC250 also incorporates RedMax’s innovative anti-vibration technology. This system is designed to reduce the vibrations transmitted to the user, which not only increases comfort but also minimizes the risk of long-term hand and arm injuries often associated with operating power tools.

In terms of maintenance, the BC250 is equipped with a tool-less air filter and spark plug access, making routine maintenance straightforward and accessible. This ease of maintenance ensures that the cutting equipment remains in top condition, prolonging its lifespan and reliability on the job.

RedMax is known for its quality and reliability, and the BC250 is no exception. Whether you are trimming grass along sidewalks or clearing stubborn underbrush, the RedMax BC250 combines power, comfort, and advanced technology to ensure optimal performance. For those seeking a reliable brush cutter that meets the demands of tough outdoor tasks, the BC250 stands out as a premier choice in the market.
Top Page Image Contents