RedMax BC250 manual Troubleshooting guide, Guide de localisation des pannes

Page 42

12. Troubleshooting guide

English

Case 1. Starting failure

CHECK

PROBABLE CAUSES

ACTION

fuel tank

incorrect fuel

fuel filter

fuel filter is clogged

carburetor adjustment screw

out of normal range

sparking (no spark)

spark plug is fouled/wet

 

plug gap is incorrect

spark plug

disconnected

drain it and with correct fuel

clean

adjust to normal range

clean/dry

correct (GAP: 0.6 – 0.7 mm)

retighten

Case 2. Engine starts but does not keep running/Hard re-starting.

CHECK

PROBABLE CAUSES

ACTION

fuel tank

incorrect fuel or staled fuel

carburetor adjustment screw

out of normal range

muffler,cylinder (exhaust port)

carbon is built-up

air cleaner

clogged with dust

cylinder fin, fan cover

clogged with dust

drain it and with correct fuel

adjust to normal range

wipe away

wash

clean

When your unit seems to need further service, please consult with our service shop in your area.

12. Guide de localisation des pannes

 

 

Français

 

 

 

 

 

 

1er cas : Défaut de démarrage

 

 

 

 

 

 

 

 

VERIFICATION

CAUSES PROBABLES

ACTION

réservoir de carburant

carburant incorrect

vidanger et remplacer le carburant

filtre à carburant

filtre à carburant colmaté

nettoyer

vis de réglage de carburateur

déréglé

refaire le réglage

allumage

bougie sale ou noyée

nettoyer ou sécher

 

Jeu d’électrodes incorrect

régler le jeu (de 0,6 à 0,7 mm)

Bougie d’allumage

débrancher

resserrer

 

2ème cas : Le moteur démarre mais ne reste pas en marche ou est difficile à redémarrer

 

 

 

 

 

VERIFICATION

 

CAUSES PROBABLES

 

ACTION

réservoir de carburant

carburant incorrect

vidanger et remplacer le carburant

vis de réglage de carburateur

déréglé

refaire le réglage

silencieux, cylindre

dépôt de calamine

retirer

filtre à air

colmaté de poussière

nettoyer

ailette de cylindre/flasque de ventilateur

colmaté de poussière

nettoyer

Si la machine nécessite des opérations d’entretien plus élaborées, contacter le centre de service après-vente le plus proche.

12. Guía de localización y solución de problemas

 

Español

 

 

 

 

Caso 1. El motor no arranca

 

 

 

 

 

 

COMPROBAR

POSIBLES CAUSAS

ACCIÓN

Tanque de combustible Filtro de combustible Tornillo de ajuste del carburador Explosión (no hay chispa)

Bujía

Combustible incorrecto

El filtro de combustible está obstruido.

Fuera del margen normal

La bujía está sucia/mojada.

La distancia interelectródica es incorrecta

Desconectada

Vaciar y llenar con el combustible correcto

Limpiar

Ajustar al margen normal

Limpiar/secar

Corregir (DISTANCIA INTERELECTRÓDICA: 0,6 – 0,7 mm)

Reajustarlo

Caso 2. El motor arranca pero no se mantiene en marcha./Dificultad para volver a arrancar el motor.

COMPROBAR

POSIBLES CAUSAS

ACCIÓN

Tanque de combustible

Combustible incorrecto

Tornillo de ajuste del carburador

Fuera del margen normal.

Silenciador, cilindro (lumbrera de escape)

Acumulación de carbón

Filtro de aire

Obstruido con polvo

Aletas del cilindro, cubierta de ventilador

Obstruidas con polvo

Vaciar y llenar con el combustible correcto.

Ajustar al margen normal.

Quitar

Lavar

Limpiar

Si le parece que la unidad necesita otros servicios, consulte nuestro centro de servicio en su área.

42

Image 42
Contents BC250 Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Specifications Parts locationBC250 Emplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes Symbols on the machine PositionEmission Control Emplacement PosiciónControl DE Emisiones For safe operation Working ConditionWorking Circumstance Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail PrecaucionesWorking Plan Before Starting the EngineDE LA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineDemarrage DU Moteur Arranque DEL MotorUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien MantenimientoHandling Fuel Refill after cooling the engineTransportation Manipulación DEL Combustible Manipulation DU CarburantTransport Llenar una vez que el motor se haya enfriadoInstalling Debris Guard Set upSE1 SE2 SE3 Installing Handle Installing Cutting Head SE3Mise EN Place DU Cache ANTI-PROJECTION Assemblage MontajeMise EN Place DE LA Poignee Instalación DEL MangoWhen using RedMax/ZENOAH genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Lors de l’utilisation de la véritable huile RedMax/ZENOAH Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitFor Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda OP1 OP2 OP3 OP4 Starting Engine Ignition switch Stop Start 4 Throttle set buttonOperation Cutting head will start rotating upon the engine startsInterrupteur d’allumage 2 Arrêt Fonctionnement UsoLevier du starter 2 a Fermé Ouvert Marche 4 Manette des gazOP5 OP6 Adjusting Idling Speed OP5Stopping Engine Line Head UsageCoupe DE Gazon OU D’HERBES Reglage DU Ralenti OP5Utilisation DE LA Tete DE Coupe a FIL Ajuste DE LA Velocidad DE Ralentí OP5Adjusting the Line Length Ajustement DE LA Longueur DU FIL DE Coupe Ajuste DE LA Longitud DE LíneaMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoRefilling Trimming Line MA1 For safety reasons, do not use metalreinforced lineMA1 MA2 AIR FilterFiltre à air Entretien MantenimientoFiltre a AIR Filtro DE AireMA5 Replacement Plug is a NGK BPMR7AMA3 MA4 Fuel FilterCouple DE Serrage LE Type DE Bougie DE Remplacement EST UNE NGK BPMR7ABougie D’ALLUMAGE Bujía SilencieuxGear Case MA7 MA6 MA7 Spark ArresterSpark arrester Intake AIR Cooling VentBoitier DE Renvoi D’ANGLE MA7 Caja DE Engranajes MA7 Grille D’ARRET D’ETINCELLESApagachispas Ouïe DE Refroidissement PAR AIRDisposal MA9 Procedures to be Performed After Every 100 Hours of USEStorage Cylinder fin Intake air cooling vent backMise au rebut Eliminación Procedures a Effectuer Toutes LES Heures D’UTILISATIONRangement Almacenamiento Procedimientos Para Desarrollar Tras Cada 100 Horas DE USOTroubleshooting guide 12. Guía de localización y solución de problemasGuide de localisation des pannes BC250 NotaDrive Unit BC250 S/N 40400101 and up Pipe Engine Unit BC250 S/N KU40001 and up Front Housing Limited Warranty Garantie limitée Garantía Limitada Page Zenoah AMERICA, INC

BC250 specifications

The RedMax BC250 is a top-of-the-line brush cutter that delivers exceptional performance for both professional landscapers and avid gardeners. Designed for efficiency, it combines power and versatility, making it an essential tool for tackling even the most challenging of jobs.

One of the standout features of the RedMax BC250 is its powerful engine. Equipped with a 25.4cc two-stroke engine, it boasts impressive torque and speed, ensuring that it can cut through dense vegetation with ease. The engine is designed for reduced emissions and improved fuel efficiency, adhering to modern environmental standards while still delivering robust power.

User comfort is a critical consideration in the design of the BC250. It features a lightweight frame, which minimizes fatigue during extended use. The ergonomic design includes adjustable handles that allow the operator to customize their grip for maximum control and comfort. This focus on user-friendly design helps ensure that tasks can be completed efficiently, even over long periods.

Another notable characteristic of the BC250 is its dual-line cutting head. This feature allows for a wider cutting path, significantly reducing the time required to clear large areas of grass and brush. The automatic line feed system ensures that the lines are replenished with each rotation, minimizing interruptions during operation and enhancing productivity.

The BC250 also incorporates RedMax’s innovative anti-vibration technology. This system is designed to reduce the vibrations transmitted to the user, which not only increases comfort but also minimizes the risk of long-term hand and arm injuries often associated with operating power tools.

In terms of maintenance, the BC250 is equipped with a tool-less air filter and spark plug access, making routine maintenance straightforward and accessible. This ease of maintenance ensures that the cutting equipment remains in top condition, prolonging its lifespan and reliability on the job.

RedMax is known for its quality and reliability, and the BC250 is no exception. Whether you are trimming grass along sidewalks or clearing stubborn underbrush, the RedMax BC250 combines power, comfort, and advanced technology to ensure optimal performance. For those seeking a reliable brush cutter that meets the demands of tough outdoor tasks, the BC250 stands out as a premier choice in the market.