RedMax BC250 manual MA1 MA2, Refilling Trimming Line MA1, AIR Filter, Air filter

Page 34

MA1

MA2

(1)

English

9. Maintenance

■REFILLING TRIMMING LINE (MA1)

1.For replacement line, use a diameter of .095in (2.4mm). The spool is capable for a line upto 20ft (6m) on the 4” head. Avoid using a larger line as it may cut down the trimming performance.

WARNING

For safety reasons, do not use metalreinforced line.

2.Pinch the slotted area on the both sides of the spool housing to unhook the bottom cap.

3.Take out the spool and pull off the old line. Fold new line so that one half line is 4.7in.(12cm) shorter than another half. And then, hook bended end in the slot of the spool.

4.Wind up the line in the correct direction as indicated on the spool.

5.Hook each end of the line in the slot on the edge of the spool, and then put the ends through the eyelets on the housing. Make sure that the spring and the washers are in place.

6.While holding the spool against the housing, pull the line ends to release them from the slot.

7.Line up the slot on the bottom cap with the hook on the housing, press the cap against the housing until it clicks.

WARNING

•Make sure that the engine has stopped and is cool before performing any service to the brushcutter. Contact with moving cutting head or hot muffler may result in a personal injury.

■AIR FILTER

•The air filter, if clogged, will reduce the engine performance. Monthly check and clean the filter element in warm, soapy water as required. Dry completely before installing. If the element is broken or shrunk, replace with a new one. (MA2)

(1) Air filter

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents BC250 Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Parts location SpecificationsBC250 Fiche technique Emplacement des pieces Situación de las piezasEspecificaciohes Position Symbols on the machineEmission Control Posición EmplacementControl DE Emisiones Working Condition For safe operationWorking Circumstance Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail PrecaucionesWorking Plan Before Starting the EngineDE LA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineArranque DEL Motor Demarrage DU MoteurUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien MantenimientoRefill after cooling the engine Handling FuelTransportation Manipulación DEL Combustible Manipulation DU CarburantTransport Llenar una vez que el motor se haya enfriadoInstalling Debris Guard Set upSE1 SE2 SE3 Installing Handle Installing Cutting Head SE3Mise EN Place DU Cache ANTI-PROJECTION Assemblage MontajeMise EN Place DE LA Poignee Instalación DEL MangoFuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Lors de l’utilisation de la véritable huile RedMax/ZENOAH Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda OP1 OP2 OP3 OP4 Starting Engine Ignition switch Stop Start 4 Throttle set buttonOperation Cutting head will start rotating upon the engine startsInterrupteur d’allumage 2 Arrêt Fonctionnement UsoLevier du starter 2 a Fermé Ouvert Marche 4 Manette des gazOP5 OP6 Adjusting Idling Speed OP5Stopping Engine Line Head UsageCoupe DE Gazon OU D’HERBES Reglage DU Ralenti OP5Utilisation DE LA Tete DE Coupe a FIL Ajuste DE LA Velocidad DE Ralentí OP5Adjusting the Line Length Ajustement DE LA Longueur DU FIL DE Coupe Ajuste DE LA Longitud DE LíneaMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoRefilling Trimming Line MA1 For safety reasons, do not use metalreinforced lineMA1 MA2 AIR FilterFiltre à air Entretien MantenimientoFiltre a AIR Filtro DE AireMA5 Replacement Plug is a NGK BPMR7AMA3 MA4 Fuel FilterCouple DE Serrage LE Type DE Bougie DE Remplacement EST UNE NGK BPMR7ABougie D’ALLUMAGE Bujía SilencieuxGear Case MA7 MA6 MA7 Spark ArresterSpark arrester Intake AIR Cooling VentBoitier DE Renvoi D’ANGLE MA7 Caja DE Engranajes MA7 Grille D’ARRET D’ETINCELLESApagachispas Ouïe DE Refroidissement PAR AIRDisposal MA9 Procedures to be Performed After Every 100 Hours of USEStorage Cylinder fin Intake air cooling vent backMise au rebut Eliminación Procedures a Effectuer Toutes LES Heures D’UTILISATIONRangement Almacenamiento Procedimientos Para Desarrollar Tras Cada 100 Horas DE USO12. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes BC250 NotaDrive Unit BC250 S/N 40400101 and up Pipe Engine Unit BC250 S/N KU40001 and up Front Housing Limited Warranty Garantie limitée Garantía Limitada Page Zenoah AMERICA, INC

BC250 specifications

The RedMax BC250 is a top-of-the-line brush cutter that delivers exceptional performance for both professional landscapers and avid gardeners. Designed for efficiency, it combines power and versatility, making it an essential tool for tackling even the most challenging of jobs.

One of the standout features of the RedMax BC250 is its powerful engine. Equipped with a 25.4cc two-stroke engine, it boasts impressive torque and speed, ensuring that it can cut through dense vegetation with ease. The engine is designed for reduced emissions and improved fuel efficiency, adhering to modern environmental standards while still delivering robust power.

User comfort is a critical consideration in the design of the BC250. It features a lightweight frame, which minimizes fatigue during extended use. The ergonomic design includes adjustable handles that allow the operator to customize their grip for maximum control and comfort. This focus on user-friendly design helps ensure that tasks can be completed efficiently, even over long periods.

Another notable characteristic of the BC250 is its dual-line cutting head. This feature allows for a wider cutting path, significantly reducing the time required to clear large areas of grass and brush. The automatic line feed system ensures that the lines are replenished with each rotation, minimizing interruptions during operation and enhancing productivity.

The BC250 also incorporates RedMax’s innovative anti-vibration technology. This system is designed to reduce the vibrations transmitted to the user, which not only increases comfort but also minimizes the risk of long-term hand and arm injuries often associated with operating power tools.

In terms of maintenance, the BC250 is equipped with a tool-less air filter and spark plug access, making routine maintenance straightforward and accessible. This ease of maintenance ensures that the cutting equipment remains in top condition, prolonging its lifespan and reliability on the job.

RedMax is known for its quality and reliability, and the BC250 is no exception. Whether you are trimming grass along sidewalks or clearing stubborn underbrush, the RedMax BC250 combines power, comfort, and advanced technology to ensure optimal performance. For those seeking a reliable brush cutter that meets the demands of tough outdoor tasks, the BC250 stands out as a premier choice in the market.
Top Page Image Contents