Points in Operation and HOW to Stop, Stopping

POINTS IN OPERATION AND HOW TO STOP

Follow the applicable accident prevention regulations.

Starting

Move at least 3 m away from the place of refueling. Place the machine on a flat, bare surface so that the cutting blade does not contact the surface of ground or any other objects.

Cold start

For machine with U Handle or Loop Handle

-Move the switch (1) to the “I” position.

-Push gently the primer pump (A) 8 to 10 times.

-Set the choke lever (B) to the “CHOKE” position (C).

Note : Depress the trigger safety lock (E) before squeezing trigger.

-Squeeze the trigger (F) to full throttle position and hold it, and then set the switch (1) to the “START” position and release the trigger (F).

-Pull the starter until the engine tries to run (No more than 6 pulls ).

-Set the choke lever to half choke position.

-Pull the starter until the engine start running.

After the engine runs for 30 to 45 seconds at the “START” position ( for warming up the engine ), move the choke lever to the “RUN” position ( D ).

Warm Start ( Re-starting Engine )

- Set the choke lever (B) to the “RUN” position (D).

Note : You do not need to pull the trigger or set the throttle-lock when the engine is warm.

- Pull the starter rope until the engine runs.

STOPPING

Release the trigger (F) fully, and push the switch (1) to the “O” position that the engine will stop.

Be aware that the cutting blade may not stop immediately and allow it to slow down fully.

IDLE SPEED ADJUSTMENT

Your MAKITA engine has been adjusted at the factory for optimum performance and fuel consumption, and no fur- ther adjustment is required.

Due to varying atmospheric and climatic conditions, however, you may need some minor adjustment for your area.

Checking the idle-speed

The idle-speed should be set to 2,800 – 3,300 rpm. If necessary, adjust the idle-speed using with a tachometer to insure the proper idle-speed. Note that the cutting blade or the nylon cutting head must not turn when the engine is on idle.

Adjusting the idle rpm. Can be done by turning the idle-speed screw (A) clockwise ( for increasing the engine speed ) or counterclockwise ( for decreasing the engine speed ).

If the engine does not idle properly after the adjustment, contact your nearest Makita dealer for service.

RE-SHARPENING THE CUTTING TOOL

CAUTION :

The cutting blades mentioned below should only be re-sharpened by an authorized facility. Manual re-sharpening will result in imbalances of the blade causing abnormal vibrations and damage to the machine.

- Cutter Blade : star blade ( 4 teeth ), eddy blade ( 8 teeth )

An expert service for re-sharpening and balancing is provided by Authorized Service Agents.

NOTE :

To increase the service life of the above cutter blade, it may be turned over once until both cutting edges have become blunt.

BCM2610, BCM2600, BCM2310, BCM3300, BCM3310 specifications

The Makita BCM3310 is a top-tier cordless lawn mower designed for efficiency and user convenience, catering to homeowners who value both performance and ease of use. This model exemplifies the robust engineering and innovative technologies that Makita is renowned for, making it a standout choice in the competitive garden equipment market.

One of the key features of the BCM3310 is its powerful 36V brushless motor, which delivers exceptional cutting performance while ensuring energy efficiency. The brushless design minimizes wear and tear, significantly extending the tool's lifespan and reducing maintenance needs. This motor enables the mower to tackle various grass types and conditions, providing a clean and precise cut.

The BCM3310 features a cutting width of 18 inches, allowing users to cover larger areas swiftly while retaining maneuverability in tighter spaces. Its adjustable cutting height, ranging from 1 to 3 inches, enables users to customize the mower’s performance according to their lawn's specific needs, whether it's a neatly manicured appearance or a more natural look.

Another notable attribute of this mower is its lightweight design, which weighs approximately 31 pounds. This makes it easy to handle and maneuver, even for those with limited strength or physical capability. The comfortable grip handle ensures that users can operate the BCM3310 with ease, reducing fatigue during longer mowing sessions.

The BCM3310 is also equipped with a significant 5.0Ah lithium-ion battery that provides longer run times and quicker charging compared to traditional batteries. Additionally, it is compatible with Makita's extensive 18V and 36V battery systems, allowing users to interchange batteries across different tools, enhancing convenience and minimizing costs.

This mower incorporates advanced safety features, including a blade brake that swiftly stops the blades when the user releases the control lever. This ensures added safety for users, especially in cases where they need to quickly disengage the mower.

Furthermore, the BCM3310’s design emphasizes user-friendly operation, with a foldable handle for easy storage and transportation. Its compact design allows it to fit in smaller spaces, making it an excellent choice for urban gardens or areas with limited storage.

Overall, the Makita BCM3310 is an exceptional cordless lawn mower that combines power, efficiency, and user-friendly features. Ideal for the modern homeowner, it stands as a testament to Makita’s commitment to quality and innovation in gardening tools.