Ryobi Maintenance Instructions for CS26 and SS26: Spark Plug Replacement and More
Page 15

MAINTENANCE

INSTALLING LINE IN DUAL SPOOL™ FIXED LINE STRING HEAD INSERT

See Figure 21.

Use monofilament line between .095 in. and .105 in. diameter.

Stop the engine and disconnect the spark plug wire.

Gather two of the pre-cut lengths of trimmer line provided or cut two pieces of trimmer line in 11 in. lengths.

Insert the lines into the eyelets located on the sides of the string head. Line should be pushed in until approximately 1 in. protrudes from the holes on the top of the string head.

Remove old line by pulling it from the holes located on the top of the string head.

CLEANING THE EXHAUST PORT AND MUFFLER

NOTE: Depending on the type of fuel used, the type and amount of lubricant used, and/or your operating conditions, the exhaust port, muffler, and/or spark arrestor screen may be- come blocked with carbon deposits. If you notice a power loss with your gas powered tool, you may need to remove these deposits to restore performance. We highly recommend that only qualified service technicians perform this service.

SPARK ARRESTOR

The spark arrestor must be cleaned or replaced every 50 hours or yearly to ensure proper performance of your prod- uct. Spark arrestors may be in different locations depending on the model purchased. Please contact your nearest service dealer for the location of the spark arrestor for your model.

IDLE SPEED ADJUSTMENT

See Figure 22.

If the cutting attachment turns at idle, the idle speed screw needs adjusting on the engine. Turn the idle speed screw counterclockwise to reduce the idle RPM and stop the cut- ting attachment movement. If the cutting attachment still moves at idle speed, contact a service dealer for adjustment and discontinue use until the repair is made.

WARNING:

The cutting attachment should never turn at idle. Turn the idle speed screw counterclockwise to reduce the idle RPM and stop the cutting attachment, or contact a service dealer for adjustment and discontinue use until the repair is made. Serious personal injury may result from the cutting attachment turning at idle.

CLEANING AIR FILTER SCREEN

See Figures 23 - 24.

For proper performance and long life, keep air filter screen clean.

Remove the air filter cover by pushing down on the latch with your thumb while gently pulling on the cover.

Brush the air filter screen lightly to clean.

Replace the air filter cover by inserting the tabs on the bottom of the cover into the slots on the air filter base; push the cover up until it latches securely in place.

FUEL CAP

WARNING:

Check for fuel leaks. A leaking fuel cap is a fire hazard and must be replaced immediately. If you find any leaks, correct the problem before using the product. Failure to do so could result in a fire that could cause serious personal injury.

The fuel cap contains a non-serviceable filter and a check valve. A clogged fuel filter will cause poor engine perfor- mance. If performance improves when the fuel cap is loos- ened, check valve may be faulty or filter clogged. Replace fuel cap if required.

SPARK PLUG REPLACEMENT

This engine uses a Champion RCJ-6Y, NGK BPMR7A, or Ryobi AC00160 spark plug with .025 in. electrode gap. Use an exact replacement and replace annually.

STORING THE PRODUCT

Clean all foreign material from the product. Store idle unit indoors in a dry, well-ventilated area that is inaccessible to children. Keep away from corrosive agents such as garden chemicals and de-icing salts.

Abide by all ISO and local regulations for the safe storage and handling of gasoline.

When storing 1 month or longer:

Drain all fuel from tank into a container approved for gasoline. Run engine until it stops.

11 — English

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Toutes LES Versions Todas LAS Versiones Save this Manual for Future ReferenceCS26 Iii DE LA Herramienta Latch loquet, pestillo Introduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules for Trimmer USE Specific Safety RulesSymbols Symbol Signal MeaningSymbol Name Explanation Assembly FeaturesAttaching the Front Handle Installing the Power Head to the AttachmentRemoving the Attachment from the Power Head Attaching the Storage HangerOxygenated Fuels OperationTo Attach the Straight Shaft Grass Deflector SS26 Fueling and Refueling the TrimmerAdvancing the String Manually Advancing String Using the REEL-EASYTAP Advance SystemOperating the Trimmer Cutting TipsLine Replacement MaintenanceGeneral Maintenance Spool Replacement REEL-EASYTAP ­ADVANCE SystemCleaning AIR Filter Screen Installing Line in Dual Spool Fixed Line String Head InsertCleaning the Exhaust Port and Muffler Spark Arrestor Idle Speed AdjustmentTroubleshooting Gap. Refer to Spark Plug Replacement earlierSpeed. See Figure This Product WAS Manufactured with a Catalyst Muffler WarrantyLimited Warranty Statement MANUFACTURER’S Warranty Coverage Page Page Règles DE Sécurité Générales AvertissementLire Toutes LES Instructions Règles DE Sécurité Particulières Symbole NOM Explication SymbolesAssemblage CaractéristiquesInstallation DU Déflecteur D’HERBE Avertissement Installation DU BLOC-MOTEUR SUR L’ACCESSOIRERetrait DE L’ACCESSOIRE DU Bloc Moteur Installation DE LA Poignée AvantCarburants Oxygénés Installation DU Déflecteur D’HERBE D’ARBRE Droit SS26Utilisation Approvisionnement EN CarburantPour toute assistance, appeler le  Utilisation DU TAILLE-BORDURESConseils DE Coupe Avance Manuelle DE LA Ligne DE CoupeEntretien Général Remplacement DE LigneInstallation DE LA Bobine À FIL Fixe Dual Spool EntretienBouchon DU Réservoir Avertissement Remplacement DE LA BougieRéglage DU Ralenti Nettoyage DU Filtre À AIR ÉcranDépannage Garantie ’AIDEFonctionnement Chaque année Énoncé DE LA Garantie Limitée Responsabilités DU Propriétaire Dans LE Cadre DE LA Garantie Reglas DE Seguridad Generales AdvertenciaLEA Todas LAS Instrucciones Reglas DE Seguridad Específicas Precaución Symbolo Nombre ExplicatiónSímbolos PeligroArmado CaracterísticasMontaje DEL Mango Delantero Instalación DEL Cabezal Motor EN EL AditamentoDesmontaje DEL Aditamento DEL Cabezal Motor Montaje DE LA ASA DE ALMACENAMIENTOArranque Y Apagado FuncionamientoPara Montar EL Deflector DE Pasto Para EJE Recto SS26 Combustibles OxigenadosCuchilla DE Corte DEL Hilo EN EL Deflector DE Hierba Manejo DE LA RecortadoraSugerencias Para Cortar Avance Manualmente EL HiloMantenimiento Mantenimiento GeneralReabastecimiento DEL Hilo Limpieza DEL Filtro DE Aire Pantalla Limpieza DEL Orificio DE Escape Y DEL SilenciadorParachispas Ajuste DE LA Marcha LentaEl motor no arranca No hay chispa Solución DE ProblemasGarantía Conjunto DE Silenciador Catalítico4050 Declaración DE LA Garantía Limitada Cobertura DE LA Garantía DEL Fabricante California Propuesta DE LEY NÚM Manuel D’UTILISATION / Manual DEL OperadorCalifornia Proposition Proposition 65 DE L’ÉTAT DE Californie

SS26 RY28040, CS26 RY28020 specifications

The Ryobi CS26 RY28020 and SS26 RY28040 are two powerful and efficient gas-powered string trimmers, tailored for both residential and professional landscaping tasks. These models are synonymous with durability, performance, and ease of use, making them staple tools for homeowners and landscape professionals alike.

One of the standout features of the CS26 is its 26cc two-cycle engine, which delivers impressive power while maintaining a lightweight design. This engine provides ample torque, making it effective for tackling thick grass and weeds. The SS26 offers a similar robust performance with its 26cc engine, designed to handle tough outdoor conditions, ensuring precision in trimming and maintenance tasks.

Both models come equipped with Ryobi's innovative Easy Start System. This technology simplifies the starting process, requiring less effort and providing a quick and reliable start every time. This feature is particularly beneficial for users who value convenience and efficiency in their gardening routines.

Ergonomics also play a crucial role in the design of these trimmers. With an adjustable handlebar and a lightweight build, users can easily maneuver the trimmers, reducing fatigue during extended use. The curved shaft design of the CS26 allows for easier access to hard-to-reach areas, while the straight shaft of the SS26 offers greater reach and increased cutting convenience.

Another notable characteristic is the automatic feed spool, which allows the trimmer line to extend automatically as needed. This saves time and effort, eliminating the hassle of manual line adjustments and keeping you focused on your task. The robust cutting width of both trimmers ensures efficient coverage, allowing you to complete your yard work swiftly.

Durability is also a key factor; both models are engineered with high-quality materials that withstand the rigors of outdoor use. The reliable construction paired with easy maintenance features not only enhances longevity but also ensures that both the CS26 and SS26 can handle various landscaping challenges over the years.

In summary, the Ryobi CS26 RY28020 and SS26 RY28040 are excellent choices for anyone looking to invest in a gas-powered string trimmer that balances power, convenience, and durability. With their advanced technologies, ergonomic designs, and user-friendly features, these trimmers are designed to meet diverse trimming needs while ensuring a comfortable user experience. Whether for a small garden or a larger landscaping project, these models provide the tools necessary to achieve a professionally manicured look.
Top Page Image Contents