Black & Decker NHT518 instruction manual Before USE, Place the battery pack into the tool until it

Page 7

been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to service center for recycling.

CAUTION: When not in use, place tool on its side on a stableSome toolssurfacewithwherlargebatteryit will notpackscausewill astandtrippinguprightor fallingbut mayhazardbe easily. knocked over.

ABattbatteryystorageCap Informationand carrying cap is provided for use whenever the battery is out of the tool or charger. Remove cap before placing battery in charger or tool.Battery Cap

WARNING: Fire hazard. Do not store or carry battery so Forthatexample,metal objectsdo notcanplacecontactbatteryexposedin aprons,batterypockets, tool boxes,terminalsproduct. kit boxes, drawers, etc., with loose nails, screws, keys, etc. Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductiveThe US

Departmentmate ials suchof Transportationas keys, c ins,Hazardoush nd toolsMaterialand thRegulationslike. (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.

IMPORTANTCHARGINGSAFETY

INSTRUCTIONS

CHARGING PROCEDURE

THE BATTERY PACK IS NOT FULLY CHARGED AT THE

FACTORY. CHARGE BATTERY PACK FOR AT LEAST 9 HOURS

The charger is designed to use standard household 120 volt 60 Hz

BEFORE USE.

 

power.

 

1. Plug the charger into any standard 120 Volt

 

60 Hz electrical outlet (figure 1).

 

2. Slide the charger onto the battery pack as

1

shown in f gure 2 and let the battery pack

 

charge initially for 9 hours. After the initial

 

charge, under normal usage, your battery

 

pack should be fully charged in 6 to 9 hours.

 

2a) During charging the green LED will appear.

 

2b) When charging is complete the green LED

2

will go off.

 

3. Unplug charger, and remove the battery pack.

3

Place the battery pack into the tool until it

NOTE: To remove the battery pack, press

 

“clicks” into place.

 

down on the release button on the back of the

 

battery pack and slide out (figure 3).

 

IMPORTANT CHARGING NOTES

 

1. After normal usage, your battery pack should be fully charged in

6 to 9 hours. If the battery pack is run-down completely, it may

take up to 9 hours to become fully charged. Your battery pack

was sent from the factory in an uncharged condition. Before

attempting to use it, it must be charged for at least 9 hours.

2. DO NOT charge the battery pack in an air temperature below

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Hedge Trimmer CHARGE.charge batteryAvoid Dangerous Environment Do not use or charge USE Battery Operated Unit only with specificallyAvoid Unintentionalstarting Donʼt carry hedge trimmer Always Wear EYE Protection Wear safety glasses orStore Idle Hedge Trimmer Indoors When not in use Ground Fault Circuit Interrupter Gfci protectionSmaller the gauge number, the heavier the cord Microscopic particlesNever Charging Chart for Minimum Wire Size AWG of Extension CordsNameplate Rating Amps 0 Important Charging Notes Place the battery pack into the tool until itBefore USE Clicks into placeStorage Recommendation Leaving the Batterypack in the ChargerNever hold the unit by the bladefigureguard5 Side Trimming Hedges MaintenanceTrimming NEW Growth Level Hedges FigurHas established programs in the United States and Canada to Conscious alternativeProblem Possible Cause Possible Solution TroubleshootingMode DʼEMPLOI Porter DES Vêtements Appropriés Sécurité Générales Pour Tous LES OutilsReduction DES Risques ET DES Blessures Tenir Compte DU Milieu DE TRAVAIL. Ne pas se servir niVérifier LES Pièces ENDOMMAGÉES. Lorsque loutil est Porter DES Lunettes DE SÉCURITÉ. Porter également unÉviter LES Démarrages ACCIDENTELS. Ne pas laisser le Ranger LE TAILLE-HAIE À L’INTÉRIEUR. Il faut ranger leNE PAS Ouvrir NI Mutiler le bloc-pile. Lélectrolyte qui sen Manipuler LES BLOCS-PILESavec soin afin de ne pas lesCourt-circuiter avec des matériaux conducteurs comme des Pourrait alors surchauffer et causer des brûlures’autres fins que cell s de charger les piles r chargeables Que ceux qui sont mentionnés dans le présent mode d’emploiAdéquat AWG, American Wire Gauge calibrage américain Ces chargeurs n’ont pas été conçus pour être utilisés àNe pas démonter le chargeur l’apporter à un centre de Rmanente sur une surface quelconque. Le chargeur estNe pas monter le chargeur sur un mur ni le fixer de manière Ne jamais se servir d’un chargeur qui a sub un choc violentDans le chargeur ou lʼoutil Signaletique a 0 10,0Tableau DES Calibres DE Fils Minimums AWG Pour LES Rallonges Valeur Nominale DE LA PlaqueUSINE. Charge BLOC-PILE Pendant AU Moins 9 Heures LE BLOC-PILE N’EST PAS Complètement Chargé ENAvant Utilisation Ensemble DE Piles Dans LE Chargeur Fonctionnement InterrupteurInstructions Relatives a LA CoupeHaies Saisir lʼoutil EntretienNivelage DES Haies Coupe Latérale DESLe recyclage des piles rechargeables et Obtenir le remplacement gratuitCoupe le courant au moment dʼéteindre Déplacer la gâchette principaleManual DE Instrucciones Evite Ambientes Peligrosos No utilice podadoras de UNA Unidad Accionada a Bateria con baterías integrales oLEA y comprenda todas las instrucciones Utilice LA Unidad Accionada a Bateriasolo con elGuarde LA Podadora Bajo Techo Cuando no LA USE Cable Prolongador Que cada prolongacióntenga la medida mínima del conductor Funcionar en conjuntoNo exponga el cargador a la lluvia ni a la nieve De alguna otra formaTablade Medidasminimas Deconductor Awgpara Carga DE LA BateríaAmperios Segun Placa 0 a De costado en una superficieestable en la que no provocará Advertencia Riesgo de incendioNoguarde o transporte la batería de ninguna manera que Precaución Cuando no se utilice, coloque la herramientaQuede firme n su lug r Paquetede Bateríasno Vienen CompletamenteCargadas DE FÁBRICA. Paquete DE Baterías DE Carga DE AL Menos 9 Horas Antes DE SU USODejando LA Batería EN EL Cargador Instrucciones DE OperacionCorte Lateral DE Setos MantenimientoInformacion DE Mantenimiento Garantia Completa DE DOS Anos Para USO EN EL Hogar Deteccion DE Problemas Page Product Infomation · Identificacion DEL Producto Solamente Para Propositos DE Mexico
Related manuals
Manual 2 pages 30.01 Kb

NHT518 specifications

Black & Decker is synonymous with quality and innovation in the realm of power tools and outdoor equipment. Among its extensive lineup, the NHT518, NHT518G, and NHT518L hedge trimmers stand out for their performance and user-friendly features, making them ideal choices for both homeowners and professionals.

The NHT518 series is designed for efficient hedge maintenance, featuring a robust, lightweight design that allows users to maneuver easily through their gardening tasks. One of the main highlights of this trimmer is its 20-inch dual-action blade, which significantly reduces vibration while trimming. This feature not only enhances user comfort but also ensures clean, precise cuts, contributing to healthier plants and an aesthetically pleasing landscape.

Equipped with a powerful and efficient motor, the NHT518 series can tackle even the toughest hedges with ease. The models feature a 40V lithium-ion battery in the NHT518 and NHT518L, providing ample runtime for large projects without the hassle of cords. The NHT518G, which includes a geared design, offers variable speed control, allowing the user to adjust the blade speed according to the thickness of the branches being trimmed.

Safety is also a priority for Black & Decker. These models come with a lock-off switch that prevents accidental starts, adding an extra layer of protection during operation. The grips are ergonomically designed to enhance comfort, reducing fatigue during prolonged use. Additionally, the transparent blade guard is designed to offer visibility while protecting both the user and the blades from debris.

Another characteristic that sets the NHT518 series apart is its easy maintenance. The tool-free blade change feature allows users to replace blades quickly and efficiently, ensuring that tools remain in optimal condition. The durability of the blades is also noteworthy, as they are built to withstand wear and tear, thereby extending the life of the trimmer.

Users will appreciate the portability and convenience offered by these models. With their cordless design, operators can move freely without being hindered by power outlets or extension cords, making them ideal for tackling hedges in various locations around the yard.

In conclusion, the Black & Decker NHT518, NHT518G, and NHT518L hedge trimmers combine powerful technology with user-friendly features, ensuring that garden maintenance is both efficient and enjoyable. With their performance, convenience, and safety features, these trimmers are valuable tools for anyone looking to achieve beautiful hedges and landscapes.
Top Page Image Contents