Snapper WLT200H481BV2, LT180H421BV2 Annually END of Each Season, 2, Fuel Filter, Spark Plug

Page 15

Section 3 - MAINTENANCE

3.3.4.TRACTOR LUBRICATION

6.Steering Drag Link

Lubricate both ends of steering drag link with a small amount of 30 wt. motor oil from an oil can. See

Figure 3.8.

DRAG LINK

LUBRICATION

OINT

FIGURE 3.8

7.Steering Tie Rod

Lubricate both ends of steering tie rod with a small amount of 30 wt. motor oil from an oil can. See

Figure 3.9.

LUBRICATE

BOTH ENDS

OF TIE ROD

FIGURE 3.9

8.Park Brake Lever

Using 30 wt. motor oil, lubricate the park brake lever mechanism pivot points, which are located on the left hand underside of tractor. See Figure 3.10. Lubricate mechanism with a thin coat of 30 wt. motor oil.

PARK BRAKE

LEVER

LUBRICATE

COMPONENTS ON

UNDERSIDE OF

TRACTOR

FIGURE 3.10

9.Deck Lift Mechanism

Lubricate all wear and pivot points of the deck lift.

3.4ANNUALLY (END OF EACH SEASON)

Perform all maintenance as described in Section "SERVICE - EVERY 25 OPERATING HOURS". Also see Service Schedule.

3.4.1. ENGINE

1.Service engine according to engine owner's manual.

3.4.2, FUEL FILTER

1.Service fuel filter as instructed below, on COLD ENGINE ONLY!

NOTE: It may be necessary to drain the fuel tank before removing fuel filter to prevent spillage of gasoline.

2.Locate fuel filter. Remove hose clamps and fuel hoses from both sides of fuel filter.

3.Install new fuel filter part number 1-4359. See Figure 3.11.

NEW FUEL FILTER

PART NUMBER 1-4359'

FIGURE 3.11

4.Fill fuel tank with fresh gasoline. Refer to engine owner's manual for fuel specifications.

3.4,3. SPARK PLUG

Remove and replace engine spark plug. Refer to engine owner's manual for correct replacement plug and gap specifications.

3.4.4, HYDROSTATIC TRANSMISSION OIL

The hydrostatic transmission does not require

maintenance. If any problems arise return immediately to a Snapper dealer.

15

Image 15
Contents Model Number Explanation Oolo IProtection Against Tipovers Protection for ChildrenOperation MaintenanceTable of Contents Components Controls FamiliarizationOperators Seat Adjustment 1. Front to Rear Adjustment PRE-START ChecklistStarting & Operation 2,3.1. Starting Engine WaydowntostartStopping Wheel Drive Starting & Operation 2,3.2, Starting Wheel Drive3, Stopping Mower Blades Setting Park BrakeCutting Height Adjustment StoppingRolling Hydro Models Rolling Tractor with Engine OFFReverse Lockout Mechanism Override Reverse Lockout Mechanism2, Check Blade Brake Service After First 5 HoursIntroduction Change Engine OILAir Filter Service Every 25 Operating Hours 3.3.1. Check EngineCheck Deck Drive Belt Engine Cooling SystemClutch/Brake Pivot Check Blade BrakeTractor Lubrication Front Wheel BearingsAnnually END of Each Season 2, Fuel Filter3. Spark Plug 2, Blade Belt Adjustment Engine Adjustments & RepairMower Deck & Component Adjustments 1, Blade Brake AdjustmentFRONT-To-REAR 42 Decks Mower Deck Adjustment LevelnessMower Deck Adjustment Levelness SIDE-To-SIDE 48 Decks TOP View of DeckOn Next Front To Rear Tractor Drive Components 1. Brake Adjustment Steering Adjustment3, Shifter Adjustment Check for creep in neutral. Start engine. Move Shifter Adjustment4, Traction Drive Belt Adjustment Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Ninja Blade Sharpening3, Standard Blade Sharpening 5 & 48 Mower Blade Replacement Traction Drive Belt Replacement 42 Mower Deck RemovalDeck Shown View from Underneath Tractor D4SWIVELiiiiiill Sectorplates Spindle Pulleys TOP View Mower Deck 4. Battery Storage Battery Battery RemovalBattery Installation 3. Battery ServiceFive Ball Hydrometer Battery TestingNEW Battery Preparation Chart State of ChargeAvailable Accessories Electrical System Probable Cause Corrective Action Engine Stalls AfterRunning Snapper Troubleshooting GuideMower Blades Drive BeltsDisclaimer of Warranty 3YEARLIMITEDWARRANTYIllustration of how dirt can How Maintenance can protect it Cost YOU Moneyi That dirt willCheck OIL Level Before Each START-UP Scuffed wallsCatlor, poor air cleaner service or overheating AIr CIseasr FuelTank ChokeSpark plug Throttle control Blade Snapper Product Registration Form SNAPPERMcDonough,GA,, 30253 U.S.A

LT200H481BV2, WLT180H421BV2, WLT200H481BV2, LT180H421BV2 specifications

The Snapper LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are versatile riding lawn mowers that cater to homeowners seeking efficient lawn care solutions. Each model is engineered with a combination of power, durability, and advanced features, making them suitable for a variety of yard sizes and terrains.

The Snapper LT180H421BV2 is powered by a robust 18 HP Briggs & Stratton engine, providing reliable performance and ease of use. With a 42-inch cutting deck, this model offers a balance between maneuverability and cutting efficiency. The LT180H421BV2 features a comfortable high-back seat, allowing users to enjoy extended mowing sessions without discomfort. Its steering system is designed for effortless control, making it ideal for navigating around trees and flower beds.

On the other hand, the WLT200H481BV2 boasts a more powerful 20 HP engine, paired with a wide 48-inch cutting deck. This model is equipped with a hydrostatic transmission for smooth acceleration and deceleration, allowing for a responsive and enjoyable mowing experience. The WLT200H481BV2 also includes a dual-blade system, enhancing cutting performance and delivering a clean, manicured finish.

The WLT180H421BV2 combines the advantages of its counterparts with an 18 HP engine and a 42-inch cutting deck. This model is designed for both efficiency and power, making it suitable for homeowners with medium to large lawns. Its compact design enables easy storage and maneuverability in tight spaces, while still offering a comfortable operator experience.

Lastly, the LT200H481BV2 features a powerful 20 HP engine alongside a 48-inch cutting deck, representing the pinnacle of Snapper's residential riding mower technology. It incorporates a premium cut quality with its innovative three-blade system. The hydrostatic transmission ensures smooth operation, allowing users to tackle any lawn challenge effectively.

All these models showcase Snapper’s unwavering commitment to quality and innovation, making lawn maintenance a more efficient and enjoyable task. With comfortable seating, ergonomic controls, and durable construction, the LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are designed for performance and convenience. These mowers truly exemplify the perfect blend of technology and functionality for today's homeowners.