Snapper LT180H421BV2, LT200H481BV2 Battery Battery Removal, Battery Installation, Battery Service

Page 29

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.5BATTERY

4.5.1. BATTERY REMOVAL

1.Raise operator's seat.

2.Remove the two adjusting knobs.

3.Remove seat assembly and move forward. Use care not to disconnect wires from seat switch. See

Figure 4.36.

REMOVE ADJUSTING -

KNOBS AND MOVE

(+) CABLE LAST

REMOVE NEGATIVE (-)

CABLE FIRST

FIGURE 4.37

WARNING

FIGURE 4.36

4.Remove negative ( - ) cable first.

5.Remove positive ( + ) cable last.

6.Remove battery. See Figure 4.37.

WARNING

Cables must be connected to battery terminals in the proper position as shown. DO NOT attempt to charge battery while installed on tractor. DO NOT use "BOOST" chargers on the battery. If battery is removed, DO NOT operate engine without insulating Positive + battery cable terminal with electrical tape, or sparking from battery cables can result.

4.5.2.BATTERY INSTALLATION

1.Slide battery into battery housing.

2.Connect positive (+) cable first.

3.Connect negative (-) cable last.

4.Reinstall seat assembly. Use care not to disconnect wires from seat switch.

5.Reinstall the two adjusting knobs.

6.Lower operator's seat.

The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid. Wear eye protection. Wash affected areas immediately after having eye or skin contact with electrolyte (acid). Battery acid is corrosive. Rinse empty acid containers with water and mutilate before discarding. If acid is spilled on battery, bench, or clothing, etc., Flush with clear water and neutralize with baking soda.

4.5,3. BATTERY SERVICE

1.Remove battery. Refer to Section "BATTERY REMOVAL".

2.Place battery in a well ventilated area on a level surface.

3.Using distilled water, refill ceils as required to cover cell plates of which can also be visualized through the

plastic battery case.

4.With celt caps removed, connect battery charger to battery terminals. Red to positive (+) terminal and black

to negative (-) terminal.

5.Slow charge battery at 1 amp for 10 hours.

6.If battery will not accept charge or is partially charged after 10 hours of charging at 1 amp, replace with new battery.

4.5,4. BATTERY STORAGE

When out of season, it is recommended the battery be removed, charged and stored.

1.Remove battery. Refer to Section "BATTERY REMOVAL".

2.Perform battery service.

3.Bring battery to full charge, if required.

4.Store battery in an area away from the RIDER on a wood surface. DO NOT STORE BATTERY ON A CONCRETE SURFACE.

29

Image 29
Contents Model Number Explanation Oolo IProtection Against Tipovers Protection for ChildrenOperation MaintenanceTable of Contents Components Controls FamiliarizationOperators Seat Adjustment 1. Front to Rear Adjustment PRE-START ChecklistStarting & Operation 2,3.1. Starting Engine WaydowntostartStopping Wheel Drive Starting & Operation 2,3.2, Starting Wheel DriveCutting Height Adjustment Setting Park BrakeStopping 3, Stopping Mower BladesRolling Hydro Models Rolling Tractor with Engine OFFReverse Lockout Mechanism Override Reverse Lockout MechanismIntroduction Service After First 5 HoursChange Engine OIL 2, Check Blade BrakeCheck Deck Drive Belt Service Every 25 Operating Hours 3.3.1. Check EngineEngine Cooling System Air FilterTractor Lubrication Check Blade BrakeFront Wheel Bearings Clutch/Brake Pivot3. Spark Plug Annually END of Each Season2, Fuel Filter Mower Deck & Component Adjustments Engine Adjustments & Repair1, Blade Brake Adjustment 2, Blade Belt AdjustmentFRONT-To-REAR 42 Decks Mower Deck Adjustment LevelnessOn Next Mower Deck Adjustment Levelness SIDE-To-SIDE 48 DecksTOP View of Deck Front To Rear 3, Shifter Adjustment Tractor Drive Components 1. Brake AdjustmentSteering Adjustment 4, Traction Drive Belt Adjustment Shifter AdjustmentMower Blade Service Standard Blade Wear Limits Check for creep in neutral. Start engine. Move3, Standard Blade Sharpening Ninja Blade Wear LimitsNinja Blade Sharpening Deck Shown 5 & 48 Mower Blade ReplacementTraction Drive Belt Replacement 42 Mower Deck Removal View from Underneath Tractor D4SWIVELiiiiiill Sectorplates Spindle Pulleys TOP View Mower Deck Battery Installation Battery Battery Removal3. Battery Service 4. Battery StorageNEW Battery Preparation Battery TestingChart State of Charge Five Ball HydrometerAvailable Accessories Electrical System Running Probable Cause Corrective ActionEngine Stalls After Snapper Troubleshooting GuideMower Blades Drive BeltsDisclaimer of Warranty 3YEARLIMITEDWARRANTYIllustration of how dirt can How Maintenance can protect it Cost YOU Moneyi That dirt willCheck OIL Level Before Each START-UP Scuffed wallsSpark plug Throttle control Blade Catlor, poor air cleaner service or overheatingAIr CIseasr FuelTank Choke Snapper Product Registration Form SNAPPERMcDonough,GA,, 30253 U.S.A

LT200H481BV2, WLT180H421BV2, WLT200H481BV2, LT180H421BV2 specifications

The Snapper LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are versatile riding lawn mowers that cater to homeowners seeking efficient lawn care solutions. Each model is engineered with a combination of power, durability, and advanced features, making them suitable for a variety of yard sizes and terrains.

The Snapper LT180H421BV2 is powered by a robust 18 HP Briggs & Stratton engine, providing reliable performance and ease of use. With a 42-inch cutting deck, this model offers a balance between maneuverability and cutting efficiency. The LT180H421BV2 features a comfortable high-back seat, allowing users to enjoy extended mowing sessions without discomfort. Its steering system is designed for effortless control, making it ideal for navigating around trees and flower beds.

On the other hand, the WLT200H481BV2 boasts a more powerful 20 HP engine, paired with a wide 48-inch cutting deck. This model is equipped with a hydrostatic transmission for smooth acceleration and deceleration, allowing for a responsive and enjoyable mowing experience. The WLT200H481BV2 also includes a dual-blade system, enhancing cutting performance and delivering a clean, manicured finish.

The WLT180H421BV2 combines the advantages of its counterparts with an 18 HP engine and a 42-inch cutting deck. This model is designed for both efficiency and power, making it suitable for homeowners with medium to large lawns. Its compact design enables easy storage and maneuverability in tight spaces, while still offering a comfortable operator experience.

Lastly, the LT200H481BV2 features a powerful 20 HP engine alongside a 48-inch cutting deck, representing the pinnacle of Snapper's residential riding mower technology. It incorporates a premium cut quality with its innovative three-blade system. The hydrostatic transmission ensures smooth operation, allowing users to tackle any lawn challenge effectively.

All these models showcase Snapper’s unwavering commitment to quality and innovation, making lawn maintenance a more efficient and enjoyable task. With comfortable seating, ergonomic controls, and durable construction, the LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are designed for performance and convenience. These mowers truly exemplify the perfect blend of technology and functionality for today's homeowners.