Snapper LT200H481BV2 Tractor Drive Components 1. Brake Adjustment, Steering Adjustment

Page 20

Section 4 - ADJUSTMENT & REPAIR

WARNING

e-_FUELTANK

DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4,3 TRACTOR DRIVE COMPONENTS

4,3,1. BRAKE ADJUSTMENT

When adjusted properly, the brake should stop the tractor in approximately 6 feet or less from top speed. Drive the machine at maximum forward speed and apply the brake. If stopping distance is greater than 6 feet, brake adjustment is required.

1.Turn engine "OFF". Remove key.

2.Locate brake adjustment nut underneath the left side at the rear of tractor. See Figure 4.9.

3.Turn nut 1 turn clockwise to increase braking action. DO NOT over tighten brake adjustment.

4.Start engine and test brake.

5.Continue adjustment as described above until proper brake function is achieved.

ROTATE ADJUSTING NUT

CLOCKWISETOINCREASE/"

BRAKING OR COUNTER

CLOCKWISE TO DECREASE

BRAKING

FIGURE 4.9

4.3.2.STEERING ADJUSTMENT

Should excessive "Play" be noted in the steering, adjust as follows:

1.Turn engine "OFF". Remove key.

2.From left side of tractor, locate the steering sector below fuel tank. See Figure 4.10.

ROTATE TO

REDUCE"PLAY"

MOUNTING NUT

FIGURE 4.10

3.Loosen the eccentric mounting nut and rotate the eccentric clockwise until steering "Play" is reduced. See Figure 4.10.

4.Tighten eccentric mounting nut.

4,3,3, SHIFTER ADJUSTMENT

The shift linkage is set at the factory and should not require further adjustment. The shifter is adjusted properly when the speed control lever can be placed at rear edge of the neutral detent and the tractor remains absolutely stationary. If motion is detected, neutral adjustment will be required. DO NOT operate a machine that creeps when shifted to neutral.

1.Stop engine. Remove key.

2.Move speed control lever to rear edge of neutral detent and hold firmly.

3.Locate neutral adjustment nut underneath the right rear of the tractor. See Figure 4.11.

NEUTRAL

ADJUSTMENT

NUT

FIGURE 4.11

20

Image 20
Contents Oolo I Model Number ExplanationProtection for Children Protection Against TipoversMaintenance OperationTable of Contents Familiarization Components ControlsPRE-START Checklist Operators Seat Adjustment 1. Front to Rear AdjustmentWaydowntostart Starting & Operation 2,3.1. Starting EngineStarting & Operation 2,3.2, Starting Wheel Drive Stopping Wheel DriveSetting Park Brake Cutting Height AdjustmentStopping 3, Stopping Mower BladesRolling Tractor with Engine OFF Rolling Hydro ModelsReverse Lockout Mechanism Reverse Lockout Mechanism OverrideService After First 5 Hours IntroductionChange Engine OIL 2, Check Blade BrakeService Every 25 Operating Hours 3.3.1. Check Engine Check Deck Drive BeltEngine Cooling System Air FilterCheck Blade Brake Tractor LubricationFront Wheel Bearings Clutch/Brake Pivot3. Spark Plug Annually END of Each Season2, Fuel Filter Engine Adjustments & Repair Mower Deck & Component Adjustments1, Blade Brake Adjustment 2, Blade Belt AdjustmentMower Deck Adjustment Levelness FRONT-To-REAR 42 DecksOn Next Mower Deck Adjustment Levelness SIDE-To-SIDE 48 DecksTOP View of Deck Front To Rear 3, Shifter Adjustment Tractor Drive Components 1. Brake AdjustmentSteering Adjustment Shifter Adjustment 4, Traction Drive Belt AdjustmentMower Blade Service Standard Blade Wear Limits Check for creep in neutral. Start engine. Move3, Standard Blade Sharpening Ninja Blade Wear LimitsNinja Blade Sharpening Deck Shown 5 & 48 Mower Blade ReplacementTraction Drive Belt Replacement 42 Mower Deck Removal View from Underneath Tractor D4SWIVELiiiiiill Sectorplates Spindle Pulleys TOP View Mower Deck Battery Battery Removal Battery Installation3. Battery Service 4. Battery StorageBattery Testing NEW Battery PreparationChart State of Charge Five Ball HydrometerAvailable Accessories Electrical System Running Probable Cause Corrective ActionEngine Stalls After Troubleshooting Guide SnapperDrive Belts Mower Blades3YEARLIMITEDWARRANTY Disclaimer of WarrantyIllustration of how dirt can How Maintenance can protect it That dirt will Cost YOU MoneyiScuffed walls Check OIL Level Before Each START-UPSpark plug Throttle control Blade Catlor, poor air cleaner service or overheatingAIr CIseasr FuelTank Choke Snapper Product Registration Form SNAPPERMcDonough,GA,, 30253 U.S.A

LT200H481BV2, WLT180H421BV2, WLT200H481BV2, LT180H421BV2 specifications

The Snapper LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are versatile riding lawn mowers that cater to homeowners seeking efficient lawn care solutions. Each model is engineered with a combination of power, durability, and advanced features, making them suitable for a variety of yard sizes and terrains.

The Snapper LT180H421BV2 is powered by a robust 18 HP Briggs & Stratton engine, providing reliable performance and ease of use. With a 42-inch cutting deck, this model offers a balance between maneuverability and cutting efficiency. The LT180H421BV2 features a comfortable high-back seat, allowing users to enjoy extended mowing sessions without discomfort. Its steering system is designed for effortless control, making it ideal for navigating around trees and flower beds.

On the other hand, the WLT200H481BV2 boasts a more powerful 20 HP engine, paired with a wide 48-inch cutting deck. This model is equipped with a hydrostatic transmission for smooth acceleration and deceleration, allowing for a responsive and enjoyable mowing experience. The WLT200H481BV2 also includes a dual-blade system, enhancing cutting performance and delivering a clean, manicured finish.

The WLT180H421BV2 combines the advantages of its counterparts with an 18 HP engine and a 42-inch cutting deck. This model is designed for both efficiency and power, making it suitable for homeowners with medium to large lawns. Its compact design enables easy storage and maneuverability in tight spaces, while still offering a comfortable operator experience.

Lastly, the LT200H481BV2 features a powerful 20 HP engine alongside a 48-inch cutting deck, representing the pinnacle of Snapper's residential riding mower technology. It incorporates a premium cut quality with its innovative three-blade system. The hydrostatic transmission ensures smooth operation, allowing users to tackle any lawn challenge effectively.

All these models showcase Snapper’s unwavering commitment to quality and innovation, making lawn maintenance a more efficient and enjoyable task. With comfortable seating, ergonomic controls, and durable construction, the LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are designed for performance and convenience. These mowers truly exemplify the perfect blend of technology and functionality for today's homeowners.