Snapper WLT180H421BV2 Battery Testing, NEW Battery Preparation, Chart State of Charge

Page 30

Section 4 - ADJUSTMENT & REPAIR

IL WARNING 41

DO NOT OVERFILL! Never attempt to service or I charge the battery while it is installed on the machine. DO NOT use "BOOST" chargers on the battery.

4.5.5.BATTERY TESTING

There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that wilI be discussed. It'sthe simplest and most commonly used. An unloaded test is made on a battery without discharging current. To perform unloaded testing, check charge condition using either a hydrometer or voltmeter.

1.Using a voltmeter, voltage readings appear instantly to show the state of charge. Remember to hook the positive lead to the battery's positive terminal, and the negative Iead to the negative terminal.

2, A hydrometer measures the specific gravity of each ceil. The specific gravity tells the degree of charge; generally, a specific gravity of about 1.265 to 1.280 indicates fulI charge. A reading of 1.230 to 1.260 indicates the battery should be charged. The Battery Condition chart below shows the charge level as measured by syringe float hydrometer, digital voltmeter and five ball hydrometer.

4,5.6. NEW BATTERY PREPARATION

1.Remove battery from carton.

2.Place battery in a well ventilated area on a level non- concrete surface.

3.Remove battery cell caps. FilI cells as required with electrolyte (purchased separately) to proper level. Fill to 3/16" above cell plates. Filling battery with electrolyte wilI bring the battery to 80% charged state.

4.With cell caps removed, connect battery charger to battery terminals; RED to positive (+) and BLACK to negative (-) terminal.

IMPORTANT: 3/16" above cell plates is the recommended level. DO NOT place anything in battery other than specified electrolyte.

5.Slow charge the battery at 1 amp for 2 hours to bring the battery to full charge.

6.After charging, check level of electrolyte and add as needed to bring level to 3/16" above ceil plates.

7.Reinstall cell caps.

8.Slide battery partially into battery housing.

9.Connect positive (+) cable (red) first, from wiring harness to the positive terminal (+) on battery using bolt and nut provided in hardware bag. Connect negative (-) cable (black) last, to negative terminal (-) on battery using bolt and nut. Apply a small amount of grease over

terminals to prevent corrosion.

10.Insert battery completely into battery housing.

11.Reinstall seat assembly.

WARNING

Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal, which could cause sparks. Cables must be connected to battery terminals in the proper position. RED (Positive) cable must go to the ( + ) terminal, BLACK (Negative) cable must go to the ( - ) terminal.

 

 

 

Battery Condition

Chart

 

 

State of Charge

 

Syringe Hydrometer

Digital Voltmeter

Five Ball Hydrometer

100% Charged w/Sulfate

Stop

1.280

12.80v

Five Balls Floating

1.265

12.60v

100% Charged

 

Four Balls Floating

75%

Charged

 

1.210

12.40v

Three Balls Floating

50%

Charged

 

1.160

12.10v

Two Balls Floating

25%

Charged

 

1.120

11.90v

One Ball Floating

0% Charged

 

Less than 1.100

Less than 11.80v

Zero Balls Floating

 

 

 

30

Image 30
Contents Oolo I Model Number ExplanationProtection for Children Protection Against TipoversMaintenance OperationTable of Contents Familiarization Components ControlsPRE-START Checklist Operators Seat Adjustment 1. Front to Rear AdjustmentWaydowntostart Starting & Operation 2,3.1. Starting EngineStarting & Operation 2,3.2, Starting Wheel Drive Stopping Wheel DriveStopping Setting Park BrakeCutting Height Adjustment 3, Stopping Mower BladesRolling Tractor with Engine OFF Rolling Hydro ModelsReverse Lockout Mechanism Reverse Lockout Mechanism OverrideChange Engine OIL Service After First 5 HoursIntroduction 2, Check Blade BrakeEngine Cooling System Service Every 25 Operating Hours 3.3.1. Check EngineCheck Deck Drive Belt Air FilterFront Wheel Bearings Check Blade BrakeTractor Lubrication Clutch/Brake PivotAnnually END of Each Season 2, Fuel Filter3. Spark Plug 1, Blade Brake Adjustment Engine Adjustments & RepairMower Deck & Component Adjustments 2, Blade Belt AdjustmentMower Deck Adjustment Levelness FRONT-To-REAR 42 DecksMower Deck Adjustment Levelness SIDE-To-SIDE 48 Decks TOP View of DeckOn Next Front To Rear Tractor Drive Components 1. Brake Adjustment Steering Adjustment3, Shifter Adjustment Mower Blade Service Standard Blade Wear Limits Shifter Adjustment4, Traction Drive Belt Adjustment Check for creep in neutral. Start engine. MoveNinja Blade Wear Limits Ninja Blade Sharpening3, Standard Blade Sharpening 5 & 48 Mower Blade Replacement Traction Drive Belt Replacement 42 Mower Deck RemovalDeck Shown View from Underneath Tractor D4SWIVELiiiiiill Sectorplates Spindle Pulleys TOP View Mower Deck 3. Battery Service Battery Battery RemovalBattery Installation 4. Battery StorageChart State of Charge Battery TestingNEW Battery Preparation Five Ball HydrometerAvailable Accessories Electrical System Probable Cause Corrective Action Engine Stalls AfterRunning Troubleshooting Guide SnapperDrive Belts Mower Blades3YEARLIMITEDWARRANTY Disclaimer of WarrantyIllustration of how dirt can How Maintenance can protect it That dirt will Cost YOU MoneyiScuffed walls Check OIL Level Before Each START-UPCatlor, poor air cleaner service or overheating AIr CIseasr FuelTank ChokeSpark plug Throttle control Blade Snapper Product Registration Form SNAPPERMcDonough,GA,, 30253 U.S.A

LT200H481BV2, WLT180H421BV2, WLT200H481BV2, LT180H421BV2 specifications

The Snapper LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are versatile riding lawn mowers that cater to homeowners seeking efficient lawn care solutions. Each model is engineered with a combination of power, durability, and advanced features, making them suitable for a variety of yard sizes and terrains.

The Snapper LT180H421BV2 is powered by a robust 18 HP Briggs & Stratton engine, providing reliable performance and ease of use. With a 42-inch cutting deck, this model offers a balance between maneuverability and cutting efficiency. The LT180H421BV2 features a comfortable high-back seat, allowing users to enjoy extended mowing sessions without discomfort. Its steering system is designed for effortless control, making it ideal for navigating around trees and flower beds.

On the other hand, the WLT200H481BV2 boasts a more powerful 20 HP engine, paired with a wide 48-inch cutting deck. This model is equipped with a hydrostatic transmission for smooth acceleration and deceleration, allowing for a responsive and enjoyable mowing experience. The WLT200H481BV2 also includes a dual-blade system, enhancing cutting performance and delivering a clean, manicured finish.

The WLT180H421BV2 combines the advantages of its counterparts with an 18 HP engine and a 42-inch cutting deck. This model is designed for both efficiency and power, making it suitable for homeowners with medium to large lawns. Its compact design enables easy storage and maneuverability in tight spaces, while still offering a comfortable operator experience.

Lastly, the LT200H481BV2 features a powerful 20 HP engine alongside a 48-inch cutting deck, representing the pinnacle of Snapper's residential riding mower technology. It incorporates a premium cut quality with its innovative three-blade system. The hydrostatic transmission ensures smooth operation, allowing users to tackle any lawn challenge effectively.

All these models showcase Snapper’s unwavering commitment to quality and innovation, making lawn maintenance a more efficient and enjoyable task. With comfortable seating, ergonomic controls, and durable construction, the LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are designed for performance and convenience. These mowers truly exemplify the perfect blend of technology and functionality for today's homeowners.