Snapper WLT200H481BV2, LT180H421BV2 Waydowntostart, Starting & Operation 2,3.1. Starting Engine

Page 7

Section 2 - OPERATING INSTRUCTIONS

2,3 STARTING & OPERATION 2,3.1. STARTING ENGINE

1.Take a comfortable position in seat of machine, look around to make sure that the area you are going to mow is clear of people, children and pets. Take note of any stationary obstacles!

NOTE: The interlock system wilI prevent the engine from starting if the blade switch is in the "ON" (up) position or if the dutch/brake pedal is not fully depressed. If the interlock system ever fails to work, DO NOT OPERATE the tractor until the interlock has been repaired.

2.Push blade switch down to the "OFF" position. See

Figure 2.4.PUSH BLADE SWITCH "DOWN" TO

START MACHINE

BLADE

SWITCH

8.Choke engine for cold starting by moving engine speed control to "CHOKE" position. NOTE: Some models are equipped with a separate choke control, located on the dash of the tractor. Pull the control "OUT" to choke position to start a cold engine. Little or no choking wilI be needed when restarting a warm engine. Insert key in switch. Turn key to "START" position to crank engine and hold until engine starts, then release key to "RUN" position. See Figure 2.6.

NOTE: DO NOT crank engine for more than five seconds at a time. This will help prevent the starter from overheating and/or running down the battery. If cranking time is more than five seconds, locate and correct cause of starting problem.

6.After engine starts, release key, move the engine speed control to "FAST" position and allow engine to warm up before proceeding. See Figure 2.6.

FAST

FIGURE 2.4

3.Depress the clutch!brake pedal fully. See Figure 2.5. 4, Move speed control lever to neutral.

SLOW

\

ENGINE

NOTE: The seat interlock will shut off the engine if the

SPEED

KEY

operator gets off the seat without setting the parking brake or if the blades are running. If the interlock ever fails to work, DO NOT OPERATE the tractor until the interlock has been repaired.

CLUTCH/BRAKE

CONTROL

FIGURE 2.6

PEDAL

L

PARK

BRAKE

DOWN

PUSH PEDAL ALL THE

WAYDOWNTOSTART

ENGINE

FIGURE 2,5

Ik WARNING AI

DO NOT leave machine with engine running, Stop[

engine. Stop blades. Set parking brake. Remove key. [

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model Number Explanation Oolo IProtection Against Tipovers Protection for ChildrenOperation MaintenanceTable of Contents Components Controls FamiliarizationOperators Seat Adjustment 1. Front to Rear Adjustment PRE-START ChecklistStarting & Operation 2,3.1. Starting Engine WaydowntostartStopping Wheel Drive Starting & Operation 2,3.2, Starting Wheel Drive3, Stopping Mower Blades Setting Park BrakeCutting Height Adjustment StoppingRolling Hydro Models Rolling Tractor with Engine OFFReverse Lockout Mechanism Override Reverse Lockout Mechanism2, Check Blade Brake Service After First 5 HoursIntroduction Change Engine OILAir Filter Service Every 25 Operating Hours 3.3.1. Check EngineCheck Deck Drive Belt Engine Cooling SystemClutch/Brake Pivot Check Blade BrakeTractor Lubrication Front Wheel Bearings2, Fuel Filter Annually END of Each Season3. Spark Plug 2, Blade Belt Adjustment Engine Adjustments & RepairMower Deck & Component Adjustments 1, Blade Brake AdjustmentFRONT-To-REAR 42 Decks Mower Deck Adjustment LevelnessTOP View of Deck Mower Deck Adjustment Levelness SIDE-To-SIDE 48 DecksOn Next Front To Rear Steering Adjustment Tractor Drive Components 1. Brake Adjustment3, Shifter Adjustment Check for creep in neutral. Start engine. Move Shifter Adjustment4, Traction Drive Belt Adjustment Mower Blade Service Standard Blade Wear LimitsNinja Blade Sharpening Ninja Blade Wear Limits3, Standard Blade Sharpening Traction Drive Belt Replacement 42 Mower Deck Removal 5 & 48 Mower Blade ReplacementDeck Shown View from Underneath Tractor D4SWIVELiiiiiill Sectorplates Spindle Pulleys TOP View Mower Deck 4. Battery Storage Battery Battery RemovalBattery Installation 3. Battery ServiceFive Ball Hydrometer Battery TestingNEW Battery Preparation Chart State of ChargeAvailable Accessories Electrical System Engine Stalls After Probable Cause Corrective ActionRunning Snapper Troubleshooting GuideMower Blades Drive BeltsDisclaimer of Warranty 3YEARLIMITEDWARRANTYIllustration of how dirt can How Maintenance can protect it Cost YOU Moneyi That dirt willCheck OIL Level Before Each START-UP Scuffed wallsAIr CIseasr FuelTank Choke Catlor, poor air cleaner service or overheatingSpark plug Throttle control Blade Snapper Product Registration Form SNAPPERMcDonough,GA,, 30253 U.S.A

LT200H481BV2, WLT180H421BV2, WLT200H481BV2, LT180H421BV2 specifications

The Snapper LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are versatile riding lawn mowers that cater to homeowners seeking efficient lawn care solutions. Each model is engineered with a combination of power, durability, and advanced features, making them suitable for a variety of yard sizes and terrains.

The Snapper LT180H421BV2 is powered by a robust 18 HP Briggs & Stratton engine, providing reliable performance and ease of use. With a 42-inch cutting deck, this model offers a balance between maneuverability and cutting efficiency. The LT180H421BV2 features a comfortable high-back seat, allowing users to enjoy extended mowing sessions without discomfort. Its steering system is designed for effortless control, making it ideal for navigating around trees and flower beds.

On the other hand, the WLT200H481BV2 boasts a more powerful 20 HP engine, paired with a wide 48-inch cutting deck. This model is equipped with a hydrostatic transmission for smooth acceleration and deceleration, allowing for a responsive and enjoyable mowing experience. The WLT200H481BV2 also includes a dual-blade system, enhancing cutting performance and delivering a clean, manicured finish.

The WLT180H421BV2 combines the advantages of its counterparts with an 18 HP engine and a 42-inch cutting deck. This model is designed for both efficiency and power, making it suitable for homeowners with medium to large lawns. Its compact design enables easy storage and maneuverability in tight spaces, while still offering a comfortable operator experience.

Lastly, the LT200H481BV2 features a powerful 20 HP engine alongside a 48-inch cutting deck, representing the pinnacle of Snapper's residential riding mower technology. It incorporates a premium cut quality with its innovative three-blade system. The hydrostatic transmission ensures smooth operation, allowing users to tackle any lawn challenge effectively.

All these models showcase Snapper’s unwavering commitment to quality and innovation, making lawn maintenance a more efficient and enjoyable task. With comfortable seating, ergonomic controls, and durable construction, the LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are designed for performance and convenience. These mowers truly exemplify the perfect blend of technology and functionality for today's homeowners.
Top Page Image Contents