Snapper LT180H421BV2 Shifter Adjustment, Check for creep in neutral. Start engine. Move

Page 21

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool, Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

MOUNTING

BRACKET

MORE TENSION

MOUNTING BOLT

LESS TENSION

MORE TENSION

4.3.3.SHIFTER ADJUSTMENT

(Continued from previous page)

4.

Turn the neutral adjustment

nut 1/4 turn clockwise

to reduce FORWARD creep. Turn the adjustment nut

1/4

turn counter clockwise to

reduce Reverse creep.

Only turn the adjustment nut in 1/4 turn increments.

5.

Check for creep in neutral. Start engine. Move

speed control lever to rear edge of the neutral detent.

LESS TENSION

--MOUNTINGBRACKET

@BELT GUIDE - MAKE CERTAIN BELT GUIDE ORIENTATION IS

MAINTAINED.

Machine should not move. If further adjustment is

required, stop engine and repeat Step 4.

1

STATIONARY IDLER

4,3,4, TRACTION DRIVE BELT ADJUSTMENT

Should a gradual loss of traction be noticed, it may be necessary to adjust the traction drive belt tension. Adjust as follows:

1.Move tractor to a firm, level surface.

2.Turn engine "OFF". Remove key.

3.Remove mowing deck.

4, Remove the traction drive belt stationary idler mounting bolt. See Figure 4.12.

5.Move the stationary idler one hole towards right side of tractor for more belt tension.

NOTE: Note the orientation of belt guide and make certain it remains in the same orientation after moving idler. Should less tension be required move stationary idler towards right side of tractor. See Figure 4.12.

6.Secure stationary idler with mounting bolt.

7.Place spark plug wire onto spark plug. Set park brake. Start engine.

8.Visually inspect traction drive belt for movement. When properly adjusted, the traction drive belt should not have any movement or rotation with the engine running and park brake engaged.

9.Should movement be present, readjust traction drive belt to release belt tension as described in previous instructions.

1_-_MOUNTING BOLT

FIGURE 4.12

4.4 MOWER BLADE SERVICE

4.4.1.(STANDARD) BLADE WEAR LIMITS

All mower blades should be checked for excessive wear

and damage before each use. See Figure 4.13.

NOTCH FORMING

NEAWDE

"c%%%%'GB

NDAN GEROoUNS CoO_DTION, DO

FIGURE 4.13

21

Image 21
Contents Model Number Explanation Oolo IProtection Against Tipovers Protection for ChildrenOperation MaintenanceTable of Contents Components Controls FamiliarizationOperators Seat Adjustment 1. Front to Rear Adjustment PRE-START ChecklistStarting & Operation 2,3.1. Starting Engine WaydowntostartStopping Wheel Drive Starting & Operation 2,3.2, Starting Wheel DriveCutting Height Adjustment Setting Park BrakeStopping 3, Stopping Mower BladesRolling Hydro Models Rolling Tractor with Engine OFFReverse Lockout Mechanism Override Reverse Lockout MechanismIntroduction Service After First 5 HoursChange Engine OIL 2, Check Blade BrakeCheck Deck Drive Belt Service Every 25 Operating Hours 3.3.1. Check EngineEngine Cooling System Air FilterTractor Lubrication Check Blade BrakeFront Wheel Bearings Clutch/Brake PivotAnnually END of Each Season 2, Fuel Filter3. Spark Plug Mower Deck & Component Adjustments Engine Adjustments & Repair1, Blade Brake Adjustment 2, Blade Belt AdjustmentFRONT-To-REAR 42 Decks Mower Deck Adjustment LevelnessMower Deck Adjustment Levelness SIDE-To-SIDE 48 Decks TOP View of DeckOn Next Front To Rear Tractor Drive Components 1. Brake Adjustment Steering Adjustment3, Shifter Adjustment 4, Traction Drive Belt Adjustment Shifter AdjustmentMower Blade Service Standard Blade Wear Limits Check for creep in neutral. Start engine. MoveNinja Blade Wear Limits Ninja Blade Sharpening3, Standard Blade Sharpening 5 & 48 Mower Blade Replacement Traction Drive Belt Replacement 42 Mower Deck RemovalDeck Shown View from Underneath Tractor D4SWIVELiiiiiill Sectorplates Spindle Pulleys TOP View Mower Deck Battery Installation Battery Battery Removal3. Battery Service 4. Battery StorageNEW Battery Preparation Battery TestingChart State of Charge Five Ball HydrometerAvailable Accessories Electrical System Probable Cause Corrective Action Engine Stalls AfterRunning Snapper Troubleshooting GuideMower Blades Drive BeltsDisclaimer of Warranty 3YEARLIMITEDWARRANTYIllustration of how dirt can How Maintenance can protect it Cost YOU Moneyi That dirt willCheck OIL Level Before Each START-UP Scuffed wallsCatlor, poor air cleaner service or overheating AIr CIseasr FuelTank ChokeSpark plug Throttle control Blade Snapper Product Registration Form SNAPPERMcDonough,GA,, 30253 U.S.A

LT200H481BV2, WLT180H421BV2, WLT200H481BV2, LT180H421BV2 specifications

The Snapper LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are versatile riding lawn mowers that cater to homeowners seeking efficient lawn care solutions. Each model is engineered with a combination of power, durability, and advanced features, making them suitable for a variety of yard sizes and terrains.

The Snapper LT180H421BV2 is powered by a robust 18 HP Briggs & Stratton engine, providing reliable performance and ease of use. With a 42-inch cutting deck, this model offers a balance between maneuverability and cutting efficiency. The LT180H421BV2 features a comfortable high-back seat, allowing users to enjoy extended mowing sessions without discomfort. Its steering system is designed for effortless control, making it ideal for navigating around trees and flower beds.

On the other hand, the WLT200H481BV2 boasts a more powerful 20 HP engine, paired with a wide 48-inch cutting deck. This model is equipped with a hydrostatic transmission for smooth acceleration and deceleration, allowing for a responsive and enjoyable mowing experience. The WLT200H481BV2 also includes a dual-blade system, enhancing cutting performance and delivering a clean, manicured finish.

The WLT180H421BV2 combines the advantages of its counterparts with an 18 HP engine and a 42-inch cutting deck. This model is designed for both efficiency and power, making it suitable for homeowners with medium to large lawns. Its compact design enables easy storage and maneuverability in tight spaces, while still offering a comfortable operator experience.

Lastly, the LT200H481BV2 features a powerful 20 HP engine alongside a 48-inch cutting deck, representing the pinnacle of Snapper's residential riding mower technology. It incorporates a premium cut quality with its innovative three-blade system. The hydrostatic transmission ensures smooth operation, allowing users to tackle any lawn challenge effectively.

All these models showcase Snapper’s unwavering commitment to quality and innovation, making lawn maintenance a more efficient and enjoyable task. With comfortable seating, ergonomic controls, and durable construction, the LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are designed for performance and convenience. These mowers truly exemplify the perfect blend of technology and functionality for today's homeowners.