Snapper WLT200H481BV2, WLT180H421BV2 important safety instructions Front To Rear

Page 19

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.2.5.MOWER DECK ADJUSTMENT (LEVELNESS) SIDE-To-SIDE (48" Decks)

(Continued From Previous Page)

6.Remove both hair pins and washers from swivel

located on rear lift rods and pull rod out of deck brackets.

7.Rotate swivels on both sides up or down to achieve the proper levelness. See Figure 4.8.

8.Reinstall swivel into deck bracket. Reinstall washers and hair pins.

9.Tighten nut and bolt on front lift arm securely.

4.2.6.MOWER DECK ADJUSTMENT (LEVELNESS)

(FRONT To REAR)

Before making deck leveling adjustments, check the tire pressure. Add or release air as needed to bring pressure to 12 PSi in front and 12 PSI in rear tires. If tires are properly inflated and mowing is still uneven, check side-to-side deck levelness first then proceed

to front to rear adjustment. Adjust front to rear deck levelness as follows:

1.Place machine on a smooth level surface.

2.Rotate outside blades so tips are pointed to the front and rear of deck. Measure the distance from

blade tips to floor. The distance should be the same, or the rear no more than 1/4" higher than the front. If the rear blade tip is lower or is more than 1/4" higher than

the front, proceed to next Step for adjustment.

3.Remove the hair pin & washer from swivel located on lift rod. Remove swiveltIift rod from hanger bracket.

4.Rotate swivel up or down to achieve the proper levelness.

5.Reinstall swivel!lift rod into hanger bracket. Reinstall washer & hair pin to secure swivel to hanger bracket. See Figure 4.8.

/

LIFT ROD

REMOVE WASHER & HAIR PIN

&ROTATE. SWIVEL UP OR DOWN

REMOVE WASHER & HAIR PIN

_,,---&ROTATE SWIVEL UP OR DOWN

\FRONT

\

\

 

LIFT

 

 

\

 

ROD

DECK

\

\

\

 

BRACKET

 

 

 

\\

\ \

\ \

\ \

\\

\\

\ \

\ \

\

FIGURE 4.8

"-

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model Number Explanation Oolo IProtection Against Tipovers Protection for ChildrenOperation MaintenanceTable of Contents Components Controls FamiliarizationOperators Seat Adjustment 1. Front to Rear Adjustment PRE-START ChecklistStarting & Operation 2,3.1. Starting Engine WaydowntostartStopping Wheel Drive Starting & Operation 2,3.2, Starting Wheel Drive3, Stopping Mower Blades Setting Park BrakeCutting Height Adjustment StoppingRolling Hydro Models Rolling Tractor with Engine OFFReverse Lockout Mechanism Override Reverse Lockout Mechanism2, Check Blade Brake Service After First 5 HoursIntroduction Change Engine OILAir Filter Service Every 25 Operating Hours 3.3.1. Check EngineCheck Deck Drive Belt Engine Cooling SystemClutch/Brake Pivot Check Blade BrakeTractor Lubrication Front Wheel Bearings2, Fuel Filter Annually END of Each Season3. Spark Plug 2, Blade Belt Adjustment Engine Adjustments & RepairMower Deck & Component Adjustments 1, Blade Brake AdjustmentFRONT-To-REAR 42 Decks Mower Deck Adjustment LevelnessTOP View of Deck Mower Deck Adjustment Levelness SIDE-To-SIDE 48 DecksOn Next Front To Rear Steering Adjustment Tractor Drive Components 1. Brake Adjustment3, Shifter Adjustment Check for creep in neutral. Start engine. Move Shifter Adjustment4, Traction Drive Belt Adjustment Mower Blade Service Standard Blade Wear LimitsNinja Blade Sharpening Ninja Blade Wear Limits3, Standard Blade Sharpening Traction Drive Belt Replacement 42 Mower Deck Removal 5 & 48 Mower Blade ReplacementDeck Shown View from Underneath Tractor D4SWIVELiiiiiill Sectorplates Spindle Pulleys TOP View Mower Deck 4. Battery Storage Battery Battery RemovalBattery Installation 3. Battery ServiceFive Ball Hydrometer Battery TestingNEW Battery Preparation Chart State of ChargeAvailable Accessories Electrical System Engine Stalls After Probable Cause Corrective ActionRunning Snapper Troubleshooting GuideMower Blades Drive BeltsDisclaimer of Warranty 3YEARLIMITEDWARRANTYIllustration of how dirt can How Maintenance can protect it Cost YOU Moneyi That dirt willCheck OIL Level Before Each START-UP Scuffed wallsAIr CIseasr FuelTank Choke Catlor, poor air cleaner service or overheatingSpark plug Throttle control Blade Snapper Product Registration Form SNAPPERMcDonough,GA,, 30253 U.S.A

LT200H481BV2, WLT180H421BV2, WLT200H481BV2, LT180H421BV2 specifications

The Snapper LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are versatile riding lawn mowers that cater to homeowners seeking efficient lawn care solutions. Each model is engineered with a combination of power, durability, and advanced features, making them suitable for a variety of yard sizes and terrains.

The Snapper LT180H421BV2 is powered by a robust 18 HP Briggs & Stratton engine, providing reliable performance and ease of use. With a 42-inch cutting deck, this model offers a balance between maneuverability and cutting efficiency. The LT180H421BV2 features a comfortable high-back seat, allowing users to enjoy extended mowing sessions without discomfort. Its steering system is designed for effortless control, making it ideal for navigating around trees and flower beds.

On the other hand, the WLT200H481BV2 boasts a more powerful 20 HP engine, paired with a wide 48-inch cutting deck. This model is equipped with a hydrostatic transmission for smooth acceleration and deceleration, allowing for a responsive and enjoyable mowing experience. The WLT200H481BV2 also includes a dual-blade system, enhancing cutting performance and delivering a clean, manicured finish.

The WLT180H421BV2 combines the advantages of its counterparts with an 18 HP engine and a 42-inch cutting deck. This model is designed for both efficiency and power, making it suitable for homeowners with medium to large lawns. Its compact design enables easy storage and maneuverability in tight spaces, while still offering a comfortable operator experience.

Lastly, the LT200H481BV2 features a powerful 20 HP engine alongside a 48-inch cutting deck, representing the pinnacle of Snapper's residential riding mower technology. It incorporates a premium cut quality with its innovative three-blade system. The hydrostatic transmission ensures smooth operation, allowing users to tackle any lawn challenge effectively.

All these models showcase Snapper’s unwavering commitment to quality and innovation, making lawn maintenance a more efficient and enjoyable task. With comfortable seating, ergonomic controls, and durable construction, the LT180H421BV2, WLT200H481BV2, WLT180H421BV2, and LT200H481BV2 are designed for performance and convenience. These mowers truly exemplify the perfect blend of technology and functionality for today's homeowners.
Top Page Image Contents