Snapper CRP216019KWV important safety instructions Service Schedule, Maintenance Parts

Page 22

SERVICE SCHEDULE

SERVICE SCHEDULE

ITEM	SERVICE PERFORMED	REF.	EACH	5		25	50	100	EACH
			USE	HRS		HRS	HRS	HRS	SEASON
Engine Oil	Check Oil Level	Page 7	X

	Initial Oil Change	Page 12		X

	Periodic Oil Change	Page 13				X*

Air Pre-Cleaner	Clean Sponge Element	Engine Manual				X**

Air Cleaner	Clean or Replace	Engine Manual				X**

Spark Plug	Replace	Engine Manual						X

Engine Cooling	Clean Shroud & Fins	Engine Manual						X**
System
Drive Belts	Check For Wear And	Page 19-20				X	X		X
	Tension
Mower Blade	Check For Wear, Damage	Page 14-15	X
	& Replacement
Mower Deck	Clean Debris	Page 7	X
	Accumulation
Transmission	Check Grease Level	Pages 12-13				X			X
Grease
	Periodic Grease Check	Pages 12-13							X

Drive Disc	Check for Wear Damage	Page 16-18					X
	& Replacement
*Change oil every 25 hours when operating under heavy load or high temperatures.
**Clean more often under dusty conditions or when air debris is present
4.6 MAINTENANCE/REPLACEMENT PARTS

MAINTENANCE PARTS

Engine Speed Control (Kawasaki Engines)	7074138
Blade Control Cable (Kawasaki Engines)	7074141
Clutch Pull Cable (See Parts Manual)	7034604
Cutter Blade (Air Lift Compatible)	7019795
Cutter Blade (Mulching)	7017168
Cutter Blade (Not Air Lift Compatible)	7026691
Cutter Blade (Ninja - Quad Edge)	7026407
Wheel Drive Pulley to Transmission Pulley Belt	7012354
Engine to Drive Disc Belt	7046784
Cantilever Drive Tire Assembly	7073528
Rubber Drive Tire	7010927
Parts Manual for 21” Steel Deck Recycling Walk Mower Commercial Series 19	7006156

22

Image 22

Contents PROPELLED MODELS Safety Instructions & Operator’s Manual for21” STEEL DECK RECYCLING WALK MOWERS COMMERCIAL MODELS SERIES CRP216019KWVSLOPE OPERATION IMPORTANT SAFETY INSTRUCTIONSPROTECTION FOR CHILDREN PREPARATIONMAINTENANCE AND STORAGE OPERATIONIMPORTANT SAFETY INSTRUCTIONS TABLE OF CONTENTS 1.1 INTRODUCTION Section 1 - FAMILIARIZATIONENGINE SPEED CONTROL 1.2 NOMENCLATURE2.1 PRE-START CHECK LIST Section 2 - OPERATING INSTRUCTIONS2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE 2.2.3. PROPELLING MOWER TO REMOVE RECYCLING COVER 2.7 INSTALLATION OF SIDE DISCHARGE DEFLECTOR2.6 RECYCLING OPERATION Continued Next PageBOLT WITH REPLACEMENTROUTE RECOIL ROPE AROUND PULLEY SECURE ADAPTER TO DECK THREAD SLEEVE1. Grasp bag connector and bag handle as shown. See Figure Section 3 - MAINTENANCE IMPORTANT Drain fuel tank before tipping mower Section 4 - REPAIR & ADJUSTMENTS 4. Sharpen blade on a grinding wheel at an angle of 1. Grease on drive disc causing slippage 7. Reinstall driven disc spring to driven disc assembly MACHINE BEARINGREMOVE FOUR SCREWSTo replace the bearing on the pulley end of the hex Remove the driven disc. Refer to Section PROBABLE CAUSE TROUBLESHOOTINGPROBLEM CORRECTIVE ACTIONSERVICE SCHEDULE MAINTENANCE PARTS2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Page Page Page Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone