Snapper CRP216019KWV important safety instructions Table Of Contents

Page 5

TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS	2 - 4
TABLE OF CONTENTS	5
SECTION 1 - FAMILIARIZATION	6
SECTION 2 - OPERATING INSTRUCTIONS	7-10
Pre-start Checklist	7
Starting & Stopping Engine & Blade	7
Starting & Stopping Wheel Drive	8
Handle Height Adjustment	8
Cutting Height Adjustment	8
Recycling Operation	9
Removing Recycling Cover	9
Installation of Discharge Deflector	9
Installation of Grass Bag	10-11
SECTION 3 - MAINTENANCE INSTRUCTIONS	12-13
Change Engine Oil	12
Check Transmission Grease	12
Check Mower Blade	13
Check Engine Drive Belt	13
Check Transmission Poly-V Belt	13
Service - Annually	13
Engine	13
Air Filter	13
Engine Oil	13
Storage Procedure	13
SECTION 4 - ADJUSTMENTS AND REPAIR	14-20
Mower Blade Replacement	14
Blade Sharpening	14-15
Wheel Drive Control Adjustment	15
Driven and Drive Disc Service	16-19
Cleaning Drive Disc and Driven Disc	16
Drive Spring Repair/Replacement	16
Driven Disc Adjustment	16-17
Driven Disc Rubber Ring Replacement	17-18
Driven Disc Bearing Replacement	18
Hex Shaft Bearing Replacement	19
Belt Service	19-20
Engine Drive Belt Replacement	19-20
Transmission Poly-V Belt Replacement	20
TROUBLESHOOTING	21
SERVICE SCHEDULE	22
Maintenance/Replacement Parts	22
WARRANTY	23
PRIMARY MAINTENANCE	24-27
PRODUCT REGISTRATION FORM	28

! IMPORTANT !

The figures and illustrations in this manual are provided for reference only and may differ from your specific model. Contact your local SNAPPER dealer if you have questions.

5

Image 5

Contents 21” STEEL DECK RECYCLING WALK MOWERS COMMERCIAL MODELS SERIES Safety Instructions & Operator’s Manual forPROPELLED MODELS CRP216019KWVPROTECTION FOR CHILDREN IMPORTANT SAFETY INSTRUCTIONSSLOPE OPERATION PREPARATIONOPERATION MAINTENANCE AND STORAGEMAINTENANCE AND STORAGE TABLE OF CONTENTS ENGINE SPEED CONTROL Section 1 - FAMILIARIZATION1.1 INTRODUCTION 1.2 NOMENCLATURE2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE Section 2 - OPERATING INSTRUCTIONS2.1 PRE-START CHECK LIST 2.2.3. PROPELLING MOWER 2.6 RECYCLING OPERATION 2.7 INSTALLATION OF SIDE DISCHARGE DEFLECTORTO REMOVE RECYCLING COVER Continued Next PageROUTE RECOIL ROPE AROUND PULLEY SECURE ADAPTER TO DECK REPLACEMENTBOLT WITH THREAD SLEEVE1. Grasp bag connector and bag handle as shown. See Figure Section 3 - MAINTENANCE IMPORTANT Drain fuel tank before tipping mower Section 4 - REPAIR & ADJUSTMENTS 4. Sharpen blade on a grinding wheel at an angle of 1. Grease on drive disc causing slippage 7. Reinstall driven disc spring to driven disc assembly REMOVE FOUR BEARINGMACHINE SCREWSTo replace the bearing on the pulley end of the hex Remove the driven disc. Refer to Section PROBLEM TROUBLESHOOTINGPROBABLE CAUSE CORRECTIVE ACTIONMAINTENANCE PARTS SERVICE SCHEDULE2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Page Page Page Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone