Snapper CRP216019KWV 21” STEEL DECK RECYCLING WALK MOWERS COMMERCIAL MODELS SERIES

Page 32

Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone: (1-800-935-2967).

Safety Instructions & Operator’s Manual for

21” STEEL DECK RECYCLING WALK MOWERS COMMERCIAL MODELS SERIES 19

IMPORTANT

Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone: (1-800-935-2967).

WARNING

BATTERY POSTS, TERMINALS AND RELATED ACCESSORIES CONTAIN LEAD AND LEAD COMPOUNDS, CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING.

WARNING

ENGINE EXHAUST, SOME OF ITS CONSTITUENTS, AND CERTAIN VEHICLE COMPONENTS CONTAIN OR EMIT CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER OR OTHER REPRODUCTIVE HARM.

COPYRIGHT © 2006

SNAPPER – A DIVISION OF SIMPLICITY MFG., INC.

ALL RIGHTS RESERVED

MANUAL No. 7100372 (I.R. 1/11/2006)

TP 100-5114-IR-CW-N

32

Image 32

Contents Safety Instructions & Operator’s Manual for 21” STEEL DECK RECYCLING WALK MOWERS COMMERCIAL MODELS SERIESPROPELLED MODELS CRP216019KWVIMPORTANT SAFETY INSTRUCTIONS PROTECTION FOR CHILDRENSLOPE OPERATION PREPARATIONMAINTENANCE AND STORAGE OPERATIONIMPORTANT SAFETY INSTRUCTIONS TABLE OF CONTENTS Section 1 - FAMILIARIZATION ENGINE SPEED CONTROL1.1 INTRODUCTION 1.2 NOMENCLATURE2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE Section 2 - OPERATING INSTRUCTIONS2.1 PRE-START CHECK LIST 2.2.3. PROPELLING MOWER 2.7 INSTALLATION OF SIDE DISCHARGE DEFLECTOR 2.6 RECYCLING OPERATIONTO REMOVE RECYCLING COVER Continued Next PageREPLACEMENT ROUTE RECOIL ROPE AROUND PULLEY SECURE ADAPTER TO DECKBOLT WITH THREAD SLEEVE1. Grasp bag connector and bag handle as shown. See Figure Section 3 - MAINTENANCE IMPORTANT Drain fuel tank before tipping mower Section 4 - REPAIR & ADJUSTMENTS 4. Sharpen blade on a grinding wheel at an angle of 1. Grease on drive disc causing slippage 7. Reinstall driven disc spring to driven disc assembly BEARING REMOVE FOURMACHINE SCREWSTo replace the bearing on the pulley end of the hex Remove the driven disc. Refer to Section TROUBLESHOOTING PROBLEMPROBABLE CAUSE CORRECTIVE ACTIONSERVICE SCHEDULE MAINTENANCE PARTS2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Page Page Page Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone