Snapper CRP216019KWV Repair & Adjustments, Reinstall driven disc spring to driven disc assembly

Page 17
7.Reinstall driven disc spring to driven disc assembly.

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.3.3.DRIVEN DISC ADJUSTMENT (Continued From Previous Page)

2.Remove driven disc spring from driven disc assembly. Also remove pin and washer from transfer rod, and remove end of transfer rod from hole in driven disc assembly. See Figure 4.9.

DRIVEN DISC

ASSEMBLY

DRIVE

DISC

REMOVE

DRIVEN DISC

SPRING

REMOVE END

REMOVE

OF TRANSFER

ROD FROM

PIN AND

DRIVEN DISC

WASHER

ASSY

FROM ROD

FIGURE 4.9

3.Slide driven disc assembly over to 1/8” from outside edge of drive disc. See Figure 4.10.

4.Loosen jam nut securing transfer rod to ball joint on pivot bracket. See Figure 4.11.

5.Turn rod in or out of ball joint until end of rod aligns with hole in driven disc assembly from which rod was removed. NOTE: Do not move pivot bracket.

6.Reinstall rod as removed in step 2. Move ground speed control to ‘slow’ position, then back to ‘fast’ position. Recheck the 1/8” measurement described previously. Readjust as needed. Tighten nut when finished.

7.Reinstall driven disc spring to driven disc assembly.

1/8” MEASUREMENT TO OUTSIDE EDGE OF DRIVE DISC

DRIVE

SLIDE DRIVENDISC DISC ASSEMBLY

TOWARD OUTSIDE EDGE

OUTSIDE

EDGE

FIGURE 4.10

BALL JOINT

LOOSEN NUT

 

TURN ROD IN

PIVOT

OR OUT UNTIL

BRACKET

END ALIGNS

 

WITH HOLE

FIGURE 4.11

(Continued On Next Page)

4.3.4. Replacing Driven Disc Rubber Ring

If the rubber is badly chunked or worn it must be replaced. Install new Rubber Ring as follows:

1.Remove pin and washer from transfer rod, and remove end of transfer rod from hole in driven disc assembly. See Figure 4.9.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 21” STEEL DECK RECYCLING WALK MOWERS COMMERCIAL MODELS SERIES Safety Instructions & Operator’s Manual forPROPELLED MODELS CRP216019KWVPROTECTION FOR CHILDREN IMPORTANT SAFETY INSTRUCTIONSSLOPE OPERATION PREPARATIONOPERATION MAINTENANCE AND STORAGEMAINTENANCE AND STORAGE TABLE OF CONTENTS ENGINE SPEED CONTROL Section 1 - FAMILIARIZATION1.1 INTRODUCTION 1.2 NOMENCLATURE2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE Section 2 - OPERATING INSTRUCTIONS2.1 PRE-START CHECK LIST 2.2.3. PROPELLING MOWER 2.6 RECYCLING OPERATION 2.7 INSTALLATION OF SIDE DISCHARGE DEFLECTORTO REMOVE RECYCLING COVER Continued Next PageROUTE RECOIL ROPE AROUND PULLEY SECURE ADAPTER TO DECK REPLACEMENTBOLT WITH THREAD SLEEVE1. Grasp bag connector and bag handle as shown. See Figure Section 3 - MAINTENANCE IMPORTANT Drain fuel tank before tipping mower Section 4 - REPAIR & ADJUSTMENTS 4. Sharpen blade on a grinding wheel at an angle of 1. Grease on drive disc causing slippage 7. Reinstall driven disc spring to driven disc assembly REMOVE FOUR BEARINGMACHINE SCREWSTo replace the bearing on the pulley end of the hex Remove the driven disc. Refer to Section PROBLEM TROUBLESHOOTINGPROBABLE CAUSE CORRECTIVE ACTIONMAINTENANCE PARTS SERVICE SCHEDULE2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Page Page Page Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone
Top Page Image Contents