Snapper CRP216019KWV Operating Instructions, Recycling Operation, To Remove Recycling Cover

Page 9
2.6 RECYCLING OPERATION

Section 2 - OPERATING INSTRUCTIONS

2.6 RECYCLING OPERATION

NOTE: For best recycling results, cut up to a maximum of 1/3 of grass blade length and recycle ONLY when grass is dry.

1.Set all wheels in the highest cutting position (Notch 7). Refer to Section “Cutting Height Adjustment”.

2.Move engine speed control to “FAST” (Rabbit) position.

3.Move ground speed control to slowest speed setting.

4.Proceed mowing slowly. If grass is very dense, lower each rear wheel latch one notch lower than the front wheel latches to improve recycling performance.

NOTE: The recycling cover is designed to remain on the machine at all times, unless alternate discharge operations are desired, such as side

2.7INSTALLATION OF SIDE DISCHARGE DEFLECTOR

STEP 1: Remove recycling cover. Refer to Section “Recycling Operation”.

STEP 2: Install deflector to deck in place of recycling

cover, making sure that: 1) hole on outside front of deflector fits onto stud in front of discharge opening where front of recycling cover was originally installed, 2) slot on top of deflector slips under restraining nut on top of deck (under right front corner of engine), and 3) slot on inside rear of deflector slips onto stud behind rear of discharge opening, where rear of recycling cover was originally secured. See Figure 2.10. Install internal/external tooth lock washers and knob nuts onto studs and tighten securely.

discharging or bagging. Recycling cover can be removed to accommodate alternate discharge components.

TO REMOVE RECYCLING COVER:

Remove knob nuts and internal/external tooth lock washers securing rear of recycling cover to mower deck. Remove cover. See Figure 2.9.

2.7INSTALLATION OF SIDE DISCHARGE DEFLECTORREMOVE

KNOB NUTS

AND LOCK

WASHERS

FIGURE 2.9

REAR SLOT OVER STUD ; INSTALL LOCK WASHER AND KNOB NUT

FRONT

SLOT

UNDER NUT

FRONT HOLE

OVER STUD;

INSTALL LOCK

WASHER AND

KNOB NUT

FIGURE 2.10

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

(Continued Next Page)

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 21” STEEL DECK RECYCLING WALK MOWERS COMMERCIAL MODELS SERIES Safety Instructions & Operator’s Manual forPROPELLED MODELS CRP216019KWVPROTECTION FOR CHILDREN IMPORTANT SAFETY INSTRUCTIONSSLOPE OPERATION PREPARATIONOPERATION MAINTENANCE AND STORAGEMAINTENANCE AND STORAGE TABLE OF CONTENTS ENGINE SPEED CONTROL Section 1 - FAMILIARIZATION1.1 INTRODUCTION 1.2 NOMENCLATURESection 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE 2.2.3. PROPELLING MOWER 2.6 RECYCLING OPERATION 2.7 INSTALLATION OF SIDE DISCHARGE DEFLECTORTO REMOVE RECYCLING COVER Continued Next PageROUTE RECOIL ROPE AROUND PULLEY SECURE ADAPTER TO DECK REPLACEMENTBOLT WITH THREAD SLEEVE1. Grasp bag connector and bag handle as shown. See Figure Section 3 - MAINTENANCE IMPORTANT Drain fuel tank before tipping mower Section 4 - REPAIR & ADJUSTMENTS 4. Sharpen blade on a grinding wheel at an angle of 1. Grease on drive disc causing slippage 7. Reinstall driven disc spring to driven disc assembly REMOVE FOUR BEARINGMACHINE SCREWSTo replace the bearing on the pulley end of the hex Remove the driven disc. Refer to Section PROBLEM TROUBLESHOOTINGPROBABLE CAUSE CORRECTIVE ACTIONMAINTENANCE PARTS SERVICE SCHEDULE2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Page Page Page Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone
Top Page Image Contents