Snapper 285Z manual Operation, General Operating Safety, Checks Before Starting

Page 14

Operation

General Operating Safety

Before first time operation:

•Be sure to read all information in the Safety and Operation sections before attempting to operate this rider and mower.

•Become familiar with all of the controls and how to stop the unit.

•Drive in an open area without mowing to become accus- tomed to driving the unit.

Checks Before Starting

•Check that the crankcase is filled to full mark on dipstick (A, Figure 1 - located under engine cover). See the engine owner’s manual for instructions and oil recommendations.

•Make sure all nuts, bolts, screws and pins are in place and secure.

•Adjust the seat position (B), and make certain you can reach all controls from the operator’s position.

•Fill the fuel tank (C) with fresh fuel. Refer to the engine owner’s manual for fuel recommendations.

WARNING

 

 

 

Never operate on slopes greater than 18 percent (10°).

B

Select slow ground speed before driving onto a slope. Use

 

extra caution when operating on slopes with a rear-mounted

 

grass catcher.

Reproductrider. This rideriohas na zero turning radius and the rear

spills.

Mow up and down slopes, not across the face, use caution

 

when changing directions and DO NOT START OR STOP ON

 

SLOPE.

 

 

C

 

 

 

A

WARNING

 

 

 

Never allow passengers to ride on the unit.

 

 

Before leaving the operator’s position for any reas

n, l ck

 

the ground speed levers in the START/PARK position,

 

engage the parking brake, disengage the PTO, stop the

 

engine and remove the key.

 

 

 

To reduce fire hazard, keep the engine, rider and mower f ee

Figure 1. Pre-Start Checks

of grass, leaves and excess grease. Do not stop or

ark rider

 

over dry leaves, grass or combustible materials.

 

WARNING

Gasoline is highly flammable and must be handl

with

care. Never fill the tank when the engine is still hot from

Do not load this zero-turn rider on a trailer or truck using

recent operation. Do not allow open flame, smoking or

two separate ramps. Only use a single ramp that is at least

matches in the area. Avoid over-filling and wipe up any

one foot wider than the width of the rear wheels of this

 

 

 

 

 

 

wheels could fall off the ramps, or the rider could tip over

WARNING

 

 

injuring the operator or bystanders.

 

 

 

If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES & CONTROLS section, do so now.

Do NOT attempt to operate the rider without first becoming familiar with the location and function of ALL controls.

14

www.Snapper.com

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Not For Manual No Rev ‘A’, 6/14/2010Unit ID Tag Service, or information you Must have these numb rsIdentification Numbers Table of Contents Operator’s manual contains important safety information Operator SafetyOperating Safety Read the ManualMoving Parts Slope OperationThrown Objects Enclosed Areas Fuel and MaintenanceRetaining Walls, Drop-offs, and Water Protection for Children Protection Against Tipovers Preparation Protection Against TipoversEmissions Preparation OperationSafe Handling of Gasoline Towing Maintenance Decal, Warning Safety and Instructional DecalsDecal, Caution Safety Interlock System Operational Safety ChecksGround Speed Levers Features and ControlsControl Functions PTO Switch Hour Meter Ignition SwitchMower Cutting Height Adjustment Switch Seat Adjustment LeverChecks Before Starting General Operating SafetyOperation Before first time operationMowing Starting the EngineStopping the Rider and Engine Forward Reverse Travel Zero Turn Smooth Travel Driving PracticeForward Travel Practice Reverse Travel Practice Levers GraduallyAllows you to turn around at the end of a cutting Practice Turning In PlaceTurning In-Place Attaching a Trailer 20’ 6mMaintenance Maintenance ChartFuel Filter Engine MaintenanceAfter installation Ver-filling and wipe up anyNever store the unit with fuel in an enclosed, poorly Precautions may result in serious injury or deathStorage Source such as a furnace, water heater, etc. and cause anSeat Adjustments Adjustments and ServiceSpeed Balancing Adjustment Ground Speed Lever AdjustmentRemoval Cutting Height AdjustmentMower Removal and Installation Tion indicated by the arrow, and remove the mower beltWith a washer and hairpin clip a InstallationTion indicated, and install the belt onto the PTO pulley as Washer and hairpin clip aPerform the following procedure if the clutch is slipping PTO Clutch AdjustmentPTO Clutch Adjustment Blade Brake CheckMower Deck Leveling Right side shown, left side hiddenFig re 27. Balancing The Blade Remove mower deck see Mower Deck RemovalDamaged, it must be replaced Front caster wheel axles LubricationGrease OilBattery Maintenance Battery ChargingTroubleshooting Troubleshooting the RiderTroubleshooting Warranty Warranty PeriodNot For Not For Not For Replacement Parts SpecificationsDimensions Chassis Maintenance Items

285Z specifications

The Snapper 285Z is a robust and versatile zero-turn mower designed for efficient lawn care, making it an excellent choice for both homeowners and landscaping professionals. Renowned for its reliability and performance, the Snapper 285Z stands out in the competitive market of outdoor power equipment.

One of the main features of the Snapper 285Z is its powerful engine options. Equipped with a high-performance, commercial-grade engine, it delivers outstanding torque and power to tackle various mowing conditions. This ensures that users can easily mow through tough grass and uneven terrains without bogging down. The engine is designed for easy starting and smooth operation, contributing to the overall user experience.

The patented zero-turn technology of the Snapper 285Z allows for unparalleled maneuverability. With its dual-lever steering system, operators can easily turn in tight spaces and navigate around obstacles with confidence. This feature significantly reduces mowing time and enhances efficiency, making it ideal for residential lawns, commercial properties, and intricate landscaping designs.

The Snapper 285Z also boasts an adjustable cutting deck, with widths typically ranging from 48 to 52 inches, allowing users to choose the perfect size for their mowing needs. The deck is constructed from durable steel, ensuring longevity and resistance to wear and tear. Additionally, the cutting height can be quickly adjusted, offering versatility for different grass types and seasonal growth patterns.

Another notable characteristic of the Snapper 285Z is its user-friendly design. With a comfortable seat, ergonomic controls, and an easy-to-read instrument panel, it promotes a pleasant mowing experience. The mower is also equipped with an electric start feature, eliminating the need for pull cords and enhancing ease of use.

Safety is a top priority with the Snapper 285Z, featuring roll-over protection and safety switches that ensure the mower shuts down when the operator leaves the seat. This attention to safety not only protects the user but also adds to the mower's overall reliability.

In summary, the Snapper 285Z combines powerful performance, innovative technology, and user-focused features to offer an exceptional mowing experience. Its zero-turn capability, durable construction, and adjustable cutting options make it a top choice for anyone looking to maintain a beautiful lawn efficiently.
Top Page Image Contents