Snapper Troubleshooting Guide for Lawn Mower Drive Belt Issues
Page 31

 

 

 

 

 

 

Troubleshooting

Rider Troubleshooting Continued.

 

 

 

 

 

PROBLEM

CAUSE

 

 

REMEDY

Engine runs, but rider will

1.

Transmission(s) disengaged.

1.

Unlock roll release rod(s).

not drive.

2.

Belt is broken.

 

2.

See authorized service dealer.

 

3.

Drive belt slips.

 

3.

See authorized service dealer.

 

4.

Brake is not fully released.

4.

See authorized service dealer.

 

5.

Internal transmission problem

5.

See authorized service dealer

 

 

 

 

 

Rider drive belt slips.

1.

Pulleys or belt greasy or oily.

1.

Clean as required.

 

2.

Belt stretched or worn.

2.

See authorized service dealer.

Brake will not hold.

1.

Brake components worn or damaged.

1.

See authorized service dealer.

 

2.

Internal transmission problem.

2.

See authorized service dealer.

 

 

 

 

 

Rider steers or handles poorly.

1.

Steering linkage is loose.

1.

Check and tighten any loose connections.

 

2.

Improper tire inflation.

2.

See Maintenance Section.

 

 

 

 

 

 

 

Troubleshooting the Mower

 

 

 

 

 

 

PROBLEM

CAUSE

 

 

REMEDY

Mower will not raise.

1.

Mower deck not properly installed.

1.

See Mower Removal and Installation.

 

Reproductionof balance.See Maintenance Section.

 

2.

Deck lift component(s) damaged.

2.

See authorized service dealer.

Mower cut is uneven.

1.

Mower not leveled p ope ly.

1.

See Mower Adjustment.

 

2.

Rider tires n

t inflated

2.

See Mai te a ce Section.

 

 

equally or pr

perly.

 

 

Mower cut is rough looking.

1.

Engine speed

 

sl w.

1.

Set engine speed control to FAST.

 

2.

Ground speed oo

ast.

2.

Decrease ground speed.

 

3.

Blades are dull.

 

3.

Sharpen or replace blades.

 

 

 

 

 

 

See Servicing the Mower Blades.

 

4.

M wer drive belt slipping

4.

See authorized service dealer.

 

 

because it is

ily or worn.

 

 

 

5.

Blades not properly fastened

5.

See Servicing the Mower Blades.

 

 

to spindles.

 

 

 

 

Engine stalls easily with

1.

Engine speed

 

sl w.

1.

Set engine speed control to FAST.

mower engaged.

2.

Ground s eed t

fast.

2.

Decrease ground speed.

 

3.

Cutting height set too low.

3.

Cut tall grass at maximum cutting

 

 

 

 

 

 

height during first pass.

 

4.

Discharge chute jamming

4.

Cut grass with discharge pointing toward

 

 

with cut grass.

 

 

previously cut area.

 

 

 

 

 

Excessive mower vibration.

1.

Blade mounting hardware is loose.

1.

Tighten to 50-60 ft.lbs (68-81 N.m.).

 

2.

Mower blades, spindles,

2.

See authorized service dealer.

 

 

or pulleys are bent.

 

 

 

3.

Mower blades are out

3.

Remove, sharpen, and balance blades.

 

4.

Belt installed incorrectly.

4.

See authorized service dealer.

 

 

 

 

 

Excessive belt wear or breakage.

1.

Bent or rough pulleys.

1.

See authorized service dealer.

 

2.

Using incorrect belt.

2.

See authorized service dealer.

Mower drive belt slips

1.

Idler pulley spring broken or not

or fails to drive.

 

properly attached.

 

2.

Mower drive belt broken.

1.See authorized service dealer.

2.See authorized service dealer.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Manual No Rev ‘A’, 6/14/2010 Not ForIdentification Numbers Service, or information you Must have these numb rsUnit ID Tag Table of Contents Read the Manual Operator SafetyOperating Safety Operator’s manual contains important safety informationThrown Objects Slope OperationMoving Parts Retaining Walls, Drop-offs, and Water Fuel and MaintenanceEnclosed Areas Preparation Protection Against Tipovers Protection for Children Protection Against TipoversSafe Handling of Gasoline Preparation OperationEmissions Towing Maintenance Decal, Caution Safety and Instructional DecalsDecal, Warning Operational Safety Checks Safety Interlock SystemControl Functions Features and ControlsGround Speed Levers Seat Adjustment Lever Ignition SwitchMower Cutting Height Adjustment Switch PTO Switch Hour MeterBefore first time operation General Operating SafetyOperation Checks Before StartingStopping the Rider and Engine Starting the EngineMowing Levers Gradually Zero Turn Smooth Travel Driving PracticeForward Travel Practice Reverse Travel Practice Forward Reverse TravelTurning In-Place Practice Turning In PlaceAllows you to turn around at the end of a cutting 20’ 6m Attaching a TrailerMaintenance Chart MaintenanceVer-filling and wipe up any Engine MaintenanceAfter installation Fuel FilterSource such as a furnace, water heater, etc. and cause an Precautions may result in serious injury or deathStorage Never store the unit with fuel in an enclosed, poorlyGround Speed Lever Adjustment Adjustments and ServiceSpeed Balancing Adjustment Seat AdjustmentsTion indicated by the arrow, and remove the mower belt Cutting Height AdjustmentMower Removal and Installation RemovalWasher and hairpin clip a InstallationTion indicated, and install the belt onto the PTO pulley as With a washer and hairpin clip aBlade Brake Check PTO Clutch AdjustmentPTO Clutch Adjustment Perform the following procedure if the clutch is slippingRight side shown, left side hidden Mower Deck LevelingDamaged, it must be replaced Remove mower deck see Mower Deck RemovalFig re 27. Balancing The Blade Oil LubricationGrease Front caster wheel axlesBattery Charging Battery MaintenanceTroubleshooting the Rider TroubleshootingTroubleshooting Warranty Period WarrantyNot For Not For Not For Maintenance Items SpecificationsDimensions Chassis Replacement Parts

285Z specifications

The Snapper 285Z is a robust and versatile zero-turn mower designed for efficient lawn care, making it an excellent choice for both homeowners and landscaping professionals. Renowned for its reliability and performance, the Snapper 285Z stands out in the competitive market of outdoor power equipment.

One of the main features of the Snapper 285Z is its powerful engine options. Equipped with a high-performance, commercial-grade engine, it delivers outstanding torque and power to tackle various mowing conditions. This ensures that users can easily mow through tough grass and uneven terrains without bogging down. The engine is designed for easy starting and smooth operation, contributing to the overall user experience.

The patented zero-turn technology of the Snapper 285Z allows for unparalleled maneuverability. With its dual-lever steering system, operators can easily turn in tight spaces and navigate around obstacles with confidence. This feature significantly reduces mowing time and enhances efficiency, making it ideal for residential lawns, commercial properties, and intricate landscaping designs.

The Snapper 285Z also boasts an adjustable cutting deck, with widths typically ranging from 48 to 52 inches, allowing users to choose the perfect size for their mowing needs. The deck is constructed from durable steel, ensuring longevity and resistance to wear and tear. Additionally, the cutting height can be quickly adjusted, offering versatility for different grass types and seasonal growth patterns.

Another notable characteristic of the Snapper 285Z is its user-friendly design. With a comfortable seat, ergonomic controls, and an easy-to-read instrument panel, it promotes a pleasant mowing experience. The mower is also equipped with an electric start feature, eliminating the need for pull cords and enhancing ease of use.

Safety is a top priority with the Snapper 285Z, featuring roll-over protection and safety switches that ensure the mower shuts down when the operator leaves the seat. This attention to safety not only protects the user but also adds to the mower's overall reliability.

In summary, the Snapper 285Z combines powerful performance, innovative technology, and user-focused features to offer an exceptional mowing experience. Its zero-turn capability, durable construction, and adjustable cutting options make it a top choice for anyone looking to maintain a beautiful lawn efficiently.
Top Page Image Contents