Snapper 285Z manual Starting the Engine, Stopping the Rider and Engine, Mowing

Page 15

Operation

Starting the Engine

Pushing the Rider by Hand

NOTE: The engine on this unit features an Electronic Fuel Management (EFM) system, and does not require choking.

1.While sitting in the operator’s seat, make sure the PTO switch is disengaged, the parking brake is engaged, and the ground speed levers are locked in the START/PARK position.

2.Set the engine speed control to the FAST position.

3.Insert the key into the ignition switch and turn it to START.

4.After the engine starts, warm up the engine by running it for at least a minute before engaging the PTO switch or driving the rider.

5.After warming the engine, ALWAYS operate the rider at FULL ENGINE SPEED when mowing.

1.Disengage the PTO, engage the parking brake, lock the ground speed levers into their START/PARK positions, turn the ignition OFF, remove the key, and wait for all moving parts to stop.

2.To disengage the transmissions, pull the roll release rods (A, Figure 2), located on either side of the engine, up into the PUSH position.

3.Disengage the parking brake.

The rider can now be pushed by hand.

4.After moving the rider, re-engage the transmissions by pushing the roll release rods back down to the DRIVE position.

In the event of an emergency the engine can be stopped by

 

 

 

 

 

simply turning the ignition switch to STOP. Use this method

 

 

 

 

 

 

Reproduction

 

only in emergency situations. For normal engine shut down

 

DO NOT TOW RIDER

 

 

Towing the u

it will cause transmission

follow the procedure given in STOPPING THE RIDER.

 

damage. Do

ot use another vehicle to push

Stopping the Rider and Engine

 

 

 

or pull this u

it.

 

1.

Return the ground speed levers to the middle (or neutral

 

 

 

 

 

‘N’) position to stop rider movement. Pivot the levers out-

 

 

 

 

 

ward to lock them in the START/PARK p

siti n.

 

 

 

 

 

2.

Engage the parking brake by moving the parking brake

 

 

 

 

A

 

lever forward and to the right.

 

 

 

 

 

 

 

3.

Disengage the PTO by pushing down on the PTO switch.

 

 

 

 

4.

Turn the ignition key to OFF. Remove the key.

 

 

 

 

 

NOTE: The engine on this unit is equipped with a fuel s len

id

 

 

 

 

to minimize after fire. Though it should make no diffe ence

 

 

 

 

 

whether it is shut down with the engine sp

control set to

 

 

 

 

 

FAST or SLOW, FAST is recommended.

 

 

 

 

 

 

 

 

Figure 2. Roll Release Components (On Each Side)

Mowing

 

 

 

 

 

 

 

 

 

 

1.

Make sure the PTO switch is disengaged, the parking brake

 

 

 

 

 

is engaged, the ground speed levers are locked in their

 

WARNING

 

 

 

START/PARK positions, and the operator is in the seat.

 

 

 

 

 

 

 

DO NOT disengage the transmissions and coast down

2.

Start the engine (see STARTING THE ENGINE).

 

3.

Set the mower cutting height (see CUTTING HEIGHT

 

slopes. DO NOT use Roll Release to disengage the

 

transmissions unless machine motion can be controlled

 

ADJUSTMENT).

 

 

 

 

 

 

 

and engine is off.

 

 

 

 

 

 

 

 

 

 

 

4.Set the engine speed control to FAST.

5.Engage the PTO by pulling up on the switch.

6.Pivot the ground speed levers in from the START/PARK position to the neutral ‘N’ position.

7.Begin mowing. See Operator Safety for tips on safe mowing practices.

8.When finished, shut off the PTO.

9.Stop the engine (see STOPPING THE RIDER AND ENGINE).

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Manual No Rev ‘A’, 6/14/2010 Not ForService, or information you Must have these numb rs Identification NumbersUnit ID Tag Table of Contents Read the Manual Operator SafetyOperating Safety Operator’s manual contains important safety informationSlope Operation Thrown ObjectsMoving Parts Fuel and Maintenance Retaining Walls, Drop-offs, and WaterEnclosed Areas Preparation Protection Against Tipovers Protection for Children Protection Against TipoversPreparation Operation Safe Handling of GasolineEmissions Towing Maintenance Safety and Instructional Decals Decal, CautionDecal, Warning Operational Safety Checks Safety Interlock SystemFeatures and Controls Control FunctionsGround Speed Levers Seat Adjustment Lever Ignition SwitchMower Cutting Height Adjustment Switch PTO Switch Hour MeterBefore first time operation General Operating SafetyOperation Checks Before StartingStarting the Engine Stopping the Rider and EngineMowing Levers Gradually Zero Turn Smooth Travel Driving PracticeForward Travel Practice Reverse Travel Practice Forward Reverse TravelPractice Turning In Place Turning In-PlaceAllows you to turn around at the end of a cutting 20’ 6m Attaching a TrailerMaintenance Chart MaintenanceVer-filling and wipe up any Engine MaintenanceAfter installation Fuel FilterSource such as a furnace, water heater, etc. and cause an Precautions may result in serious injury or deathStorage Never store the unit with fuel in an enclosed, poorlyGround Speed Lever Adjustment Adjustments and ServiceSpeed Balancing Adjustment Seat AdjustmentsTion indicated by the arrow, and remove the mower belt Cutting Height AdjustmentMower Removal and Installation RemovalWasher and hairpin clip a InstallationTion indicated, and install the belt onto the PTO pulley as With a washer and hairpin clip aBlade Brake Check PTO Clutch AdjustmentPTO Clutch Adjustment Perform the following procedure if the clutch is slippingRight side shown, left side hidden Mower Deck LevelingRemove mower deck see Mower Deck Removal Damaged, it must be replacedFig re 27. Balancing The Blade Oil LubricationGrease Front caster wheel axlesBattery Charging Battery MaintenanceTroubleshooting the Rider TroubleshootingTroubleshooting Warranty Period WarrantyNot For Not For Not For Maintenance Items SpecificationsDimensions Chassis Replacement Parts

285Z specifications

The Snapper 285Z is a robust and versatile zero-turn mower designed for efficient lawn care, making it an excellent choice for both homeowners and landscaping professionals. Renowned for its reliability and performance, the Snapper 285Z stands out in the competitive market of outdoor power equipment.

One of the main features of the Snapper 285Z is its powerful engine options. Equipped with a high-performance, commercial-grade engine, it delivers outstanding torque and power to tackle various mowing conditions. This ensures that users can easily mow through tough grass and uneven terrains without bogging down. The engine is designed for easy starting and smooth operation, contributing to the overall user experience.

The patented zero-turn technology of the Snapper 285Z allows for unparalleled maneuverability. With its dual-lever steering system, operators can easily turn in tight spaces and navigate around obstacles with confidence. This feature significantly reduces mowing time and enhances efficiency, making it ideal for residential lawns, commercial properties, and intricate landscaping designs.

The Snapper 285Z also boasts an adjustable cutting deck, with widths typically ranging from 48 to 52 inches, allowing users to choose the perfect size for their mowing needs. The deck is constructed from durable steel, ensuring longevity and resistance to wear and tear. Additionally, the cutting height can be quickly adjusted, offering versatility for different grass types and seasonal growth patterns.

Another notable characteristic of the Snapper 285Z is its user-friendly design. With a comfortable seat, ergonomic controls, and an easy-to-read instrument panel, it promotes a pleasant mowing experience. The mower is also equipped with an electric start feature, eliminating the need for pull cords and enhancing ease of use.

Safety is a top priority with the Snapper 285Z, featuring roll-over protection and safety switches that ensure the mower shuts down when the operator leaves the seat. This attention to safety not only protects the user but also adds to the mower's overall reliability.

In summary, the Snapper 285Z combines powerful performance, innovative technology, and user-focused features to offer an exceptional mowing experience. Its zero-turn capability, durable construction, and adjustable cutting options make it a top choice for anyone looking to maintain a beautiful lawn efficiently.
Top Page Image Contents