Snapper ZT19441KWV, ZT20501BV Operation, Starting the Engine, Stopping the Rider, Mowing

Page 10

WARNING

If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES & CONTROLS section, do so now. Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls.

STARTING THE ENGINE

1.While sitting in the operator’s seat, engage the park- ing brake and make sure the PTO switch is disen- gaged and the motion control handles are locked in the NEUTRAL position.

2.NOTE: A warm engine may not require choking. Set the engine throttle control to FAST throttle posi- tion. Then fully close the choke by pulling the knob OUT fully.

3.Insert the key into the ignition switch and turn it to

START.

4.After the engine starts, gradually open the choke (push knob down fully).

Warm up the engine by running it for at least a minute before engaging the PTO switch or driving the rider.

5.After warming the engine, ALWAYS operate the unit at FULL THROTTLE when mowing.

In the event of an emergency the engine can be stopped by simply turning the ignition switch to STOP. Use this method only in emergency situations. For normal engine shut down follow the procedure given in STOPPING THE RIDER.

STOPPING THE RIDER

1.Returning the ground speed control levers to the mid- dle position will stop tractor movement. Pivot the levers outward and lock them in NEUTRAL.

2.Disengage the PTO by pushing down on the PTO switch.

3.Engage the parking brake by pulling the handle up until it locks into position.

4.Move the throttle control to mid-throttle position and turn the ignition key to OFF. Remove the key.

Operation

MOWING

1.Engage the parking brake. Make sure the PTO switch is disengaged, the motion control handles are locked in the NEUTRAL position and the operator is on the seat.

2.Start the engine (see STARTING THE ENGINE).

3.Set the mower cutting height.

4.Set the throttle to FULL.

5.Engage the PTO by pulling up on the PTO switch.

6.Begin mowing. See Section LC for tips on mowing patterns, lawn care, and trouble shooting information.

7.When finished, shut off the PTO.

8.Stop the engine (see STOPPING THE TRACTOR AND ENGINE).

PUSHING THE RIDER BY HAND

DO NOT TOW RIDER

Towing the unit will cause hydraulic pump and wheel motor damage. Do not use another vehicle to push or pull this unit.

1.Disengage the PTO, engage the parking brake, turn the ignition OFF, and remove the key.

2.Lift the seat plate to gain access to the hydraulic pumps.

3.To disengage the pumps (free-wheel position), turn the hydraulic release valves (A, Figure 2) located on the pumps COUNTER-CLOCKWISE a maximum of 2 full turns.

4.Disengage the parking brake.

The tractor can now be pushed by hand.

5.After moving the tractor, re-engage the pumps (drive position) by turning the release valves CLOCKWISE and tighten to 80-120 in. lbs. of torque.

A

Figure 2. Transmission Release Valves

A. Hydraulic Release Valve (On Each Pump)

9

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model Number Explanation ModelZT18441KHC ZT19441KWV ZT20501BV McDonough, GA 30253 USATable of Contents General Operation Safety Rules and InformationTransporting and Storage Children Slope OperationTowed Equipment RIDE-ON Units EmissionsService & Maintenance Service and MaintenanceSafe Handling of Gasoline Safety Decals Safety DecalsDecal Cut Height Decal CZT Hydro Release Decal Belt & Blade Ground Speed Levers Throttle Control Control FunctionsChoke Features & Controls General Operating Safety Checks Before StartingStopping the Rider OperationStarting the Engine MowingForward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerExecuting Turns Trailer Weight Recommendations Clevis Pin Clip Attaching a TrailerInstallation Mower Removal InstallationRemoval Engine Maintenance Items Safety ItemsRider Maintenance Items Before Every Spring Each Hours 100 250 Fall UseGrease Regular MaintenanceLubrication OilService Interval Every 10 Hours or As Required Servicing the Mower BladesChecking / Adding Fuel Engine Maintenance Check /FILL Transmission OILCheck Tire Pressures Fuel FilterTransmission OIL Filter Change Battery MaintenanceCleaning the Battery and Cables StorageTroubleshooting, Adjustments, & Service Troubleshooting the RiderTroubleshooting, Adjustments, & Service Troubleshooting the MowerSpeed Balancing Adjustment Seat AdjustmentGround Speed Control Lever Adjustment Seat Position AdjustmentNeutral Adjustment Cutting Height AdjustmentParking Brake Adjustment Brake AdjustmentPTO Clutch Adjustment Blade Brake CheckMower Deck Leveling Orient Blades Side-to-SideHydraulic Pump Drive Belt Replacement Battery ChargingMower Belt Replacement PRY Belts Over PulleysPage Page Safety Instructions & Operator’s Manual for

ZT18441KHC, ZT19441KWV, ZT20501BV specifications

The Snapper ZT20501BV, ZT19441KWV, and ZT18441KHC are innovative zero-turn lawn mowers designed to deliver exceptional performance, efficiency, and maneuverability. Each model features a robust engine and advanced technology, making them ideal for both residential and commercial lawn care.

Starting with the Snapper ZT20501BV, this model is powered by a dependable Briggs & Stratton engine that delivers reliable performance and ease of maintenance. With a cutting deck width of 50 inches, it provides an efficient cutting experience, enabling users to cover large areas swiftly. The ZT20501BV also boasts a dual hydrostatic transmission that enhances maneuverability and speed, allowing for precise control. Additionally, the mower is equipped with a high-back seat with armrests for optimal comfort during prolonged use, ensuring that operators can tackle demanding lawn maintenance tasks without strain.

Next, the Snapper ZT19441KWV is designed with a 42-inch cutting deck, making it great for residential lawns with obstacles. This model is powered by a powerful Kohler engine, renowned for its durability and performance. The ZT19441KWV features a foot-operated deck lift, which allows users to easily adjust the cutting height on the go, enhancing convenience. Its compact design enables easy navigation around flower beds and shrubs, while its responsive zero-turn capability ensures that users can maneuver around tight corners with ease.

Finally, the Snapper ZT18441KHC offers a 42-inch cutting deck and is powered by a reliable Kawasaki engine. The ZT18441KHC stands out with its innovative air-cooled design, providing consistent performance even under heavy workloads. This model includes a user-friendly dashboard control panel that gives operators quick access to operational information, enhancing the mowing experience. The ZT18441KHC also features innovative safety measures, such as an operator presence system that ensures the engine shuts off when the operator leaves the seat, promoting safety during operation.

All three models are constructed with durable materials, ensuring longevity and reliability. Each mower is designed for ease of use, with features that enhance comfort, safety, and efficiency. With their advanced technologies and robust characteristics, the Snapper ZT20501BV, ZT19441KWV, and ZT18441KHC are optimal choices for anyone seeking a high-performance zero-turn mower to maintain their lawn effectively and effortlessly.
Top Page Image Contents