Snapper ZT18441KHC, ZT20501BV, ZT19441KWV important safety instructions Features & Controls

Page 8

Ignition Switch

The ignition switch starts and stops the engine; it has three positions:

OFF

Stops the engine and shuts off the

 

electrical system.

RUN

Allows the engine to run and powers the

 

electrical system.

START

Cranks the engine for starting.

NOTE: Never leave the ignition switch in the RUN posi- tion with the engine stopped–this drains the battery.

Hour Meter / Maintenance Reminder

The hour meter measures the number of hours the key has been in the RUN position. The hour meter will flash an initial oil change indicator at 5 hours, and a lubrication reminder every 50 hours. These reminders display for approximately two hours and will automatically reset themselves.

Note: The hour meter will register the passage of time when the key is in the RUN position, even if the engine is not running. The hour meter has a self contained power source so the total hours are always visible.

PTO Switch

The PTO (Power Take-Off) switch engages and disen- gages attachments that use the PTO. To engage the PTO, pull UP on the switch. Push DOWN to disengage. Note that the operator must be seated firmly in the rider seat for the PTO to function.

Transmission Oil Fill

Transmission oil is added through the transmission oil expansion chamber. It also serves as extra holding capacity for oil as the transmission heats up and the oil expands. See CHECK TRANSMISSION OIL LEVEL for oil level check and fill procedures.

Transmission Release Valves

The transmission release valves deactivate the transmis- sions so that the unit can be pushed by hand. See PUSHING THE UNIT BY HAND for operational informa- tion.

Seat Adjustment Lever

The seat can be adjusted forward and backward. Move the adjustment lever towards the left, slide the seat to the desired position, and release the lever.

Features & Controls

Fuel Tank & Gauge

To remove the cap, turn counterclockwise. The fuel gauge is mounted in the fuel tank and indicates the amount of fuel in the tank.

Mower Height of Cut Adjustment &

Attachment Lift Control Lever

To adjust cutting height, pull the large lever back fully to lock the control in the attachment raised transport posi- tion. Position the cutting height selector pin on the appropriate hole to achieve the desired cutting height. Pull back on the small lift latch lever and large lever simultaneously, and lower the mower into cutting posi- tion.

For attachment transport lift, pull the large lift lever back fully to lock the control in the attachment raised transport position.

Parking Brake

DISENGAGE

Releases the parking brake.

ENGAGE

Locks the parking brake.

Pull the parking brake lever back to engage the parking brake. Move the lever fully forward to disengage the parking brake. NOTE: To start the unit the parking brake must be engaged.

7

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model ZT18441KHC ZT19441KWV ZT20501BVModel Number Explanation McDonough, GA 30253 USATable of Contents Transporting and Storage Safety Rules and InformationGeneral Operation Slope Operation Towed Equipment RIDE-ON UnitsChildren EmissionsSafe Handling of Gasoline Service and MaintenanceService & Maintenance Decal Cut Height Decal CZT Hydro Release Decal Belt & Blade Safety DecalsSafety Decals Choke Control FunctionsGround Speed Levers Throttle Control Features & Controls General Operating Safety Checks Before StartingOperation Starting the EngineStopping the Rider MowingZero Turn Driving Practice Smooth TravelForward Travel Practice Reverse Travel PracticeExecuting Turns Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Trailer Weight Recommendations Clevis Pin Clip Attaching a TrailerRemoval Mower Removal InstallationInstallation Safety Items Rider Maintenance ItemsEngine Maintenance Items Before Every Spring Each Hours 100 250 Fall UseRegular Maintenance LubricationGrease OilService Interval Every 10 Hours or As Required Servicing the Mower BladesEngine Maintenance Check /FILL Transmission OIL Check Tire PressuresChecking / Adding Fuel Fuel FilterBattery Maintenance Cleaning the Battery and CablesTransmission OIL Filter Change StorageTroubleshooting, Adjustments, & Service Troubleshooting the RiderTroubleshooting, Adjustments, & Service Troubleshooting the MowerSeat Adjustment Ground Speed Control Lever AdjustmentSpeed Balancing Adjustment Seat Position AdjustmentCutting Height Adjustment Parking Brake AdjustmentNeutral Adjustment Brake AdjustmentPTO Clutch Adjustment Blade Brake CheckMower Deck Leveling Orient Blades Side-to-SideHydraulic Pump Drive Belt Replacement Battery ChargingMower Belt Replacement PRY Belts Over PulleysPage Page Safety Instructions & Operator’s Manual for

ZT18441KHC, ZT19441KWV, ZT20501BV specifications

The Snapper ZT20501BV, ZT19441KWV, and ZT18441KHC are innovative zero-turn lawn mowers designed to deliver exceptional performance, efficiency, and maneuverability. Each model features a robust engine and advanced technology, making them ideal for both residential and commercial lawn care.

Starting with the Snapper ZT20501BV, this model is powered by a dependable Briggs & Stratton engine that delivers reliable performance and ease of maintenance. With a cutting deck width of 50 inches, it provides an efficient cutting experience, enabling users to cover large areas swiftly. The ZT20501BV also boasts a dual hydrostatic transmission that enhances maneuverability and speed, allowing for precise control. Additionally, the mower is equipped with a high-back seat with armrests for optimal comfort during prolonged use, ensuring that operators can tackle demanding lawn maintenance tasks without strain.

Next, the Snapper ZT19441KWV is designed with a 42-inch cutting deck, making it great for residential lawns with obstacles. This model is powered by a powerful Kohler engine, renowned for its durability and performance. The ZT19441KWV features a foot-operated deck lift, which allows users to easily adjust the cutting height on the go, enhancing convenience. Its compact design enables easy navigation around flower beds and shrubs, while its responsive zero-turn capability ensures that users can maneuver around tight corners with ease.

Finally, the Snapper ZT18441KHC offers a 42-inch cutting deck and is powered by a reliable Kawasaki engine. The ZT18441KHC stands out with its innovative air-cooled design, providing consistent performance even under heavy workloads. This model includes a user-friendly dashboard control panel that gives operators quick access to operational information, enhancing the mowing experience. The ZT18441KHC also features innovative safety measures, such as an operator presence system that ensures the engine shuts off when the operator leaves the seat, promoting safety during operation.

All three models are constructed with durable materials, ensuring longevity and reliability. Each mower is designed for ease of use, with features that enhance comfort, safety, and efficiency. With their advanced technologies and robust characteristics, the Snapper ZT20501BV, ZT19441KWV, and ZT18441KHC are optimal choices for anyone seeking a high-performance zero-turn mower to maintain their lawn effectively and effortlessly.
Top Page Image Contents