Troubleshooting, Adjustments, & Service
Rider Troubleshooting Continued.
PROBLEM | CAUSE | REMEDY | |
Engine runs, but rider will | 1. | Hydraulic release valve(s) | 1. Turn valve(s) clockwise to close. |
not drive. |
| in “open” position. |
|
| 2. | Belt is broken. | 2. See Drive Belt Replacement. |
| 3. | Drive belt slips. | 3. See problem and cause below. |
| 4. | Brake is not fully released. | 4. See authorized service dealer |
|
|
|
|
Rider drive belt slips. | 1. | Pulleys or belt greasy or oily. | 1. Clean as required. |
| 2. | Belt stretched or worn. | 2. Replace belt. |
|
|
|
|
Brake will not hold. | 1. | Brake is incorrectly adjusted. | 1. See Brake Adjustment. |
| 2. | Brake caliper pads worn. | 2. See your dealer. |
|
|
|
|
Rider steers or handles poorly. | 1. | Steering linkage is loose. | 1. Check and tighten any loose connections. |
| 2. | Improper tire inflation. | 2. See Regular Maintenance Section. |
|
|
|
|
TROUBLESHOOTING THE MOWER
PROBLEM | CAUSE | REMEDY | |
Mower will not raise. | 1. | Lift linkage not properly attached | 1. See authorized service dealer for repair. |
|
| or damaged. |
|
|
|
|
|
Mower cut is uneven. | 1. | Mower not leveled properly. | 1. See Mower Adjustment. |
| 2. | Rider tires not inflated | 2. See Regular Maintenance Section. |
|
| equally or properly. |
|
Mower cut is rough looking.
1. | Engine speed too slow. | 1. Set throttle to full. |
2. | Ground speed too fast. | 2. Decrease Ground Speed. |
3. | Blades are dull. | 3. Sharpen or replace blades. |
|
| See Mower Blade Service. |
4. | Mower drive belt slipping | 4. Clean or replace belt as necessary. |
| because it is oily or worn. |
|
5. | Blades not properly fastened | 5. See Servicing the Mower Blades. |
| to arbors. |
|
Engine stalls easily with | 1. | Engine speed too slow. | 1. Set to full throttle. |
mower engaged. | 2. | Ground speed too fast. | 2. Decrease Ground Speed. |
| 3. | Cutting height set too low. | 3. Cut tall grass at maximum cutting |
|
|
| height during first pass. |
| 4. | Discharge chute jamming | 4. Cut grass with discharge pointing toward |
|
| with cut grass. | previously cut area. |
|
|
|
|
Excessive mower vibration. | 1. | Blade mounting bolts are loose. | 1. Tighten to |
| 2. | Mower blades, arbors, | 2. Check and replace as necessary. |
|
| or pulleys are bent. |
|
| 3. | Mower blades are out | 3. Remove, sharpen, and balance blades. |
|
| of balance. | See Maintenance Section. |
| 4. | Belt installed incorrectly. | 4. Reinstall Correctly. |
|
|
|
|
Excessive belt wear or breakage. | 1. | Bent or rough pulleys. | 1. Repair or replace. |
| 2. | Using incorrect belt. | 2. Replace with correct belt. |
|
|
|
|
Mower drive belt slips | 1. | Idler pulley spring broken or not | 1. Repair or replace as needed. |
or fails to drive. |
| properly attached. |
|
| 2. | Mower drive belt broken. | 2. Replace drive belt. |
20