Snapper NZM19482KWV, NZM21522KWV, NZM25612KWV, NZM27612KH Starting Engine

Page 10

Section 3 - OPERATING INSTRUCTIONS

ROLL RELEASE: To roll the machine without the engine running, pressure within the hydraulic pumps must be released. There is a hydraulic pressure relief valve on the upper side of each pump that is used to release the pressure. Use a wrench to rotate both relief valves counter clockwise two full turns to open. After rolling machine, both relief valves must be rotated clockwise to close valves and tighten securely before operating machine. Machine will not move if relief valves are open. See Figure 3.4.

ROTATE RELIEF VALVE

COUNTERCLOCKWISE

TO RELIEVE PRESSURE

RELIEF VALVE

3.2 STARTING & STOPPING – ENGINE, BLADES, PARKING BRAKE

This machine is equipped with dual hydrostatic wheel drive transmissions. Each hydro pump is controlled by a separate motion control lever. The left lever controls the left wheel drive hydro pump and the right lever controls the right wheel drive hydro pump. These levers control the direction of motion, Forward & Reverse, and the speed of motion. Move both levers forward to propel the machine forward. Move both levers rearward to propel the machine in reverse. The speed of motion is continuously variable from neutral (zero) to the maximum. Moving the levers farther from the neutral position will cause the speed of motion to increase. To turn, move the lever on the side to which you want to turn slightly rearward of the other lever. Move levers slowly and carefully. DO NOT make sudden changes in speed or direction. Always slow machine motion before turning. To stop the motion of the machine, bring both motion control levers to the neutral position. Engage parking brake.

3.2.1. STARTING ENGINE

When the ignition key is turned the engine will not start or turn over unless, the blade switch is pushed in to the “OFF” position and the motion control levers are in the neutral lock position. Always engage parking brake before starting engine.

1.Complete pre-start checklist.

2.Sit in operator’s seat.

3.Push blade switch in to “OFF”, blades disengaged position and engage parking brake. See Figure 3.2.

4.Move choke control forward to choke position to start a cold engine. See Figure 3.5.

5.Move engine speed control to the Rabbit “FAST” position. See Figure 3.5.

6.Turn key to the start position until engine starts. See Figure 3.6.

CHOKE

ENGINE

KEY

SPEED

CONTROL

CONTROL

SWITCH

FIGURE 3.4

WARNING

DO NOT disengage the hydro transmission and coast down slopes. DO NOT use Roll Release Control to disengage the hydro transmission unless machine motion can be controlled and engine is off.

MOTION CONTROL LEVERS SHOWN IN THE NEUTRAL

LOCK POSITION

SHOWN FROM OPERATOR’S VIEW POINT

FIGURE 3.5

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions From Previous SnapperMaintenance Table of Contents Your Snapper dealer if you have questions Are provided for reference only and mayDiffer from your specific model. Contact IntroductionSafety Messages and Symbols RUN Operating Instructions PRE-START Check ListStarting & Stopping ENGINE, BLADES, Parking Brake Starting EngineStopping Mower Blades Stopping EngineStarting Mower Blades Parking BrakeCutting Height Adjustment OPERATION- Motion Controls Driving MachineEngine should Start if Stopping MachineEngine Must not Start if Engine Must Begin to Stop ifService After First 5 Hours Check Mower BladeAfter Every 25 Operating Hours 4.3.1. Engine Before Operating Machine Riding Mower LubricationAnnually END of Each Season Deck Removal See Figure Adjustments & Repair Neutral Position AdjustmentsMower Deck Adjustment Levelness Neutral Position Adjustments From PreviousMower Deck & Component Adjustments Side to Side and Front to RearParking Brake Adjustment Highest cutting position and recheck side to sideTraction Belt Replacement Traction Belt TensionBelt Replacement Tracking AdjustmentMower Drive Belt Replacement Belt RemovalBlade Sharpening Battery Installation Battery Battery RemovalBattery Charging NEW Battery Preparation 1.Remove battery from carton Battery TestingState of Charge Digital Voltmeter Bearing Replacement Insert spindle shaft up through the bottomHydraulic SYSTEM, Purging Trouble Shooting on Next Problem Probable CauseCorrective Action Machine Will Not Move 100 Service Performed EachMAINTENANCE/REPLACEMENT Parts Number USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series

NZM25612KWV, NZM19482KWV, NZM21522KWV, NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV, NZM27612KH, NZM21522KWV, NZM19482KWV, NZM25612KWV, NZM27612KH, NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV specifications

The Snapper series of zero-turn mowers, including models NZM25612KWV, NZM19482KWV, NZM21522KWV, and NZM27612KH, are designed to deliver optimal performance, exceptional comfort, and cutting-edge technology for residential and commercial lawn care. Each model presents unique characteristics tailored to different mowing needs, making them suitable for various landscaping tasks.

The NZM25612KWV stands out with its powerful 25 horsepower engine, coupled with a robust 52-inch cutting deck. The cutting height adjustment feature allows for precision mowing, enabling users to achieve their desired grass length effortlessly. This model is particularly appreciated for its impressive maneuverability, making it ideal for navigating around obstacles in large yards or commercial properties.

On the other hand, the NZM19482KWV offers a slightly smaller footprint with a 48-inch cutting deck powered by a 19 horsepower engine. This model is perfect for homeowners with smaller lawns while still providing the efficiency and speed of a zero-turn mower. The compact design allows for easy storage, while the comfortable seating and intuitive controls contribute to a seamless mowing experience.

The NZM21522KWV combines the best of both worlds, featuring a 22 horsepower engine and a 54-inch cutting deck. This model is designed for those who require a balance between power and cutting width, making it versatile for both residential and commercial use. Additionally, its advanced vibration-dampening technology ensures comfort, even during extended mowing sessions.

Then there's the NZM27612KH, which boasts an impressive 27 horsepower engine paired with a 60-inch cutting deck. This powerhouse model is specifically engineered for large properties and professional landscapers who demand reliability and efficiency. With an expanded fuel tank and heavy-duty construction, it tackles extensive mowing tasks with ease, providing a crisp and clean cut every time.

In terms of technology, all the Snapper models incorporate user-friendly features such as electric deck lift options, easy-to-read LED displays for monitoring speed and battery life, and enhanced safety mechanisms. These models are also built with high-quality materials, ensuring durability and longevity in performance. Special attention is given to ease of maintenance, with accessible components for quick servicing and repairs.

Overall, Snapper mowers like the NZM25612KWV, NZM19482KWV, NZM21522KWV, and NZM27612KH not only elevate the gardening experience through their innovative design and advanced engineering but also enhance productivity for both at-home lawn care enthusiasts and professional landscapers alike.
Top Page Image Contents