Snapper NZM21522KWV, NZM19482KWV, NZM25612KWV, NZM27612KH Deck Removal

Page 17

Section 4 - MAINTENANCE

WARNING

Allow engine to cool for at least ten minutes before performing service or maintenance. DO NOT smoke near fuel components when performing service or maintenance. DO NOT perform service and maintenance near an open flame. Wipe off any spilled fuel before starting engine. DO NOT run engine indoors.

4.5ANNUALLY (END OF EACH SEASON) (Continued from previous Page) 4.5.2. FUEL FILTER

Service fuel filter as instructed below. Turn key to “OFF” position. Engine MUST be stopped and MUST be cold before removing filter. Clamp fuel line to prevent fuel spillage or perform filter change when fuel tank and fuel line are empty.

1.Remove fuel line clamps from fuel filter.

2.Remove fuel lines from filter. Discard filter.

3.Install new fuel filter. IMPORTANT: Some fuel filters are fuel flow directional. Check for arrow that shows fuel flow direction. Reinstall fuel line clamps. See Figure 4.8.

LEFT SIDE OF

MACHINE

4.6DECK REMOVAL

Move power unit/mower deck to an area where the mower deck is to be disconnected. Turn engine “OFF” and remove key from switch. Remove spark plug wire(s) and secure away from spark plug(s). Move motion control levers to the neutral position. Engage parking brake.

1.Move deck lift lever and set the mower deck to the highest cutting position. See Figure 4.9.

2.IMPORTANT – STORED ENERGY. Relieve tension on deck lift assist spring by backing off nut on eyebolt. Failure to relive tension could result in personal injury. See Figure 4.9.

3.Place a wooden block under the front and rear edge of the mower deck.

4.Move deck lift lever and set the mower deck to a lower cutting position until deck rests on wooden blocks. Position the deck to where there is no tension on the deck hanger chains. See Figure 4.9.

LOWEST CUTTING

POSITION (ALL THE

WAY FORWARD)

POSITION DECK LIFT LEVER IN HIGHEST CUTTING POSITION. PLACE WOODEN BLOCKS UNDER FRONT AND REAR OF DECK. LOWER DECK ONTO BLOCKS

LOOSEN DECK

CLAMP FUEL LINELIFT ASSIST TO PREVENT

SPILLAGE

REMOVE

FUEL FILTER

 

CLAMP FUEL

REMOVE LINE

LINE TO

PREVENT

CLAMPS

SPILLAGE

 

FIGURE 4.8

FIGURE 4.9

(Continued On Next Page)

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions Snapper From PreviousMaintenance Table of Contents Differ from your specific model. Contact Are provided for reference only and mayYour Snapper dealer if you have questions IntroductionSafety Messages and Symbols RUN PRE-START Check List Operating InstructionsStarting Engine Starting & Stopping ENGINE, BLADES, Parking BrakeStarting Mower Blades Stopping EngineStopping Mower Blades Parking BrakeOPERATION- Motion Controls Driving Machine Cutting Height AdjustmentEngine Must not Start if Stopping MachineEngine should Start if Engine Must Begin to Stop ifCheck Mower Blade Service After First 5 HoursAfter Every 25 Operating Hours 4.3.1. Engine Annually END of Each Season Riding Mower LubricationBefore Operating Machine Deck Removal See Figure Neutral Position Adjustments Adjustments & RepairMower Deck & Component Adjustments Neutral Position Adjustments From PreviousMower Deck Adjustment Levelness Side to Side and Front to RearHighest cutting position and recheck side to side Parking Brake AdjustmentTraction Belt Tension Traction Belt ReplacementMower Drive Belt Replacement Tracking AdjustmentBelt Replacement Belt RemovalBlade Sharpening Battery Charging Battery Battery RemovalBattery Installation State of Charge Digital Voltmeter Battery TestingNEW Battery Preparation 1.Remove battery from carton Insert spindle shaft up through the bottom Bearing ReplacementHydraulic SYSTEM, Purging Corrective Action Problem Probable CauseTrouble Shooting on Next Machine Will Not Move MAINTENANCE/REPLACEMENT Parts Service Performed Each100 Number USE HRS SeasonDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series

NZM25612KWV, NZM19482KWV, NZM21522KWV, NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV, NZM27612KH, NZM21522KWV, NZM19482KWV, NZM25612KWV, NZM27612KH, NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV specifications

The Snapper series of zero-turn mowers, including models NZM25612KWV, NZM19482KWV, NZM21522KWV, and NZM27612KH, are designed to deliver optimal performance, exceptional comfort, and cutting-edge technology for residential and commercial lawn care. Each model presents unique characteristics tailored to different mowing needs, making them suitable for various landscaping tasks.

The NZM25612KWV stands out with its powerful 25 horsepower engine, coupled with a robust 52-inch cutting deck. The cutting height adjustment feature allows for precision mowing, enabling users to achieve their desired grass length effortlessly. This model is particularly appreciated for its impressive maneuverability, making it ideal for navigating around obstacles in large yards or commercial properties.

On the other hand, the NZM19482KWV offers a slightly smaller footprint with a 48-inch cutting deck powered by a 19 horsepower engine. This model is perfect for homeowners with smaller lawns while still providing the efficiency and speed of a zero-turn mower. The compact design allows for easy storage, while the comfortable seating and intuitive controls contribute to a seamless mowing experience.

The NZM21522KWV combines the best of both worlds, featuring a 22 horsepower engine and a 54-inch cutting deck. This model is designed for those who require a balance between power and cutting width, making it versatile for both residential and commercial use. Additionally, its advanced vibration-dampening technology ensures comfort, even during extended mowing sessions.

Then there's the NZM27612KH, which boasts an impressive 27 horsepower engine paired with a 60-inch cutting deck. This powerhouse model is specifically engineered for large properties and professional landscapers who demand reliability and efficiency. With an expanded fuel tank and heavy-duty construction, it tackles extensive mowing tasks with ease, providing a crisp and clean cut every time.

In terms of technology, all the Snapper models incorporate user-friendly features such as electric deck lift options, easy-to-read LED displays for monitoring speed and battery life, and enhanced safety mechanisms. These models are also built with high-quality materials, ensuring durability and longevity in performance. Special attention is given to ease of maintenance, with accessible components for quick servicing and repairs.

Overall, Snapper mowers like the NZM25612KWV, NZM19482KWV, NZM21522KWV, and NZM27612KH not only elevate the gardening experience through their innovative design and advanced engineering but also enhance productivity for both at-home lawn care enthusiasts and professional landscapers alike.
Top Page Image Contents