Snapper NZM21522KWV, NZM19482KWV, NZM25612KWV, NZM27612KH Operating Instructions

Page 9

Section 3 - OPERATING INSTRUCTIONS

3.1PRE-START CHECK LIST

Make the following checks and perform the service required before each start-up.

3.1.1.Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be 25 psi.

3.1.2.Check guards, deflectors and covers to make sure all are in place and securely tightened.

3.1.3.Check engine oil and add oil as needed to bring level up to the FULL mark. Refer to engine owner’s manual for oil specifications. See Figure 3.1.

SAFE LEVEL

AREA

FIGURE 3.1

3.1.4.Check Blade Switch to insure it works freely.

1.Pull the Blade Switch up to the “ON” position to engage or turn “ON” the mower blades.

2.Push Blade Switch down to the “OFF” position to disengage (or turn “OFF”) the blades.

BLADE SWITCH

FIGURE 3.2

3.1.5.Clean exterior surfaces of cutting deck, engine and pumps of any accumulation of dirt, grass, oil, etc. Keep engine and pump air intake screens and cooling fins clear at all times.

3.1.6.Add fuel to both tanks of the machine outside where fumes can safely dissipate. Make sure both fuel filler caps are tight. Note the fuel tank selector valve. Refer to engine owner’s manual for fuel specifications.

3.1.7.Adjust position of operator’s seat. The seat is mounted on slides. Locate latch lever beneath the seat. Move lever towards the left and slide seat to the desired position. Release latch. If equipped, adjust seat suspension for operator weight.

3.1.8.Place mower in desired cutting height setting. Grasp deck lift lever and depress release latch located underneath the lever. Move lever to desired cutting height setting and release latch. Insert stop pin to desired cutting height.

IMPORTANT: There is a foot assist pedal located to the right front side of the footrest. Always use this assist pedal to raise or lower the deck to the desired cutting height. See Figure 3.3.

DECK LIFT

LEVER

RELEASE

LATCH

FOOT

ASSIST PEDAL

INSERT STOP PIN

INTO HOLES FOR

DESIRED CUTTING

HEIGHT

FIGURE 3.3

IMPORTANT: This machine is equipped with hydrostatic drive. The direction of motion and the speed of motion are controlled by the left and right motion control levers. A small movement of these controls can cause the machine to move instantly. DO NOT attempt to operate the machine until you read this manual and become familiar with its operation. Practice with the blades “OFF” disengaged, engine speed at a slow setting and in an open area away from obstacles.

WARNING

DO NOT allow operation of the machine by untrained personnel.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions Snapper From PreviousMaintenance Table of Contents Differ from your specific model. Contact Are provided for reference only and mayYour Snapper dealer if you have questions IntroductionSafety Messages and Symbols RUN PRE-START Check List Operating InstructionsStarting Engine Starting & Stopping ENGINE, BLADES, Parking BrakeStarting Mower Blades Stopping EngineStopping Mower Blades Parking BrakeOPERATION- Motion Controls Driving Machine Cutting Height AdjustmentEngine Must not Start if Stopping MachineEngine should Start if Engine Must Begin to Stop ifCheck Mower Blade Service After First 5 HoursAfter Every 25 Operating Hours 4.3.1. Engine Riding Mower Lubrication Before Operating MachineAnnually END of Each Season Deck Removal See Figure Neutral Position Adjustments Adjustments & RepairMower Deck & Component Adjustments Neutral Position Adjustments From PreviousMower Deck Adjustment Levelness Side to Side and Front to RearHighest cutting position and recheck side to side Parking Brake AdjustmentTraction Belt Tension Traction Belt ReplacementMower Drive Belt Replacement Tracking AdjustmentBelt Replacement Belt RemovalBlade Sharpening Battery Battery Removal Battery InstallationBattery Charging Battery Testing NEW Battery Preparation 1.Remove battery from cartonState of Charge Digital Voltmeter Insert spindle shaft up through the bottom Bearing ReplacementHydraulic SYSTEM, Purging Problem Probable Cause Trouble Shooting on NextCorrective Action Machine Will Not Move MAINTENANCE/REPLACEMENT Parts Service Performed Each100 Number USE HRS SeasonDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series

NZM25612KWV, NZM19482KWV, NZM21522KWV, NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV, NZM27612KH, NZM21522KWV, NZM19482KWV, NZM25612KWV, NZM27612KH, NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV specifications

The Snapper series of zero-turn mowers, including models NZM25612KWV, NZM19482KWV, NZM21522KWV, and NZM27612KH, are designed to deliver optimal performance, exceptional comfort, and cutting-edge technology for residential and commercial lawn care. Each model presents unique characteristics tailored to different mowing needs, making them suitable for various landscaping tasks.

The NZM25612KWV stands out with its powerful 25 horsepower engine, coupled with a robust 52-inch cutting deck. The cutting height adjustment feature allows for precision mowing, enabling users to achieve their desired grass length effortlessly. This model is particularly appreciated for its impressive maneuverability, making it ideal for navigating around obstacles in large yards or commercial properties.

On the other hand, the NZM19482KWV offers a slightly smaller footprint with a 48-inch cutting deck powered by a 19 horsepower engine. This model is perfect for homeowners with smaller lawns while still providing the efficiency and speed of a zero-turn mower. The compact design allows for easy storage, while the comfortable seating and intuitive controls contribute to a seamless mowing experience.

The NZM21522KWV combines the best of both worlds, featuring a 22 horsepower engine and a 54-inch cutting deck. This model is designed for those who require a balance between power and cutting width, making it versatile for both residential and commercial use. Additionally, its advanced vibration-dampening technology ensures comfort, even during extended mowing sessions.

Then there's the NZM27612KH, which boasts an impressive 27 horsepower engine paired with a 60-inch cutting deck. This powerhouse model is specifically engineered for large properties and professional landscapers who demand reliability and efficiency. With an expanded fuel tank and heavy-duty construction, it tackles extensive mowing tasks with ease, providing a crisp and clean cut every time.

In terms of technology, all the Snapper models incorporate user-friendly features such as electric deck lift options, easy-to-read LED displays for monitoring speed and battery life, and enhanced safety mechanisms. These models are also built with high-quality materials, ensuring durability and longevity in performance. Special attention is given to ease of maintenance, with accessible components for quick servicing and repairs.

Overall, Snapper mowers like the NZM25612KWV, NZM19482KWV, NZM21522KWV, and NZM27612KH not only elevate the gardening experience through their innovative design and advanced engineering but also enhance productivity for both at-home lawn care enthusiasts and professional landscapers alike.
Top Page Image Contents