Snapper NZM25612KWV, NZM19482KWV, NZM21522KWV, NZM27612KH important safety instructions

Page 15

Section 4 - MAINTENANCE

4.2.3.CHECK MOWER DRIVE BELT 1. Lower deck to lowest setting.

2. Remove footrest. See Figure 4.3.

3. Removal of footrest will allow access to deck belt.

4. Check the belt tension. The idler pulleys and springs provide proper belt tension and require no adjustments. If belt is frayed, slit, severed or belt strands exposed, replace belt before operating mower.

LIFT FOOT REST UP AND OFF POWER UNIT

FRAME TO GAIN ACCESS TO MOWER BELT

FIGURE 4.3

4.3AFTER EVERY 25 OPERATING HOURS 4.3.1. ENGINE

1. Engine Oil

Change engine oil. Refer to Section “CHANGE ENGINE OIL”. Refer to engine owner’s manual for oil specifications.

2. Air Filter

Refer to engine owner’s manual for service instructions.

4.3.2.MOWER COMPONENTS 1. Mower Drive Belt

No adjustment required. Replace belt as needed.

2. Mower Blade

Check blade for sharpness, wear, damage, and torque. Refer to Section “MOWER BLADE REPLACEMENT”.

3. Mower Deck Levelness

Check mower deck for proper levelness. Adjust as required. Refer to Section “MOWER DECK ADJUSTMENT – LEVELNESS”.

4. Clean Mower Deck

a.Remove key from ignition switch.

b.Remove spark plug wire(s) and secure away from spark plug(s).

c.Raise mower deck to its highest setting. It may be necessary to raise mower deck higher using a hydraulic floor jack. Secure machine with safety blocks.

d.Clean underside of mower deck, removing all accumulation of grass clippings and debris.

e.Clean top of deck, removing all grass clippings and debris.

5.Mower Blade Spindle - Lubrication a. Remove footrest.

b. Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, from a grease gun until grease purges from vent located on spindle housing underneath deck. See Figure 4.4.

LUBRICATE

SPINDLE

ASSEMBLIES

FIGURE 4.4

6. Mower Deck Linkage - Lubrication

Lubricate all mower deck linkage pivot points with a light coat of motor oil.

WARNING

DO NOT attempt any maintenance, adjustments or service with engine running. STOP engine. STOP blades. Set brake. Remove key. Remove spark plug wires and secure away from spark plugs. Engine and components are HOT. Avoid serious burns, allow sufficient time for all parts to cool.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions Snapper From PreviousMaintenance Table of Contents Introduction Are provided for reference only and mayDiffer from your specific model. Contact Your Snapper dealer if you have questionsSafety Messages and Symbols RUN PRE-START Check List Operating InstructionsStarting Engine Starting & Stopping ENGINE, BLADES, Parking BrakeParking Brake Stopping EngineStarting Mower Blades Stopping Mower BladesOPERATION- Motion Controls Driving Machine Cutting Height AdjustmentEngine Must Begin to Stop if Stopping MachineEngine Must not Start if Engine should Start ifCheck Mower Blade Service After First 5 HoursAfter Every 25 Operating Hours 4.3.1. Engine Riding Mower Lubrication Before Operating MachineAnnually END of Each Season Deck Removal See Figure Neutral Position Adjustments Adjustments & RepairSide to Side and Front to Rear Neutral Position Adjustments From PreviousMower Deck & Component Adjustments Mower Deck Adjustment LevelnessHighest cutting position and recheck side to side Parking Brake AdjustmentTraction Belt Tension Traction Belt ReplacementBelt Removal Tracking AdjustmentMower Drive Belt Replacement Belt ReplacementBlade Sharpening Battery Battery Removal Battery InstallationBattery Charging Battery Testing NEW Battery Preparation 1.Remove battery from cartonState of Charge Digital Voltmeter Insert spindle shaft up through the bottom Bearing ReplacementHydraulic SYSTEM, Purging Problem Probable Cause Trouble Shooting on NextCorrective Action Machine Will Not Move Number USE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts 100Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series

NZM25612KWV, NZM19482KWV, NZM21522KWV, NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV, NZM27612KH, NZM21522KWV, NZM19482KWV, NZM25612KWV, NZM27612KH, NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV specifications

The Snapper series of zero-turn mowers, including models NZM25612KWV, NZM19482KWV, NZM21522KWV, and NZM27612KH, are designed to deliver optimal performance, exceptional comfort, and cutting-edge technology for residential and commercial lawn care. Each model presents unique characteristics tailored to different mowing needs, making them suitable for various landscaping tasks.

The NZM25612KWV stands out with its powerful 25 horsepower engine, coupled with a robust 52-inch cutting deck. The cutting height adjustment feature allows for precision mowing, enabling users to achieve their desired grass length effortlessly. This model is particularly appreciated for its impressive maneuverability, making it ideal for navigating around obstacles in large yards or commercial properties.

On the other hand, the NZM19482KWV offers a slightly smaller footprint with a 48-inch cutting deck powered by a 19 horsepower engine. This model is perfect for homeowners with smaller lawns while still providing the efficiency and speed of a zero-turn mower. The compact design allows for easy storage, while the comfortable seating and intuitive controls contribute to a seamless mowing experience.

The NZM21522KWV combines the best of both worlds, featuring a 22 horsepower engine and a 54-inch cutting deck. This model is designed for those who require a balance between power and cutting width, making it versatile for both residential and commercial use. Additionally, its advanced vibration-dampening technology ensures comfort, even during extended mowing sessions.

Then there's the NZM27612KH, which boasts an impressive 27 horsepower engine paired with a 60-inch cutting deck. This powerhouse model is specifically engineered for large properties and professional landscapers who demand reliability and efficiency. With an expanded fuel tank and heavy-duty construction, it tackles extensive mowing tasks with ease, providing a crisp and clean cut every time.

In terms of technology, all the Snapper models incorporate user-friendly features such as electric deck lift options, easy-to-read LED displays for monitoring speed and battery life, and enhanced safety mechanisms. These models are also built with high-quality materials, ensuring durability and longevity in performance. Special attention is given to ease of maintenance, with accessible components for quick servicing and repairs.

Overall, Snapper mowers like the NZM25612KWV, NZM19482KWV, NZM21522KWV, and NZM27612KH not only elevate the gardening experience through their innovative design and advanced engineering but also enhance productivity for both at-home lawn care enthusiasts and professional landscapers alike.
Top Page Image Contents