Snapper NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV Maintenance

Page 4

IMPORTANT SAFETY INSTRUCTIONS

OPERATION

(Continued From Previous Page)

8.Keep hands and feet away from rotating blades underneath deck. DO NOT place foot on ground while BLADES are ON or machine is in motion.

9.DO NOT operate machine without entire grass catcher or guards in place. DO NOT point discharge at people, passing cars, windows or doors.

10.Slow down before turning.

11.Watch out for traffic when near or crossing roadways.

12.STOP engine immediately after striking an object or if an abnormal vibration occurs. Remove key. Remove and disconnect the sparkplug wire. Make necessary repairs before resuming operation.

13.Mow only in daylight or with good artificial light.

14.Move motion control levers SLOWLY to maintain control during speed and directional changes.

15.Exercise CAUTION when pulling loads. DO NOT pull loads greater than 300 pounds. Avoid jack knifing. DO NOT turn sharply. Attach loads to approved hitch point only following manufacturer’s instructions.

16.On slopes, the weight of towed equipment may cause loss of traction and loss of control. When towing travel slowly and allow extra distance to stop.

17.DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, an odorless and deadly poison.

MAINTENANCE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of children in a well ventilated, unoccupied building. Shut off fuel (when equipped with valve) while storing or transporting machine.

2.Clean grass and debris from engine, mufflers, drives and cutting units to help prevent overheating and fires. Clean up fuel, oil and excess grease.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Check brakes frequently; adjust, repair or replace as needed.

5.Keep all bolts, nuts and screws properly tight. Check that all cotter pins are in proper position.

MAINTENANCE

(Continued From Previous Column)

6.Always provide adequate ventilation when running engine. Engine exhaust gases contain carbon monoxide, an odorless and deadly poison.

7.Disconnect battery before performing maintenance or service. Cranking engine could cause injury. Disconnect negative (black) cable from battery first and positive (red) cable last. Reconnect positive first and negative last. Charge battery in an open, well ventilated area away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothing and insulated gloves.

8.Park machine on level ground. DO NOT work under machine without safety blocks.

9.Service engine and clean, adjust or repair only when engine and blades are stopped. Remove spark plug wire(s) from spark plug(s) and secure wire(s) away from spark plug(s).

10.DO NOT change engine governor speed settings or overspeed engine. DO NOT make adjustments with the engine running.

11.Lubricate machine at intervals specified in manual to prevent controls from binding.

12.Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them. Never straighten or weld blades, only replace them.

13.DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.

14.Carefully release pressure from components with stored energy.

15.Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices. Never allow untrained personnel to service machine.

16.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions From Previous SnapperMaintenance Table of Contents Are provided for reference only and may Differ from your specific model. ContactYour Snapper dealer if you have questions IntroductionSafety Messages and Symbols RUN Operating Instructions PRE-START Check ListStarting & Stopping ENGINE, BLADES, Parking Brake Starting EngineStopping Engine Starting Mower BladesStopping Mower Blades Parking BrakeCutting Height Adjustment OPERATION- Motion Controls Driving MachineStopping Machine Engine Must not Start ifEngine should Start if Engine Must Begin to Stop ifService After First 5 Hours Check Mower BladeAfter Every 25 Operating Hours 4.3.1. Engine Before Operating Machine Riding Mower LubricationAnnually END of Each Season Deck Removal See Figure Adjustments & Repair Neutral Position AdjustmentsNeutral Position Adjustments From Previous Mower Deck & Component AdjustmentsMower Deck Adjustment Levelness Side to Side and Front to RearParking Brake Adjustment Highest cutting position and recheck side to sideTraction Belt Replacement Traction Belt TensionTracking Adjustment Mower Drive Belt ReplacementBelt Replacement Belt RemovalBlade Sharpening Battery Installation Battery Battery RemovalBattery Charging NEW Battery Preparation 1.Remove battery from carton Battery TestingState of Charge Digital Voltmeter Bearing Replacement Insert spindle shaft up through the bottomHydraulic SYSTEM, Purging Trouble Shooting on Next Problem Probable CauseCorrective Action Machine Will Not Move Service Performed Each MAINTENANCE/REPLACEMENT Parts100 Number USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series

NZM25612KWV, NZM19482KWV, NZM21522KWV, NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV, NZM27612KH, NZM21522KWV, NZM19482KWV, NZM25612KWV, NZM27612KH, NZM27612KH, NZM19482KWV, NZM21522KWV, NZM25612KWV specifications

The Snapper series of zero-turn mowers, including models NZM25612KWV, NZM19482KWV, NZM21522KWV, and NZM27612KH, are designed to deliver optimal performance, exceptional comfort, and cutting-edge technology for residential and commercial lawn care. Each model presents unique characteristics tailored to different mowing needs, making them suitable for various landscaping tasks.

The NZM25612KWV stands out with its powerful 25 horsepower engine, coupled with a robust 52-inch cutting deck. The cutting height adjustment feature allows for precision mowing, enabling users to achieve their desired grass length effortlessly. This model is particularly appreciated for its impressive maneuverability, making it ideal for navigating around obstacles in large yards or commercial properties.

On the other hand, the NZM19482KWV offers a slightly smaller footprint with a 48-inch cutting deck powered by a 19 horsepower engine. This model is perfect for homeowners with smaller lawns while still providing the efficiency and speed of a zero-turn mower. The compact design allows for easy storage, while the comfortable seating and intuitive controls contribute to a seamless mowing experience.

The NZM21522KWV combines the best of both worlds, featuring a 22 horsepower engine and a 54-inch cutting deck. This model is designed for those who require a balance between power and cutting width, making it versatile for both residential and commercial use. Additionally, its advanced vibration-dampening technology ensures comfort, even during extended mowing sessions.

Then there's the NZM27612KH, which boasts an impressive 27 horsepower engine paired with a 60-inch cutting deck. This powerhouse model is specifically engineered for large properties and professional landscapers who demand reliability and efficiency. With an expanded fuel tank and heavy-duty construction, it tackles extensive mowing tasks with ease, providing a crisp and clean cut every time.

In terms of technology, all the Snapper models incorporate user-friendly features such as electric deck lift options, easy-to-read LED displays for monitoring speed and battery life, and enhanced safety mechanisms. These models are also built with high-quality materials, ensuring durability and longevity in performance. Special attention is given to ease of maintenance, with accessible components for quick servicing and repairs.

Overall, Snapper mowers like the NZM25612KWV, NZM19482KWV, NZM21522KWV, and NZM27612KH not only elevate the gardening experience through their innovative design and advanced engineering but also enhance productivity for both at-home lawn care enthusiasts and professional landscapers alike.
Top Page Image Contents