Snapper NZM21522KWV, NZM19482KWV, NZM25612KWV, NZM27612KH Battery Battery Removal

Page 25

Section 5 - ADJUSTMENTS & REPAIR

WARNING

Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal, which could cause sparks. Cables must be connected to battery terminals in the proper position. RED (Positive) cable must go to the ( + ) terminal. BLACK (Negative) cable must go to the ( - ) terminal. If battery is removed, DO NOT operate engine without insulating Positive + battery cable terminal with electrical tape, or sparking from the battery cables can result.

5.10BATTERY

5.10.1.BATTERY REMOVAL

1.Remove battery retainer. See Figure 5.17.

2.Slide terminal cover away from positive terminal.

3.Observe and note cable positions on battery. Disconnect cables from battery terminals, disconnecting BLACK (Negative) cable first and RED (Positive) last. Retain mounting bolts and nuts. See Figure 5.17.

REMOVE BATTERY RETAINER

DATE

FIGURE 5.17

5.10.2.BATTERY INSTALLATION

1.Position battery into battery compartment.

2.Connect cables to battery terminals. Connect RED (Positive) cable first. Connect BLACK (Negative) cable last. See Figure 5.18.

3.Reinstall battery retainer and positive terminal cover. See Figure 5.17.

BLACK (NEGATIVE) CABLE

RED (POSITIVE) CABLE

WHEN DISCONNECTING

TERMINAL COVER MUST

CABLES, DISCONNECT

SHIELD POSITIVE

NEGATIVE FIRST

TERMINAL AFTER

 

INSTALLATION

FIGURE 5.18

5.10.3.BATTERY CHARGING

NOTE: The battery in this machine is maintenance-free. It has been filled to the proper level with acid and is sealed. Do not attempt to open battery.

1.Remove battery.

2.Place battery in a well-ventilated area on a level, non-concrete surface.

3.Connect battery charger to battery terminals. RED to positive (+) terminal and BLACK to negative (-) terminal.

4.Slow charge battery at 6-10 amps for 1 hour.

5.If battery will not accept charge or is partially charged after 1 hour of charging, replace with new battery.

WARNING

Keep all sparks, flame and fire away from area when charging battery.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions Snapper From PreviousMaintenance Table of Contents Differ from your specific model. Contact Are provided for reference only and mayYour Snapper dealer if you have questions IntroductionSafety Messages and Symbols RUN PRE-START Check List Operating InstructionsStarting Engine Starting & Stopping ENGINE, BLADES, Parking BrakeStarting Mower Blades Stopping EngineStopping Mower Blades Parking BrakeOPERATION- Motion Controls Driving Machine Cutting Height AdjustmentEngine Must not Start if Stopping MachineEngine should Start if Engine Must Begin to Stop ifCheck Mower Blade Service After First 5 HoursAfter Every 25 Operating Hours 4.3.1. Engine Before Operating Machine Riding Mower LubricationAnnually END of Each Season Deck Removal See Figure Neutral Position Adjustments Adjustments & RepairMower Deck & Component Adjustments Neutral Position Adjustments From PreviousMower Deck Adjustment Levelness Side to Side and Front to RearHighest cutting position and recheck side to side Parking Brake Adjustment Traction Belt Tension Traction Belt ReplacementMower Drive Belt Replacement Tracking AdjustmentBelt Replacement Belt RemovalBlade Sharpening Battery Installation Battery Battery RemovalBattery Charging NEW Battery Preparation 1.Remove battery from carton Battery TestingState of Charge Digital Voltmeter Insert spindle shaft up through the bottom Bearing ReplacementHydraulic SYSTEM, Purging Trouble Shooting on Next Problem Probable CauseCorrective Action Machine Will Not Move MAINTENANCE/REPLACEMENT Parts Service Performed Each100 Number USE HRS SeasonDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series
Top Page Image Contents