Snapper 020230 user manual Nozzle Maintenance, Ring Maintenance

Page 14

2650 PSI Pressure Washer

1.Detach spray gun and nozzle extension from high pressure hose. Detach nozzle extension from spray gun and remove o-ring and screen from nozzle extension. Flush screen, spray gun, and nozzle extension with clean water to clear debris.

2.Place in-line filter screen into threaded end of nozzle extension. Direction does not matter. Push screen in with eraser end of pencil until it rests flat at bottom of opening.Take care to not bend screen.

3.Place o-ring into recess. Push o-ring snugly against in-line filter screen.

4.Assemble nozzle extension to spray gun, as described earlier in this manual.

5.Using a garden hose, remove additional debris by back flushing water through nozzle extension (Figure 15). Back flush between 30 to 60 seconds.

Figure 15 — Backflushing the Nozzle Extension

6.Reinstall spray tip and in-line filter into nozzle extension.

7.Reconnect nozzle extension to spray gun.

8.Reconnect water supply, turn on water, and start engine.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure.The principal cause of excessive pump pressure is a spray tip clogged or restricted with foreign materials, such as dirt, etc.To correct the problem, immediately clean the spray tip following these instructions:

1.Shut off engine and turn off water supply.

2.Remove spray tip from end of nozzle extension.

3.Remove in-line filter from other end of nozzle extension.

4.Use a small paper clip to free any foreign material clogging or restricting spray tip (Figure 14).

Figure 14 — Nozzle Maintenance

Use wire here

to remove

debris.

9.Test pressure washer by operating with each Quick Connect spray tips.

O–Ring Maintenance

Purchase an O–Ring/Maintenance Kit, part number 191922GS by contacting the nearest authorized service center. It is not included with the pressure washer.This kit includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service your unit’s o-rings.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

•NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents PSI Pressure Washer Equipment Description Table of ContentsSafety Rules When Adding Fuel Operate pressure washer only outdoorsReflective exhaust heat may damage fuel tank causing fire Unintentional sparking can result in fire or electric shockPump equipped with Automatic Cool Down System Safety Goggles not shown Always use the enclosedKnow Your Pressure Washer Preparing Pressure Washer for USE AssemblyCarton Contents Remove Pressure Washer From CartonAdd Engine Oil and Fuel Connect Hose and Water Supply to PumpChecklist Before Starting Engine Connect Garden Hose to Water InletPressure Washer Location HOW to USE Your Pressure WasherHow to Start Pressure Washer Pressure Washer ClearanceHow to Stop Your Pressure Washer Trigger LockLow Pressure How to Use Spray TipsHigh Pressure Cleaning and Applying Chemical Automatic Cool Down System Cleaning Detergent Siphoning TubePressure Washer Rinsing Thermal ReliefPressure Washer Maintenance SpecificationsGeneral Maintenance Recommendations Nozzle Maintenance Ring MaintenanceChanging Pump Oil Engine MaintenancePump Maintenance Change pump oil as followsStoring the Engine Always wear eye protection when using PumpSaverPreparing the Unit for Storage Protecting the PumpPSI Pressure Washer Troubleshooting Problem Cause CorrectionEquipment Consumer Use Commercial Use Snapper Owner Warranty Policy Effective August 1About your equipment warranty Portable Generator Years 2nd year parts onlyReglas DE Seguridad Tabla DE ContenidosDescripción DEL Equipo AdvertenciaCuando Añada Combustible Precaución Conozca SU Maquina Lavadora DE Presion Perilla del Cebador Usada para arranque de motores fríosRemueva el Lavador a Presión del Empaque MontajePreparando EL Lavador a Presión Para SU USO Contenido de la CajaGancho del Pistola Manguera Agregar Aceite al Motor y GasolinaConecte la Manguera y el Suministro de Agua a la Bomba Lista DE Revision Previa AL Arranque DEL Motor Cómo Darle Arranque a su Lavadora a Presión Cómo Usar SU Lavadora a PresiónUbicación del Lavadora a Presión Espacio Libre Alrededor del Lavadora a PresiónCómo Detener su Máquina Lavadora a Presión El Pasador de la SeguridadLa Presión Alta Cómo Usar las Puntas de RocíoLa Presión Baja Limpieza y Aplicación del QuímicoSistema de Enfriamiento Automático Alivio Térmico Enjuage de la Máquina Lavadora a PresiónLimpiando el Tubo Para EnjuageMantenimiento DE LA Maquina Lavadora a Presion EspecificacionesRecomendaciones Generales Mantenimiento de la Boquilla Mantenimiento de los Anillos OCambio del aceite de la bomba Mantenimiento DEL MotorMantenimiento de la Bomba Cambie el aceite como se indica a continuaciónProteger la Bomba Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Reparacion DE Averias Generador Portátil Efectiva desde el 1 ro de AgostoEquipo Para Uso Del Consumidor Para Uso Comercial Año

020230 specifications

Snapper 020230 is an advanced tool designed specifically for efficiency and precision in various applications, particularly within the landscaping and gardening sector. Known for its robust performance and innovative features, the Snapper 020230 has quickly gained popularity among both professionals and DIY enthusiasts.

One of the standout features of the Snapper 020230 is its powerful engine. Equipped with a reliable Briggs & Stratton engine, this tool delivers consistent power, making it capable of handling tough mowing tasks with ease. The engine is designed for optimal performance, offering high torque and fuel efficiency, allowing users to achieve longer operating times without frequent refueling.

The design of the Snapper 020230 emphasizes user comfort and control. It boasts an ergonomic handle that provides a comfortable grip, reducing fatigue during prolonged use. The adjustable height settings allow users to customize the cutting height according to their preferences, ensuring a clean and even cut every time.

Another significant characteristic is the cutting deck, which measures 21 inches in width. This size is perfectly balanced for maneuverability and efficiency, allowing users to navigate tight spaces while still covering substantial ground. The deck design also incorporates a mulching feature, enabling grass clippings to be finely chopped and returned to the lawn, promoting healthier growth.

In addition to its physical features, the Snapper 020230 integrates modern technologies that enhance its functionality. The easy-start system is designed to minimize the effort needed to start the engine, ensuring that users can get to work quickly. Moreover, the dual-bagging system enables efficient collection of grass clippings, reducing clean-up time.

Durability is another key characteristic of the Snapper 020230. Constructed with high-quality materials, this tool is built to withstand the rigors of regular use in challenging outdoor conditions. Its rust-resistant components ensure longevity while maintaining peak performance through various weather scenarios.

Overall, the Snapper 020230 stands out for its powerful engine, user-friendly design, and advanced technologies. Whether for commercial landscaping projects or personal gardening, this tool is engineered to deliver exceptional results, making it a worthy investment for anyone looking to enhance their lawn care experience. With its combination of efficiency, durability, and innovative features, the Snapper 020230 is a reliable choice for any outdoor enthusiast.
Top Page Image Contents