Cub Cadet 6284 manual Operation, Rollover Protective Structure Rops, Folding the Rops

Page 15

SECTION 2: OPERATION

ROLLOVER PROTECTIVE STRUCTURE (ROPS)

This tractor is equipped with a foldable Rollover Protection Structure (ROPS) and seat belts. When used together they are effective in reducing injuries to the operator in the event of an accidental tractor rollover. The safety provided by the ROPS is minimized if the seat belt is not properly adjusted AND buckled. Refer to ADJUSTMENTS for seat belt adjustment.

ROPS

Figure 12

WARNING: Always wear the seat belt when operating the tractor equipped with a ROPS. However, if the ROPS is in the folded position or has been re- moved, the seat belt must not be used.

Use the following guidelines when using a tractor equipped with a ROPS:

•Be aware of overhead clearances in the area of operation. Check for clearance of door (or gate) openings and other overhead objects such as utility lines and tree branches. Overhead objects could catch the ROPS and upset the tractor.

•Do not modify the ROPS by drilling holes for, or welding accessories to the structure.

•Do not use the ROPS to pull objects with the tractor. Use ONLY the tractor drawbar for pulling.

•In the event of an accident, have the ROPS carefully inspected and, if necessary, replaced by your Cub Cadet dealer. Do not attempt to repair the ROPS.

FOLDING THE ROPS

The foldable ROPS feature allows the operator to quickly lower the ROPS to operate in areas where there is low overhead clearance. However, the ROPS should be used in the lowered position only when absolutely necessary. Operate with the ROPS in the ‘up’ position whenever possible.

WARNING: A folded ROPS does not provide rollover protection. When the ROPS is in the folded position, the seat belt must NOT be used.

Reposition the ROPS as follows:

•Slightly loosen the two hex jam nuts on the two hex screws in the front of the upper ROPS. Loosen the hex screws to relieve their pressure on the ROPS. See Figure 13.

•Remove the two internal cotter pins, and, while supporting the ROPS, withdraw the clevis pins. See Figure 13. Carefully lower the ROPS.

•Reinstall the clevis pins and cotter pins for storage.

HEX

SCREW

JAM

NUT

 

INTERNAL

 

 

HEX

 

 

 

SCREW

 

COTTER PIN

 

 

 

 

CLEVIS

 

 

 

JAM

PIN

 

 

 

 

 

 

NUT

 

 

 

 

CLEVIS

PIN

Figure 13

To raise the ROPS:

•Remove internal cotter pins and clevis pins and lift the ROPS into position.

•Insert the clevis pins and secure with the internal cotter pins.

•Tighten the hex screws against the ROPS, then tighten the hex jam locknuts.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operator’s Manual Important Read Safety Rules and Instructions CarefullyTable of Contents Calling Service InformationTo the Owner Recording Model and Serial Number Information Tractor Model PlateRops Information Plate General Operation Important Safe Operation PracticesDo not Slope OperationSafety Frame Rops Warni NG Safety Labels Floorboard and Dash Panel Mounted Controls Controls and FeaturesSteering Wheel PTO SwitchIgnition Switch Seat Adjustment LeverParking Brake Lever Hazard Light SwitchHeadlight Switch Differential Lock PedalBrake Engaged Indicator Battery Indicator LightOil Pressure Indicator PTO Engaged IndicatorPTO Selection Lever Fender Mounted Conrtols and FeaturesPTO Reverse Override Switch Fuel Fill CapAmber Hazard Lights Transmission Hi/Lo Range Shift LeverCup Holder Hand HoldsOperation Rollover Protective Structure RopsFolding the Rops Safety Interlock System NEW Tractor BREAK-IN ProceduresFueling the Tractor Stopping the Engine Using Jumper Cables to Start EngineStarting the Engine Cold Weather StartingStopping the Tractor Using the FORWARD/REVERSE PedalDriving the Tractor Driving on SlopesUsing the HI/LO Range Shift Lever Using the Differential Lock PedalLOW Using the Hydraulic Lift Lever Using the PTO Selection LeverEngaging the PTO Lighting Using the PTO Reverse Override SwitchUsing the TOP Link Retainer Hook Hazard LightsUsing the Auxiliary Hydraulic Control Handle Using the Three Point HitchUsing the Auxiliary Hydraulic Valve Using the Hitch PlateOn Demand Four Wheel Drive Tractor WeightingThree Point Hitch Adjustments AdjustmentsAdjusting the Seat Adjusting the Seat BeltCheck the TOE-IN AS Follows Adjusting Front Wheel TOE-INAdjusting Hydraulic Lift Feedback ROD Adjusting the BrakesGeneral Information MaintenanceLubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart General Battery Information Accessing the Engine CompartmentBattery Storage Battery RemovalCharging the Battery Battery MaintenanceHead Light Bulb Replacement Tail LIGHT/HAZARD Light Bulb ReplacementServicing Electrical System Right Side Accessing the Lower Dash Panel AreaChecking/Replacing Fuses Electrical Circuit RelaysChecking TRANSMISSION/HYDRAULIC System OIL Level Hazard Light Flasher RelayChanging TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter ChangeCheck Front Axle Oil Regularly Scheduled Oil Filter ChangesChanging Front Axle and Final Reduction Gear Case OIL Check Final Reduction Gear Case OilLubrication of FWD Drive Shaft Maintenance of the Rollover Protective Structure RopsTire Maintenance Lubrication of Main Drive ShaftRemoving the Tractor from Storage Tractor StorageCleaning the Engine Cleaning RADIATOR/RADIATOR ScreenChecking Engine OIL Level Changing the Engine OIL and Filter Adding Engine OILChecking Engine Coolant Level Changing the AIR Cleaner Inspection of Cooling System HosesChanging the Engine Coolant Servicing the Fuel Filter Draining The Fuel FilterChanging The Fuel Filter Fuel Injector Nozzle Service Engine Breather ServiceSpecifications Brakes Power Take-OffGeneral Dimensions Hydraulic Lift SystemDescription Model Number Optional Equipment and AccessoriesPage Page Page CLEVELAND, Ohio CUB Cadet LLC Post Office BOX

6284 specifications

The Cub Cadet 6284 is a robust utility tractor known for its versatility and reliability. Designed for both residential and commercial use, it is ideal for tasks such as landscaping, gardening, and light agricultural work. This model stands out in the compact tractor market due to its powerful engine and innovative features that boost productivity and ease of use.

At the heart of the Cub Cadet 6284 lies a powerful 28-horsepower Kohler diesel engine, which provides ample torque for demanding applications. This engine is designed for efficiency and durability, ensuring long-lasting performance and reduced operating costs. The liquid-cooled design helps to maintain optimal operating temperatures, extended engine life, and consistent power output, making it suitable for various weather conditions.

One of the key characteristics of the 6284 is its hydrostatic transmission, which offers seamless shifting without the need for clutching. This feature allows operators to maintain a steady pace while maneuvering in tight spaces or during intricate tasks. The intuitive controls enhance user experience, making it an excellent choice for both seasoned operators and newcomers alike.

The 6284 features a heavy-duty, rear-mounted three-point hitch with a standard lift capacity which enables the attachment of various implements, enhancing its versatility. With a variety of compatible attachments, including rotary cutters, plows, and loaders, users can easily switch between tasks, making it a multifunctional workhorse.

Another notable technology integrated into the Cub Cadet 6284 is the ergonomic operator station. The layout is designed with user comfort in mind, featuring an adjustable seat, easy-to-reach controls, and excellent visibility, allowing operators to work efficiently for extended periods. The compact design aids in maneuverability, especially in more confined spaces.

Additionally, the Cub Cadet 6284 is built with a sturdy frame and quality materials, designed to withstand heavy use. The all-steel construction contributes to its overall durability, ensuring that the tractor can handle tough jobs without compromising performance.

In summary, the Cub Cadet 6284 is a powerful and efficient compact utility tractor that offers reliable performance for a variety of tasks. Its combination of a robust engine, hydrostatic transmission, and ergonomic design makes it a valuable addition to any toolkit. Whether for residential gardening or more extensive commercial applications, the 6284 is equipped to tackle the job with ease and efficiency.
Top Page Image Contents