Cub Cadet 6284 manual Adjusting the Seat Belt, Three Point Hitch Adjustments

Page 24

SECTION 3: ADJUSTMENTS

ADJUSTING THE SEAT

For the comfort of the operator, a single lever adjustable seat is provided to set the fore to aft position of the seat. Adjust the seat to the most comfortable position that allows you to operate all controls and pedals.

WARNING: Do not adjust the seat when the tractor is moving, as this could cause the operator to lose momentary control of the tractor and result in an accident.

•To adjust the seat, pivot the seat adjustment lever to the left and hold while repositioning the seat to the desired position.

•After repositioning the seat, release the lever to lock the seat in position. Slide the seat either slightly forward or rearward to assure it is locked or until engagement of the lock is felt. See Figure 25.

 

Pivot Lever

SEAT

to Left

ADJUSTMENT

LEVER

Figure 25

ADJUSTING THE SEAT BELT

WARNING: Always wear the seat belt when operating the tractor equipped with a ROPS. However, if the ROPS has been folded down, or removed, the seat belt should not be used.

NOTE: If the belt is too long or too short to be prop- erly adjusted using the upper belt webbing, the adjustment clip should be repositioned. To do so, firmly grasp the adjustment clip and pull the lower webbing though the clip. Move the clip toward the anchor point at the seat to shorten the belt, or toward the buckle link the lengthen the belt.

Adjust the final length of the seat belt using the adjuster clip, buckle link, and upper belt webbing on the right half of the belt.

To lengthen the belt:

•Hold the ends of the adjuster clip and tip upward the side of the clip toward the buckle link. While holding the clip, pull the upper webbing of the belt through the clip toward the buckle link. See Figure 26.

•Hold the belt and pull the buckle link to the left to remove the slack in the upper webbing of the belt between the adjuster clip and the link.

BUCKLE Tip Sides of Clip

RELEASE

BUTTONPull Belt to Pull Belt to

Lengthen Shorten

BUCKLE

 

 

 

 

 

 

 

ADJUSTER

 

 

 

 

 

 

 

CLIP

LINK

 

UPPER

 

 

 

 

 

LOWER

 

 

 

 

WEBBING

 

 

 

WEBBING

Figure 26

•To shorten the belt, tip the other side of the clip upward, pull the free end of the belt webbing to the right, and pull the buckle link to the left to remove the slack.

THREE POINT HITCH ADJUSTMENTS

•Adjust the RH adjustable lift link to level the lower hitch links. Loosen the jam nut and turn the adjustment tube as shown in Figure 27 to shorten or lengthen the lift link. Tighten the jam nut against the adjustment tube after adjusting.

Loosen

JAM

Jam Nut

NUT

ADJUSTMENT

Shorten TUBE

Lengthen

Figure 27

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualTable of Contents Calling Service InformationTo the Owner Recording Model and Serial Number Information Tractor Model PlateRops Information Plate Important Safe Operation Practices General OperationSlope Operation Do notSafety Frame Rops Warni NG Safety Labels Controls and Features Floorboard and Dash Panel Mounted ControlsPTO Switch Ignition SwitchSeat Adjustment Lever Steering WheelHazard Light Switch Headlight SwitchDifferential Lock Pedal Parking Brake LeverBattery Indicator Light Oil Pressure IndicatorPTO Engaged Indicator Brake Engaged IndicatorFender Mounted Conrtols and Features PTO Reverse Override SwitchFuel Fill Cap PTO Selection LeverTransmission Hi/Lo Range Shift Lever Cup HolderHand Holds Amber Hazard LightsOperation Rollover Protective Structure RopsFolding the Rops Safety Interlock System NEW Tractor BREAK-IN ProceduresFueling the Tractor Using Jumper Cables to Start Engine Starting the EngineCold Weather Starting Stopping the EngineUsing the FORWARD/REVERSE Pedal Driving the TractorDriving on Slopes Stopping the TractorUsing the HI/LO Range Shift Lever Using the Differential Lock PedalLOW Using the Hydraulic Lift Lever Using the PTO Selection LeverEngaging the PTO Using the PTO Reverse Override Switch Using the TOP Link Retainer HookHazard Lights LightingUsing the Three Point Hitch Using the Auxiliary Hydraulic ValveUsing the Hitch Plate Using the Auxiliary Hydraulic Control HandleTractor Weighting On Demand Four Wheel DriveAdjustments Adjusting the SeatAdjusting the Seat Belt Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes Adjusting Hydraulic Lift Feedback RODMaintenance General InformationLubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart Accessing the Engine Compartment General Battery InformationBattery Removal Charging the BatteryBattery Maintenance Battery StorageHead Light Bulb Replacement Tail LIGHT/HAZARD Light Bulb ReplacementServicing Electrical System Accessing the Lower Dash Panel Area Checking/Replacing FusesElectrical Circuit Relays Right SideHazard Light Flasher Relay Checking TRANSMISSION/HYDRAULIC System OIL LevelInitial Break-In Period Filter Change Changing TRANSMISSION/HYDRAULIC System OILRegularly Scheduled Oil Filter Changes Check Front Axle OilCheck Final Reduction Gear Case Oil Changing Front Axle and Final Reduction Gear Case OILMaintenance of the Rollover Protective Structure Rops Tire MaintenanceLubrication of Main Drive Shaft Lubrication of FWD Drive ShaftTractor Storage Removing the Tractor from StorageCleaning the Engine Cleaning RADIATOR/RADIATOR ScreenChecking Engine OIL Level Adding Engine OIL Changing the Engine OIL and FilterChecking Engine Coolant Level Changing the AIR Cleaner Inspection of Cooling System HosesChanging the Engine Coolant Servicing the Fuel Filter Draining The Fuel FilterChanging The Fuel Filter Engine Breather Service Fuel Injector Nozzle ServiceSpecifications Power Take-Off General DimensionsHydraulic Lift System BrakesOptional Equipment and Accessories Description Model NumberPage Page Page CUB Cadet LLC Post Office BOX CLEVELAND, Ohio

6284 specifications

The Cub Cadet 6284 is a robust utility tractor known for its versatility and reliability. Designed for both residential and commercial use, it is ideal for tasks such as landscaping, gardening, and light agricultural work. This model stands out in the compact tractor market due to its powerful engine and innovative features that boost productivity and ease of use.

At the heart of the Cub Cadet 6284 lies a powerful 28-horsepower Kohler diesel engine, which provides ample torque for demanding applications. This engine is designed for efficiency and durability, ensuring long-lasting performance and reduced operating costs. The liquid-cooled design helps to maintain optimal operating temperatures, extended engine life, and consistent power output, making it suitable for various weather conditions.

One of the key characteristics of the 6284 is its hydrostatic transmission, which offers seamless shifting without the need for clutching. This feature allows operators to maintain a steady pace while maneuvering in tight spaces or during intricate tasks. The intuitive controls enhance user experience, making it an excellent choice for both seasoned operators and newcomers alike.

The 6284 features a heavy-duty, rear-mounted three-point hitch with a standard lift capacity which enables the attachment of various implements, enhancing its versatility. With a variety of compatible attachments, including rotary cutters, plows, and loaders, users can easily switch between tasks, making it a multifunctional workhorse.

Another notable technology integrated into the Cub Cadet 6284 is the ergonomic operator station. The layout is designed with user comfort in mind, featuring an adjustable seat, easy-to-reach controls, and excellent visibility, allowing operators to work efficiently for extended periods. The compact design aids in maneuverability, especially in more confined spaces.

Additionally, the Cub Cadet 6284 is built with a sturdy frame and quality materials, designed to withstand heavy use. The all-steel construction contributes to its overall durability, ensuring that the tractor can handle tough jobs without compromising performance.

In summary, the Cub Cadet 6284 is a powerful and efficient compact utility tractor that offers reliable performance for a variety of tasks. Its combination of a robust engine, hydrostatic transmission, and ergonomic design makes it a valuable addition to any toolkit. Whether for residential gardening or more extensive commercial applications, the 6284 is equipped to tackle the job with ease and efficiency.
Top Page Image Contents