Cub Cadet 6284 manual Slope Operation, Do not

Page 5

Maintain the weight balance of the tractor. Install front end weights to counterbalance heavy implements attached to the three point hitch. Do not operate the tractor with a light front end.

Any towed vehicle with a total weight exceeding that of the tractor should be equipped its own braking system that is operational from the tractor seat.

Do not leave equipment in the raised position.

Watch for traffic when operating near or crossing roadways. If local laws permit road travel, use the flashing hazard lights and SMV signs when traveling on public roadways.

Make certain all tractor lights are illuminated when operating at night.

Always watch where you are going, especially at blind corners, trees, or other objects that can obscure your vision.

Check overhead clearance carefully before driving under power lines, wires, bridges or low hanging tree branches, before entering or leaving buildings, or in any other situation where the operator and/or roll bar may be struck, which could result in serious injury.

To avoid upsets, drive the tractor with care and at a safe speed. Use extra caution when operating over rough ground, when crossing ditches or slopes, and when turning corners.

If the tractor becomes stuck, use reverse to free the tractor to prevent tractor upset.

2. SLOPE OPERATION

Slopes are a major factor related to loss of control and tip-over accidents which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not operate this unit on that area or serious injury could result.

DO:

Operate up and down slopes, not across.

Remove obstacles such as rocks, limbs, etc.

Watch for holes, ruts or bumps. Uneven terrain could overturn the machine. Tall grass can hide such obstacles.

Place the transmission in the low range. when climbing or descending slopes. Always keep machine in gear when going down slopes to take advantage of engine braking action.

Follow the manufacturers recommendations for counterweights to improve stability.

Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction. Rapid engagement or braking could cause the front of the machine to lift and rapidly flip over backwards which could cause serious injury.

Avoid starting or stopping on a slope. If tires lose traction, disengage the PTO and proceed slowly straight down the slope.

DO NOT:

Do not turn on slopes unless necessary; then, turn slowly and gradually downhill, if possible.

Do not mow near drop-offs, ditches or embankments. The mower could suddenly turn over if a wheel goes over the edge of a cliff or ditch, or if an edge caves in.

3. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine. Never assume children will remain where you last saw them.

Keep children out of the operating area and in watchful care of an adult other than the operator.

Be alert and turn machine off if children enter the area.

Before and when backing, look behind and down for small children.

To avoid back-over accidents, always disen- gage the cutting blades before shifting in re- verse. The PTO Reverse switch should not be "ON" when children or others are around.

Never carry children. They may fall off and be seriously injured or interfere with safe machine operation.

Never allow children under 14 years old to operate the machine. Children 14 years and over should only operate machine under close parental supervision and proper instruction.

Use extra care when approaching blind corners, shrubs, trees or other objects that may obscure your vision of a child or other hazard.

Remove key when machine is unattended to prevent unauthorized operation.

4. OPERATING THE PTO

When operating PTO driven equipment, disengage the PTO, stop the engine, and wait until the PTO stops before dismounting the tractor and disconnecting the equipment.

Do not wear loose fitting clothing when operat- ing the PTO or when near rotating equipment.

5

Image 5
Contents Operator’s Manual Important Read Safety Rules and Instructions CarefullyTo the Owner Table of ContentsCalling Service Information Rops Information Plate Recording Model and Serial Number InformationTractor Model Plate General Operation Important Safe Operation PracticesDo not Slope OperationSafety Frame Rops Warni NG Safety Labels Floorboard and Dash Panel Mounted Controls Controls and FeaturesIgnition Switch PTO SwitchSeat Adjustment Lever Steering WheelHeadlight Switch Hazard Light SwitchDifferential Lock Pedal Parking Brake LeverOil Pressure Indicator Battery Indicator LightPTO Engaged Indicator Brake Engaged IndicatorPTO Reverse Override Switch Fender Mounted Conrtols and FeaturesFuel Fill Cap PTO Selection LeverCup Holder Transmission Hi/Lo Range Shift LeverHand Holds Amber Hazard LightsFolding the Rops OperationRollover Protective Structure Rops Fueling the Tractor Safety Interlock SystemNEW Tractor BREAK-IN Procedures Starting the Engine Using Jumper Cables to Start EngineCold Weather Starting Stopping the EngineDriving the Tractor Using the FORWARD/REVERSE PedalDriving on Slopes Stopping the TractorLOW Using the HI/LO Range Shift LeverUsing the Differential Lock Pedal Engaging the PTO Using the Hydraulic Lift LeverUsing the PTO Selection Lever Using the TOP Link Retainer Hook Using the PTO Reverse Override SwitchHazard Lights LightingUsing the Auxiliary Hydraulic Valve Using the Three Point HitchUsing the Hitch Plate Using the Auxiliary Hydraulic Control HandleOn Demand Four Wheel Drive Tractor WeightingAdjusting the Seat AdjustmentsAdjusting the Seat Belt Three Point Hitch AdjustmentsCheck the TOE-IN AS Follows Adjusting Front Wheel TOE-INAdjusting Hydraulic Lift Feedback ROD Adjusting the BrakesGeneral Information MaintenanceLubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart General Battery Information Accessing the Engine CompartmentCharging the Battery Battery RemovalBattery Maintenance Battery StorageServicing Electrical System Head Light Bulb ReplacementTail LIGHT/HAZARD Light Bulb Replacement Checking/Replacing Fuses Accessing the Lower Dash Panel AreaElectrical Circuit Relays Right SideChecking TRANSMISSION/HYDRAULIC System OIL Level Hazard Light Flasher RelayChanging TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter ChangeCheck Front Axle Oil Regularly Scheduled Oil Filter ChangesChanging Front Axle and Final Reduction Gear Case OIL Check Final Reduction Gear Case OilTire Maintenance Maintenance of the Rollover Protective Structure RopsLubrication of Main Drive Shaft Lubrication of FWD Drive ShaftRemoving the Tractor from Storage Tractor StorageChecking Engine OIL Level Cleaning the EngineCleaning RADIATOR/RADIATOR Screen Changing the Engine OIL and Filter Adding Engine OILChecking Engine Coolant Level Changing the Engine Coolant Changing the AIR CleanerInspection of Cooling System Hoses Changing The Fuel Filter Servicing the Fuel FilterDraining The Fuel Filter Fuel Injector Nozzle Service Engine Breather ServiceSpecifications General Dimensions Power Take-OffHydraulic Lift System BrakesDescription Model Number Optional Equipment and AccessoriesPage Page Page CLEVELAND, Ohio CUB Cadet LLC Post Office BOX

6284 specifications

The Cub Cadet 6284 is a robust utility tractor known for its versatility and reliability. Designed for both residential and commercial use, it is ideal for tasks such as landscaping, gardening, and light agricultural work. This model stands out in the compact tractor market due to its powerful engine and innovative features that boost productivity and ease of use.

At the heart of the Cub Cadet 6284 lies a powerful 28-horsepower Kohler diesel engine, which provides ample torque for demanding applications. This engine is designed for efficiency and durability, ensuring long-lasting performance and reduced operating costs. The liquid-cooled design helps to maintain optimal operating temperatures, extended engine life, and consistent power output, making it suitable for various weather conditions.

One of the key characteristics of the 6284 is its hydrostatic transmission, which offers seamless shifting without the need for clutching. This feature allows operators to maintain a steady pace while maneuvering in tight spaces or during intricate tasks. The intuitive controls enhance user experience, making it an excellent choice for both seasoned operators and newcomers alike.

The 6284 features a heavy-duty, rear-mounted three-point hitch with a standard lift capacity which enables the attachment of various implements, enhancing its versatility. With a variety of compatible attachments, including rotary cutters, plows, and loaders, users can easily switch between tasks, making it a multifunctional workhorse.

Another notable technology integrated into the Cub Cadet 6284 is the ergonomic operator station. The layout is designed with user comfort in mind, featuring an adjustable seat, easy-to-reach controls, and excellent visibility, allowing operators to work efficiently for extended periods. The compact design aids in maneuverability, especially in more confined spaces.

Additionally, the Cub Cadet 6284 is built with a sturdy frame and quality materials, designed to withstand heavy use. The all-steel construction contributes to its overall durability, ensuring that the tractor can handle tough jobs without compromising performance.

In summary, the Cub Cadet 6284 is a powerful and efficient compact utility tractor that offers reliable performance for a variety of tasks. Its combination of a robust engine, hydrostatic transmission, and ergonomic design makes it a valuable addition to any toolkit. Whether for residential gardening or more extensive commercial applications, the 6284 is equipped to tackle the job with ease and efficiency.