Cub Cadet Essential Guide for 6284 Bulb Replacement and Troubleshooting
Page 32

HEAD LIGHT BULB REPLACEMENT

The tractor is equipped with four headlight bulbs. If one of the bulbs should burn out, replace the bulb as follows:

•Remove the taillight bulb by simply pulling the bulb from the taillight socket. Replace with a like bulb. Align the bulb terminals with the socket terminals, and push the new bulb fully into the socket. Refer to Figure 38.

•Fully raise the hood so that the hood prop cylinders hold the hood in the raised position.

•Pull both locking tabs of the wire harness plug away from the bulb/socket assembly and unplug the wire harness from the bulb assembly. See Figure 37.

BULB/SOCKET

ASSEMBLY.

WIRE

SOCKET SLOT

TAILLIGHT SOCKET

HOUSING

HAZZARD

SOCKET

HAZZARD

BULB

TAILLIGHT

BULB

HARNESS REFLECTOR

PLUG

LOCKING TAB

Figure 37

•Turn the bulb/socket assembly approximately a quarter turn counterclockwise to align its tabs with the notches of the reflector, then remove from the reflector.

•Replace with a new bulb/socket assembly (Cub Cadet No. 725-3161A).

•Align the tabs of the new bulb/socket assembly with the notches of the reflector and insert the bulb.

•Turn the bulb/socket assembly clockwise to lock in place. Plug the wire harness into the socket, making sure the plug locking tabs lock onto the socket assembly.

TAIL LIGHT/HAZARD LIGHT BULB

REPLACEMENT

Each hazzard light assembly has two light bulbs — the hazzard light bulb and the taillight bulb. Replace the taillight bulb or hazzard light bulb as follows:

•Remove the two screws fastening the rear lense (amber and red) to the hazzard light housing.

Figure 38

•To remove the hazzard bulb, push the bulb upward in the socket and turn counterclockwise to remove the bulb from the light socket. Refer to Figure 38.

•Replace with a like bulb.

•Align the post of the new bulb with the slot in the socket, push the bulb into the socket, and turn clockwise to lock it in the socket.

•Position the rear lense in the housing and secure with the two screws removed earlier.

SERVICING ELECTRICAL SYSTEM

Fuses are installed to protect the tractor’s electrical system from damage caused by excessive amper- age. Always use the same capacity fuse for replacement. If the electrical system does not func- tion, check for blown fuses. See Figure 39

If you have a recurring problem with blown fuses, have the tractor’s electrical system checked by your Cub Cadet dealer.

GOOD BAD

Figure 39

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualTo the Owner Table of ContentsCalling Service Information Rops Information Plate Recording Model and Serial Number InformationTractor Model Plate Important Safe Operation Practices General OperationSlope Operation Do notSafety Frame Rops Warni NG Safety Labels Controls and Features Floorboard and Dash Panel Mounted ControlsPTO Switch Ignition SwitchSeat Adjustment Lever Steering WheelHazard Light Switch Headlight SwitchDifferential Lock Pedal Parking Brake LeverBattery Indicator Light Oil Pressure IndicatorPTO Engaged Indicator Brake Engaged IndicatorFender Mounted Conrtols and Features PTO Reverse Override SwitchFuel Fill Cap PTO Selection LeverTransmission Hi/Lo Range Shift Lever Cup HolderHand Holds Amber Hazard LightsFolding the Rops OperationRollover Protective Structure Rops Fueling the Tractor Safety Interlock SystemNEW Tractor BREAK-IN Procedures Using Jumper Cables to Start Engine Starting the EngineCold Weather Starting Stopping the EngineUsing the FORWARD/REVERSE Pedal Driving the TractorDriving on Slopes Stopping the TractorLOW Using the HI/LO Range Shift LeverUsing the Differential Lock Pedal Engaging the PTO Using the Hydraulic Lift LeverUsing the PTO Selection Lever Using the PTO Reverse Override Switch Using the TOP Link Retainer HookHazard Lights LightingUsing the Three Point Hitch Using the Auxiliary Hydraulic ValveUsing the Hitch Plate Using the Auxiliary Hydraulic Control HandleTractor Weighting On Demand Four Wheel DriveAdjustments Adjusting the SeatAdjusting the Seat Belt Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes Adjusting Hydraulic Lift Feedback RODMaintenance General InformationLubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart Accessing the Engine Compartment General Battery InformationBattery Removal Charging the BatteryBattery Maintenance Battery StorageServicing Electrical System Head Light Bulb ReplacementTail LIGHT/HAZARD Light Bulb Replacement Accessing the Lower Dash Panel Area Checking/Replacing FusesElectrical Circuit Relays Right SideHazard Light Flasher Relay Checking TRANSMISSION/HYDRAULIC System OIL LevelInitial Break-In Period Filter Change Changing TRANSMISSION/HYDRAULIC System OILRegularly Scheduled Oil Filter Changes Check Front Axle OilCheck Final Reduction Gear Case Oil Changing Front Axle and Final Reduction Gear Case OILMaintenance of the Rollover Protective Structure Rops Tire MaintenanceLubrication of Main Drive Shaft Lubrication of FWD Drive ShaftTractor Storage Removing the Tractor from StorageChecking Engine OIL Level Cleaning the EngineCleaning RADIATOR/RADIATOR Screen Adding Engine OIL Changing the Engine OIL and FilterChecking Engine Coolant Level Changing the Engine Coolant Changing the AIR CleanerInspection of Cooling System Hoses Changing The Fuel Filter Servicing the Fuel FilterDraining The Fuel Filter Engine Breather Service Fuel Injector Nozzle ServiceSpecifications Power Take-Off General DimensionsHydraulic Lift System BrakesOptional Equipment and Accessories Description Model NumberPage Page Page CUB Cadet LLC Post Office BOX CLEVELAND, Ohio

6284 specifications

The Cub Cadet 6284 is a robust utility tractor known for its versatility and reliability. Designed for both residential and commercial use, it is ideal for tasks such as landscaping, gardening, and light agricultural work. This model stands out in the compact tractor market due to its powerful engine and innovative features that boost productivity and ease of use.

At the heart of the Cub Cadet 6284 lies a powerful 28-horsepower Kohler diesel engine, which provides ample torque for demanding applications. This engine is designed for efficiency and durability, ensuring long-lasting performance and reduced operating costs. The liquid-cooled design helps to maintain optimal operating temperatures, extended engine life, and consistent power output, making it suitable for various weather conditions.

One of the key characteristics of the 6284 is its hydrostatic transmission, which offers seamless shifting without the need for clutching. This feature allows operators to maintain a steady pace while maneuvering in tight spaces or during intricate tasks. The intuitive controls enhance user experience, making it an excellent choice for both seasoned operators and newcomers alike.

The 6284 features a heavy-duty, rear-mounted three-point hitch with a standard lift capacity which enables the attachment of various implements, enhancing its versatility. With a variety of compatible attachments, including rotary cutters, plows, and loaders, users can easily switch between tasks, making it a multifunctional workhorse.

Another notable technology integrated into the Cub Cadet 6284 is the ergonomic operator station. The layout is designed with user comfort in mind, featuring an adjustable seat, easy-to-reach controls, and excellent visibility, allowing operators to work efficiently for extended periods. The compact design aids in maneuverability, especially in more confined spaces.

Additionally, the Cub Cadet 6284 is built with a sturdy frame and quality materials, designed to withstand heavy use. The all-steel construction contributes to its overall durability, ensuring that the tractor can handle tough jobs without compromising performance.

In summary, the Cub Cadet 6284 is a powerful and efficient compact utility tractor that offers reliable performance for a variety of tasks. Its combination of a robust engine, hydrostatic transmission, and ergonomic design makes it a valuable addition to any toolkit. Whether for residential gardening or more extensive commercial applications, the 6284 is equipped to tackle the job with ease and efficiency.
Top Page Image Contents