Zenoah PSJ2300 owner manual SE1 SE2 SE3 SE4, SE5

Page 13

 

English

 

中 文

 

 

5. Set up

5 安装

 

 

 

 

 

SE1

SE2

SE3

SE4

MOUNTING ENGINE (SE1)

1.Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears.

2.Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the both housings and install the screw.

3.Fasten the clamp securely with 2 screws.

CONNECTING THROTTLE WIRE

1. Remove the air cleaner cover.

2. Connect the end of the throttle wire to the joint on the top of the carburetor. (SE2)

CONNECTING SWITCH WIRES (SE3)

Connect the switch wires between the engine and the main unit.

Fix the switch wire like figure of SE3.

The space between a tank and switch wires is 3mm or more.

(1) 3mm or more

INSTALLING HANDLE (SE4)

Install the handle to the shaft tube and clamp it at a location that is comfortable to you.

(1) About 48cm

安装引擎(SE1

1.将驱动轴罩推向离合器罩,并用手旋 转以检查驱动轴是否与齿轮啮合。

2.将驱动轴罩插入离合器罩直至底部, 然后使两个罩上的定位孔对齐,装上 螺钉。

3.2个螺钉紧固夹具。

连接加油线

1.拆下空气滤清器的盖子。

2.将加油线的一端连接至化油器顶部 的接头上。(SE2

连接开关线(SE3

・连接引擎和主机之间的开关线。 ・如图SE3所示固定开关线。

・燃料箱和开关线之间的距离应为 3mm或以上。

13mm或以上

安装把手(SE4

・将把手安装到轴管并夹紧在您觉得适 合的位置。

1)约48cm

SE5

(1)

JOINT ATTACHMENT (SE5)

Insert the attachment to the main shaft.

Tighten the knob bolt securely.

(1) Knob bolt

接头连接(SE5

・将接头插入主轴。 ・坚固旋钮螺栓。

1)旋钮螺栓

13

Image 13
Contents PSJ2300 Contents Choke lever 11. 进气杆 Air cleaner cover Stop switchLoop handle Suspension point警告标签及用法 Working Condition 正确使用须知Working Circumstance Using the ProductWorking Plan Before Starting Engine Starting the Engine If Someone Comes MaintenanceRefill after cooling the engine Handling FuelTransportation Beware of pinching Kickback and Pinching Safety Precautions Beware of kickbackManufacturer SE5 SE1 SE2 SE3 SE4SE7 SE6SE8 Attaching the Pruning Mechanism SE6Balance Unit SE9Chain OIL 燃料和链条油Starting Engine OP1 OP2 OP3 OP4 OP5Cutting head will start rotating upon the engine starts Fuel Chain oilOP6 Adjusting OIL Flow RateStopping Engine OP4 Checking OIL SupplyOP7 Adjusting Throttle CableOP8 Idle adjusting screw Adjusting Idling Speed OP9OP9 Maintenance Chart MaintenanceMA2 MA1MA3 MA4 MA5 SAW Chain MA6 MA7 MA8Chain type 90SG File size 32 in 4.0mm MA9 Intake air cooling vent back Intake AIR Cooling VentMaintenace Before Storage Procedures to be Performed After Every 100 Hours of USECheck Probable Causes Action Case 1. Starting failurePSJ2300 Specifications

PSJ2300 specifications

The Zenoah PSJ2300 is a high-performance handheld blower designed for professionals and landscaping enthusiasts who demand reliability and efficiency in their tools. Engineered with advanced technologies, the PSJ2300 stands out in the crowded market of outdoor power equipment, making it a go-to choice for various applications such as clearing debris, leaves, and grass clippings.

One of the main features of the Zenoah PSJ2300 is its powerful 23cc two-stroke engine, which delivers impressive blowing performance while maintaining a relatively lightweight design. This engine strikes a perfect balance between power and fuel efficiency, allowing users to operate the blower for extended periods without frequent refueling. The innovative design also ensures that the engine operates smoothly, reducing vibrations and improving overall user comfort during operation.

The blower's air volume output is a notable characteristic that enhances its performance. The PSJ2300 can achieve an air volume of 700 cubic feet per minute (CFM) at a maximum airspeed of 140 miles per hour (MPH), making it highly effective for tackling even the most stubborn debris. Whether you are dealing with wet leaves or compacted grass, the Zenoah PSJ2300 delivers consistent results.

Another key feature of the PSJ2300 is its ergonomic design. The blower is equipped with an adjustable handle that provides users with the flexibility to find their most comfortable grip. This design consideration reduces operator fatigue, allowing for prolonged use without discomfort. Additionally, the lightweight construction ensures that even extended usage can be completed without straining the user.

The Zenoah PSJ2300 also incorporates advanced anti-vibration technology, further enhancing user experience. The innovative damping system minimizes fatigue during long periods of use, allowing for precise control while reducing stress on the hands and arms. This feature is particularly appreciated by professional landscapers who often rely on this equipment for hours on end.

Maintenance is made simple with the PSJ2300, as it is designed for easy access to essential components. This ease of maintenance contributes to the longevity and reliability of the blower, ensuring that it remains a valuable tool in any landscaping arsenal.

In summary, the Zenoah PSJ2300 is a powerful and efficient handheld blower, featuring a robust two-stroke engine, impressive air volume output, ergonomic design, and user-friendly maintenance. With its blend of performance, comfort, and durability, it proves to be a reliable choice for both professional and residential use, making outdoor cleanup tasks easier and more efficient.