Zenoah PSJ2300 owner manual OP6, Stopping Engine OP4, Checking OIL Supply, Adjusting OIL Flow Rate

Page 18

 

English

 

中 文

 

 

7. Operation

7. 操作

 

 

 

 

 

NOTE

1.When restarting the engine immediately after stopping it, leave the choke open.

2.Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it.

补 充

1.当停止引擎后立即重新启动时，进气 门仍然开通。

2.当进气量过大时，由于燃料过量， 会使引擎难以启动。当多次启动引擎 失败时，请开通进气门并重复抽拉拉 绳，或拆下火星塞使其干燥。

■ STOPPING ENGINE (OP4)

■停止引擎（OP4）

1.

Release the throttle lever and run

1. 松开加油杆并让引擎运转半分钟。

 

the engine for a half minute.

2. 将止动开关切换至“Stop（停

2.

Shift the stop switch to the “Stop”

止）”位置。（OP4）

 

position. (OP4)

 

OP6

IMPORTANT

•Except for an emergency, avoid stopping the engine while pulling the throttle lever.

■CHECKING OIL SUPPLY

•After starting the engine, run the chain at medium speed and see if chain oil is scattered off as shown in the figure. (OP6)

(1) Chain oil

NOTE

The oil reservoir has a capacity sufficient to provide about 40 minutes of cutting time (when set to deliver the minimum flow rate, or about as long as you'll get from a tank of fuel). Be sure to refill the oil tank every time when refueling the saw.

■ADJUSTING OIL FLOW RATE

重 要

・除了紧急情况之外，请避免在拉加油 杆时停止引擎。

■检查机油供给情况

・启动引擎之后，以中速运行链条并查 看链条油是否如图所示分散开来。

（OP6）

（1）链条油

补 充

储油箱有足够的容量可提供约40分钟 的切割时间内所需的链条油（当设为最 小）。每次为链锯加油时请务必也在油 箱中加油。

■调节机油流量

WARNING

Never fill the oil reservoir nor adjust the oiler with the engine running.

IMPORTANT

An increase in bar oil flow rate will speed oil consumption, requiring more frequent checks on the oil reservoir. To ensure sufficient lubrication, It may be necessary to

警 告

切勿在引擎运转时进行加油或调节油壶。

重 要

机油流量的增加会加速机油消耗，需要 更频繁地检查储油箱。为确保有充足的 润滑油，可能需要比燃料箱加油时更为 频繁地检查机油量。

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents PSJ2300 Contents Loop handle Stop switchChoke lever 11. 进气杆 Air cleaner cover Suspension point警告标签及用法 正确使用须知 Working ConditionUsing the Product Working CircumstanceWorking Plan Before Starting Engine Starting the Engine Maintenance If Someone ComesHandling Fuel Refill after cooling the engineTransportation Kickback and Pinching Safety Precautions Beware of kickback Beware of pinchingManufacturer SE1 SE2 SE3 SE4 SE5SE8 SE6SE7 Attaching the Pruning Mechanism SE6SE9 Balance Unit燃料和链条油 Chain OILCutting head will start rotating upon the engine starts OP1 OP2 OP3 OP4 OP5Starting Engine Fuel Chain oilStopping Engine OP4 Adjusting OIL Flow RateOP6 Checking OIL SupplyAdjusting Throttle Cable OP7OP8 Adjusting Idling Speed OP9 Idle adjusting screwOP9 Maintenance Maintenance ChartMA1 MA2MA3 MA4 MA5 MA6 MA7 MA8 SAW ChainChain type 90SG File size 32 in 4.0mm MA9 Intake AIR Cooling Vent Intake air cooling vent backProcedures to be Performed After Every 100 Hours of USE Maintenace Before StorageCase 1. Starting failure Check Probable Causes ActionSpecifications PSJ2300

PSJ2300 specifications

The Zenoah PSJ2300 is a high-performance handheld blower designed for professionals and landscaping enthusiasts who demand reliability and efficiency in their tools. Engineered with advanced technologies, the PSJ2300 stands out in the crowded market of outdoor power equipment, making it a go-to choice for various applications such as clearing debris, leaves, and grass clippings.

One of the main features of the Zenoah PSJ2300 is its powerful 23cc two-stroke engine, which delivers impressive blowing performance while maintaining a relatively lightweight design. This engine strikes a perfect balance between power and fuel efficiency, allowing users to operate the blower for extended periods without frequent refueling. The innovative design also ensures that the engine operates smoothly, reducing vibrations and improving overall user comfort during operation.

The blower's air volume output is a notable characteristic that enhances its performance. The PSJ2300 can achieve an air volume of 700 cubic feet per minute (CFM) at a maximum airspeed of 140 miles per hour (MPH), making it highly effective for tackling even the most stubborn debris. Whether you are dealing with wet leaves or compacted grass, the Zenoah PSJ2300 delivers consistent results.

Another key feature of the PSJ2300 is its ergonomic design. The blower is equipped with an adjustable handle that provides users with the flexibility to find their most comfortable grip. This design consideration reduces operator fatigue, allowing for prolonged use without discomfort. Additionally, the lightweight construction ensures that even extended usage can be completed without straining the user.

The Zenoah PSJ2300 also incorporates advanced anti-vibration technology, further enhancing user experience. The innovative damping system minimizes fatigue during long periods of use, allowing for precise control while reducing stress on the hands and arms. This feature is particularly appreciated by professional landscapers who often rely on this equipment for hours on end.

Maintenance is made simple with the PSJ2300, as it is designed for easy access to essential components. This ease of maintenance contributes to the longevity and reliability of the blower, ensuring that it remains a valuable tool in any landscaping arsenal.

In summary, the Zenoah PSJ2300 is a powerful and efficient handheld blower, featuring a robust two-stroke engine, impressive air volume output, ergonomic design, and user-friendly maintenance. With its blend of performance, comfort, and durability, it proves to be a reliable choice for both professional and residential use, making outdoor cleanup tasks easier and more efficient.
Top Page Image Contents