Zenoah PSJ2300 owner manual OP7, OP8, Adjusting Throttle Cable

Page 19

 

English

 

中 文

 

 

7. Operation

7. 操作

 

 

 

 

 

OP7

check the oil level more frequently than at fuel tank refills.

The guide bar and chain are lubricated automatically by a pump that operates whenever the chain rotates. The pump is set at the factory to deliver a minimum flow rate, but it can be adjusted in the field. A temporary increase in oil flow is often desirable when cutting things like hardwood or wood with a lot of pitch.

Adjust the pump as follows:

1.Stop the engine and make sure the stop switch is in the STOP position.

2.Place the unit on its side with the oil reservoir up. (OP7)

(1)Oil tank

(2)Chain cover

IMPORTANT

The oil flow adjusting screw must be pressed in slightly in order to turn. Failure to do so could damage the pump and screw.

3.With a screwdriver, push in on the oil flow rate adjusting screw and turn in the desired direction (there are three incremental settings):

(a)Clockwise-decrease lubrication.

(b)Counter clockwise-increase lubrication.

(c)Middle

导板和锯链通过锯链旋转时运转的泵自

动进行润滑。该泵在出厂时设定一个最 低流量,但在实际操作中可进行调节。 当切割硬木或有很多树脂的木头等材料 时经常需要临时增大机油流量。

如下所述调节泵:

1.停止引擎,并确保止动开关处于

STOP(停止)位置。

2.将机器侧放,使储油箱朝上。 (OP7

1)油箱 (2)链条盖

重 要

必须轻轻地按下机油流量调节螺钉以使 其转动。否则可能会损坏泵和螺钉。

3.使用螺丝刀,推入机油流量调节螺

钉并以所需方向旋转(有三种增量设 定):

a)顺时针转动螺钉以减少润滑油。 (b)逆时针转动螺钉以增加润滑油。 (c)中间

OP8

 

.04 in

 

(1~2mm)

(1)

ADJUSTING THROTTLE CABLE

• The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. (OP8)

(1) Cable adjuster

调节加油钢丝

・在化油器侧进行测量时,钢丝的正常 行程应为12mm。需要时可通过钢 丝调节器重新进行调节。(OP8

1)钢丝调节器

19

Image 19
Contents PSJ2300 Contents Suspension point Stop switchChoke lever 11. 进气杆 Air cleaner cover Loop handle警告标签及用法 Working Condition 正确使用须知Working Circumstance Using the ProductWorking Plan Before Starting Engine Starting the Engine If Someone Comes MaintenanceRefill after cooling the engine Handling FuelTransportation Beware of pinching Kickback and Pinching Safety Precautions Beware of kickbackManufacturer SE5 SE1 SE2 SE3 SE4Attaching the Pruning Mechanism SE6 SE6SE7 SE8Balance Unit SE9Chain OIL 燃料和链条油Fuel Chain oil OP1 OP2 OP3 OP4 OP5Starting Engine Cutting head will start rotating upon the engine startsChecking OIL Supply Adjusting OIL Flow RateOP6 Stopping Engine OP4OP7 Adjusting Throttle CableOP8 Idle adjusting screw Adjusting Idling Speed OP9OP9 Maintenance Chart MaintenanceMA2 MA1MA3 MA4 MA5 SAW Chain MA6 MA7 MA8Chain type 90SG File size 32 in 4.0mm MA9 Intake air cooling vent back Intake AIR Cooling VentMaintenace Before Storage Procedures to be Performed After Every 100 Hours of USECheck Probable Causes Action Case 1. Starting failurePSJ2300 Specifications

PSJ2300 specifications

The Zenoah PSJ2300 is a high-performance handheld blower designed for professionals and landscaping enthusiasts who demand reliability and efficiency in their tools. Engineered with advanced technologies, the PSJ2300 stands out in the crowded market of outdoor power equipment, making it a go-to choice for various applications such as clearing debris, leaves, and grass clippings.

One of the main features of the Zenoah PSJ2300 is its powerful 23cc two-stroke engine, which delivers impressive blowing performance while maintaining a relatively lightweight design. This engine strikes a perfect balance between power and fuel efficiency, allowing users to operate the blower for extended periods without frequent refueling. The innovative design also ensures that the engine operates smoothly, reducing vibrations and improving overall user comfort during operation.

The blower's air volume output is a notable characteristic that enhances its performance. The PSJ2300 can achieve an air volume of 700 cubic feet per minute (CFM) at a maximum airspeed of 140 miles per hour (MPH), making it highly effective for tackling even the most stubborn debris. Whether you are dealing with wet leaves or compacted grass, the Zenoah PSJ2300 delivers consistent results.

Another key feature of the PSJ2300 is its ergonomic design. The blower is equipped with an adjustable handle that provides users with the flexibility to find their most comfortable grip. This design consideration reduces operator fatigue, allowing for prolonged use without discomfort. Additionally, the lightweight construction ensures that even extended usage can be completed without straining the user.

The Zenoah PSJ2300 also incorporates advanced anti-vibration technology, further enhancing user experience. The innovative damping system minimizes fatigue during long periods of use, allowing for precise control while reducing stress on the hands and arms. This feature is particularly appreciated by professional landscapers who often rely on this equipment for hours on end.

Maintenance is made simple with the PSJ2300, as it is designed for easy access to essential components. This ease of maintenance contributes to the longevity and reliability of the blower, ensuring that it remains a valuable tool in any landscaping arsenal.

In summary, the Zenoah PSJ2300 is a powerful and efficient handheld blower, featuring a robust two-stroke engine, impressive air volume output, ergonomic design, and user-friendly maintenance. With its blend of performance, comfort, and durability, it proves to be a reliable choice for both professional and residential use, making outdoor cleanup tasks easier and more efficient.