Bolens 241 Know Your Tiller, Tine Clutch Control, Rear Wheel with Depth Stake, Handle Knobs

Page 6

4

Operating Your Tiller

WARNING

The tine clutch control is a safety device. Never attempt to bypass its operation.

Use extreme care when handling

Know Your Tiller

Tine

Clutch

Control

Recoil

Starter

Clutch Cable

Handle Knobs

Rear Wheel

with Depth

Stake

Tines

Figure 4-1

gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes, and other sources of ignition.

Keep hands and feet away from the tines. Refer to warning label on the unit.

WARNING: Read, understand, and follow all instructions and warnings posted on the machine and in this manual before operating.

Tine Clutch Control

The clutch control lever is located on the upper handle. Squeezing the lever against the handle engages the tine drive. Release the lever to stop the tines from turning.

Rear Wheel with Depth Stake

The depth stake and wheel are located at the rear of the tiller. Both may be adjusted. Refer to the “Wheel Position” and “Depth Stake” sections for instructions.

Handle Knobs

The handle height may be adjusted. Loosen the knobs and remove the carriage bolts to change the position. Reinstall and tighten the hardware when complete.

Engine Controls

NOTE: See the separate engine manual for additional information and functions of the engine controls.

Throttle Control

The throttle control lever is located on the engine. It controls the engine’s speed and stops the engine.

With the throttle control moved completely to the left, the carburetor is in START or FAST position. Use maximum engine speed for deep tilling.

Move the throttle control lever to the right to reduce engine speed. Throttle control should be at IDLE for transporting the tiller.

Move the throttle all the way to the right to stop the engine.

Primer

The primer, located on the engine, is used to pump gas into the carburetor and aid in starting the engine. Use it to start a cold engine, but do not use it to restart a warm engine after a short shutdown.

Recoil Starter

The recoil starter is located on the engine and is used to manually start the engine.

6

Image 6
Contents Front Tine Tiller Model 772C0814 11/28/2005Table of Contents Finding and Recording Model NumberCustomer Support Training PreparationOperation Maintenance & Storage This manual On the machineAssembly AssemblySqueeze the tine clutch control inward. Insert right Rear Wheel with Depth Stake Know Your TillerTine Clutch Control Handle KnobsStarting Engine Using Your TillerBefore Starting Stopping EngineControlling Speed and Tilling Depth CultivatingHandle Pressure Transporting and Storing the Tiller Depth stake to the highest position, FigureMaking Adjustments Engine AdjustmentTine Width Adjustment Engine Cleaning Tine AreaMaintaining Your Tiller LubricationOff-Season Storage Off-Season StorageTrouble Shooting Problem Cause RemedyPage Parts List Pièces Détachées Part Description RÉF PièceWarranty TWO Year Limited WarrantyFor parts and/or accessories refer to customer support on Page Situation Com.mtdproductsAvenue non Ne dents Les Solution Cause ProblèmeDépannage Surchauffe moteur LeSaison Hors Remisage Très est IlCourroie La de ReplacementEntretien Dents des NettoyageRéglages Utilisation Motoculteur du remisage et TransportProfondeur de guide du Réglage Travail de profondeur la de et vitesse la de ControleMotoculteur Moteur le ArrêterMoteur du Démarrage Motoculteur du Commandes Réglages Et Montage Assemblage’huile à et carburant au quant moteur du Remisage et Entretien Responsabilité VotreFonctionnement PréparationGénéral en Utilisation Matières des Table Vente-après ServiceModèle de numéro le trouver Pour ’utilisation Entretien La voir détachées Pièces’UTILISATION Notice 241 Modèle l’avant à dents à Motoculteurs