Clarke S20E manual How To Correct Problems In The Machine, Cause, Action, Page

Page 14
HOW TO CORRECT PROBLEMS IN THE MACHINE

HOW TO CORRECT PROBLEMS IN THE MACHINE

PROBLEM

CAUSE

ACTION

 

 

 

There is no solution flow.

The solution valve is closed.

Open the solution valve.

 

There is an obstruction in the solution hose

Remove the obstruction from the hose and the

 

or filter.

filter.

 

The solution valve or electric wiring is

Repair or replace the valve and the electric

 

damaged.

wiring.

 

The solution tank is empty.

Fill the solution tank.

 

The solution module is damaged.

Check solution module

 

 

 

The solution flow does not stop.

The solution valve is open or dirty.

Close or Clean the solution valve.

 

The solution valve or wiring is damaged.

Repair or replace the valve and the wiring.

 

The solution valve is dirty

Clean the solution valve.

 

There is a damaged seat and washer in the

Replace the seat and washer.

 

solution valve.

 

 

The solution module is damaged.

Check solution module.

 

 

 

The machine does not remove all the

The squeegee is up

Lower the squeegee.

water from the floor.

 

 

 

The squeegee tilt is not correct.

(See Figure 11, page 23)

 

The vacuum tank is full.

Drain the tank.

 

The screen filter is dirty.

Clean the screen filter.

 

There is an obstruction or damage in the

Remove the obstruction or repair the damage.

 

squeegee, squeegee hose or standpipe.

 

 

The vacuum motor is not running.

Check for tripped breaker. Have an autho-

 

 

rized service person make repairs.

 

The squeegee hose is disconnected, or

Check and connect hose.

 

damaged

 

 

The squeegee blade is damaged, worn, or

Turn or replace the squeegee blade.

 

incorrectly installed.

Correctly install the squeegee blade.

 

The squeegee pressure is not correctly

Adjust the pressure of the squeegee.

 

adjusted.

 

 

The gaskets on the cover of the recovery

Replace the gaskets.

 

tank are damaged.

 

 

The recovery tank lid is on wrong.

Rotate lid 180° and replace.

 

 

 

Page -14-

CLARKE TECHNOLOGY Operator's Manual -Encore S20E

Image 14
Contents Operators Manual READ THIS BOOKENCORE S20E Table of Contents OPERATOR SAFETY INSTRUCTIONS AVERTISSEMENTADVERTENCIA WARNING: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs must be performed by authorized Clarke Technology personnel only SPECIFICATIONS Introduction & Machine SpecificationsIntroduction & Machine Specifications Procedures For Transporting Procedures For Transpoting cont How to Remove the Machine From a Van or TruckDD E A BC FG Figure Machine Control PanelFigure Figure 4a Figure 4b Machine Controls and FeaturesFigure How To Remove The Brush or Pad Driver How To Prepare the Machine For OperationHow To Install The Brush Or Pad Driver Figure 5a Figure 5b Figure 5cHow To Operate The Machine Operating The Machine How To Clean A FloorHow To Clean A Very Dirty Floor FigureS20E Parts and Service ManualENCORE SectionCAUSE HOW TO CORRECT PROBLEMS IN THE MACHINEPROBLEM ACTIONACTION PROBLEMCAUSE MAINTENANCE MAINTENANCE Do These Procedures When You End Your Work Figure Figure Figure FigureAdjusting Squeegee Pressure Maintenance For The SqueegeeHow To Adjust The Squeegee Figure Figure 7 Figure Figure88Figure Figure How To Adjust The Squeegee contFigure 115 Volt AccessoriesAccessories 230 VoltCustomer Service - Technical Service - U. S. A. LocationsEuropean Locations SERVICE FACILITIESCLARKE TECHNOLOGY POLYDUR TANK CLARKE TECHNOLOGY U.S. WARRANTYEIGHT YEAR U.S. GUARANTEE CLARKE TECHNOLOGY