Briggs & Stratton 206405GS manual Assembly, Unpack Generator, Shipment Contents, Install Wheel Kit

Page 7

Assembly

Read entire operator’s manual before you attempt to assemble or operate your new generator.

Your generator requires some assembly and is ready for use after it has been properly serviced with the recommended fuel and oil level is verified.

If you have any problems with the assembly of your generator, please call the generator helpline at 1-800-743-4115. If calling for assistance, please have the model, revision, and serial number from the identification label available. See Generator Controls and Features for identification label location.

Unpack Generator

1.Set the carton on a rigid, flat surface.

2.Remove everything from carton except generator.

3.Open carton completely by cutting each corner from top to bottom.

4.Leave generator on carton to install wheel kit.

Shipment Contents

The generator is supplied with:

•Operator’s manual

•Battery float charger

•Wheel kit

Install Wheel Kit

NOTE: Wheel kit is not intended for over-the-road use. You will need the following tools to install these components:

•13 mm wrench

•Socket wrench with a 13 mm socket

•Pliers

•Safety glasses

Install the wheel kit as follows:

1.Tip generator so that engine end is up.

2.Slide axle (A) through both mounting brackets.

3.Slide a wheel (B) over axle.

NOTE: Be sure to install wheel with raised hub inboard.

4.Place a washer (C) on axle and then place an e-ring (D) in axle groove.

CAUTION

E-rings can cause eye injury.

E-rings can spring back and become airborne when installing or removing.

•Always wear eye protection when installing/removing e-rings.

5.Install e-ring with pliers, squeezing from top of e-ring to bottom of axle.

6.Repeat steps 3 through 5 to secure second wheel.

7.Tip generator so that engine side is down.

8.Line up holes in support leg (E) with holes in generator frame.

9.Attach support leg using 2 capscrews (M8 x 20 mm) (F) and 2 hex nuts (G). Tighten with a 13 mm socket wrench and 13 mm wrench.

10.Attach handles (H) to brackets on generator frame as shown, with 45 mm capscrews (J), flat washers (K), nylon washers (L), and M8 lock nuts (M).

NOTE: DO NOT overtighten. Handles must be able to move up and down freely.

11.Return generator to normal operating position (resting on wheels and support leg).

12.Loop handle pins (N) on generator frame just above handle brackets.

13.Raise handles and insert handle pins to move generator.

 

N

 

 

 

L

 

 

J

 

 

 

K

M

 

 

 

 

 

H

 

 

C

 

 

 

 

 

 

A

 

 

F

B

 

 

 

 

 

 

D

 

E

G

 

 

 

 

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operator’s Manual Date Purchased Where to Find UsGenerator EngineTable of Contents Hazard Symbols and Meanings Operator SafetySafety Rules Safety alert symbol is used with a signal wordGenerator produces hazardous voltage Engine exhaust from this product containsBroken bones, fractures, bruises, or sprains could result Contact with muffler area can result in serious burns When Testing for Engine SparkUnintentional sparking can result in fire or electric shock Unpack Generator AssemblyShipment Contents Install Wheel KitVerify Engine Oil Level Attach Negative Battery CableAdd Fuel Special Requirements Connecting to a Building’s Electrical SystemSystem Ground Generator LocationFeatures and Controls 120/240 Volt AC, 30 Amp, Locking Receptacle Battery ChargerCord Sets and Receptacles Nema L14-30Starting the Engine OperationMove fuel valve to Off position Connecting Electrical LoadsStopping the Engine Cold Weather OperationBuilding a Cold Weather Shelter Creating a Temporary Cold Weather ShelterCapacity Select the items you will power at the same timePower Management Don’t Overload GeneratorMaintenance Schedule MaintenanceGenerator Maintenance Adding Engine Oil Engine MaintenanceOil Oil Recommendations Checking Oil LevelService Spark Arrester Service Air CleanerTo service the air cleaner, follow these steps Service Spark PlugCheck Valve Clearance Clean Cooling SystemCarburetor Adjustment Clean and inspect the spark arrester as followsStorage Troubleshooting Owner’s Warranty Responsibilities Emissions Control System WarrantyWarranties Emission Information MaintenanceClaims and Coverage Exclusions Limited Warranty Reserved 800 Product SpecificationsCommon Service Parts AC Load CurrentManual del Operario Fecha de compra Dónde encontrarnosGenerador MotorControles y características Resolución de problemas GarantíasSeguridad de operario MontajeSímbolos de peligro y sus significados Seguridad de operarioDescripción del equipo Reglas de seguridadCuando Transporte O Repare EL Equipo Cuando Anada Combustible O Vacíe EL DepósitoCuando Ponga EN Funcionamiento EL Equipo Cuando Opere EL EquipoCuando Pruebe LA Bujía DEL Motor Cuando Ajuste O Haga Reparaciones a SU Máquina GeneradorEl generador se entrega con MontajeDesembalaje del generador Instale el juego de ruedasComprobar el nivel de aceite del motor Conecte el cable negativo de la bateríaPara instalar Gran altitud Agregue combustibleEl combustible debe reunir los siguientes requisitos Evite el daño del generadorRequisitos Especiales Tierra del sistemaConexión al sistema eléctrico de un edificio Ubicación del generadorAmperios, monofásica de 60 Hz Controles y característicasTomas eléctricas dobles de 120 V CA y 20 a Juegos de cordones y enchufes conectoresCargador de batería Dispositivo de seguridad de 120/240 V, 30 aEncienda el motor OperandoEl motor podría petardear, incendiarse o dañarse Conexión de cargas eléctricasParada del motor Operación durante un clima fríoAdvertencia Control de la energía No sobrecargar el generadorCapacidad EjemploPlan de mantenimiento MantenimientoMantenimiento del generador Adición de aceite del motor Mantenimiento del motorAceite Recomendaciones sobre el aceite Comprobación del nivel de aceiteServicio del bujía Servicio del depurador de aireLimpia B Quite filtro de espuma C y papel el filtro DAjuste del carburador Limpie e inspeccione el apagachispas de la siguiente maneraSistema de refrigeración de aire Comprobación de holgura de la válvulaAlmacenamiento Resolución de problemas Operaciones de mantenimiento que se enumeran en las GarantíasGarantía del sistema de control de emisiones Responsabilidades de la garantía del propietarioInformación sobre emisiones Garantía Limitada Servicio común despide Especificaciones del productoCorriente Carga de C.A

206405GS specifications

The Briggs & Stratton 206405GS is a powerful and reliable small engine designed for a wide range of applications, particularly in lawn care equipment, generators, and various outdoor power tools. Known for its innovative engineering and robust performance, this engine has garnered attention from both commercial and residential users alike.

One of the standout features of the 206405GS is its advanced overhead valve (OHV) design. This configuration enhances fuel efficiency and improves airflow into the combustion chamber, resulting in better overall performance. The engine's ability to deliver higher torque at lower RPMs makes it ideal for tasks requiring consistent power, such as mowing or tilling.

The Briggs & Stratton 206405GS is equipped with a 206cc displacement, offering a potent power output that can handle challenging yard work. With its easy starting mechanism, users can get their equipment up and running with minimal effort. The inclusion of a recoil starter ensures dependability, even in cold weather conditions.

Another notable characteristic of this engine is its durable construction. It features a heavy-duty, cast iron sleeve for added protection and longevity, allowing it to withstand the rigors of outdoor use. Additionally, the engine’s compact size makes it easy to integrate into various machines, facilitating its widespread adoption in the market.

The 206405GS also benefits from Briggs & Stratton’s exclusive technologies such as ReadyStart®. This system eliminates the need for manual priming, allowing for effortless starting every time. The engine’s built-in oil alert system is another important feature that automatically shuts down the engine in the event of low oil levels, protecting the engine from potential damage.

Maintenance is straightforward, with easy access to the air filter and spark plug, aiding in user convenience and minimizing downtime. The engine's fuel system is optimized for minimal maintenance while still delivering adequate power and efficiency.

In summary, the Briggs & Stratton 206405GS is a well-engineered small engine that combines power, efficiency, and durability. With its advanced features and robust performance, it serves as an ideal solution for various outdoor applications, catering to the needs of homeowners and professionals alike. Its reputation for reliability ensures that it continues to be a popular choice in the competitive market of small engines.
Top Page Image Contents