Briggs & Stratton 206405GS manual Operation, Starting the Engine

Page 12

Operation

Starting the Engine

IMPORTANT: Always unplug the battery float charger before starting the generator.

Disconnect all electrical loads from the generator. Use the following start instructions:

1. Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate the unit on a level surface will cause the unit not to start or shut down during operation.

2.Turn the fuel valve to the “On” position. The fuel valve handle should be vertical (pointing toward the ground) for fuel to flow.

3. Push choke lever to “Choke” position ( ).

4. Push engine rocker switch to “On”.

5A. For electric starting, push and hold the start button in start position until generator starts. To prolong the life of starter components, DO NOT hold start switch in start position for more than 15 seconds, and pause for at least 1 minute between starting attempts.

•If engine starts, proceed to step 7.

•If engine fails to start, proceed to step 6.

NOTE: If battery is discharged, use manual starting instructions.

5B. For manual starting, grasp recoil handle and pull slowly until slight resistance is felt. Then pull rapidly one time only to start engine.

WARNING

Starter cord kickback (rapid retraction) can result in bodily injury. Kickback will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains could result.

•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

•NEVER start or stop engine with electrical devices plugged in and turned on.

•If engine starts, proceed to step 7.

•If engine fails to start, proceed to step 6.

6.Move choke lever to “Half” choke position, and pull recoil handle twice.

•If engine fails to start, repeat steps 5 thru 7.

7.Slowly move choke lever to “Run” position ( ). If engine falters, move choke lever to “Half” choke position until engine runs smoothly, and then to “Run” position ( ).

IMPORTANT: If engine floods, place choke lever in “Run” position ( ) and crank until engine starts.

NOTE: If engine starts after 3 pulls but fails to run, or if unit shuts down during operation, make sure unit is on a level surface and check for proper oil level in crankcase. This unit may be equipped with a low oil protection device. If so, oil must be at proper level for engine to start.

WARNING

Contact with muffler area can result in serious burns.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•DO NOT touch hot parts and AVOID hot exhaust gases.

•Allow equipment to cool before touching.

•Keep at least 5 feet (1.5 m) of clearance on all sides of generator including overhead.

•Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

12

BRIGGSandSTRATTON.COM

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s Manual Where to Find Us GeneratorEngine Date PurchasedTable of Contents Operator Safety Safety RulesSafety alert symbol is used with a signal word Hazard Symbols and MeaningsEngine exhaust from this product contains Generator produces hazardous voltageBroken bones, fractures, bruises, or sprains could result When Testing for Engine Spark Contact with muffler area can result in serious burnsUnintentional sparking can result in fire or electric shock Assembly Shipment ContentsInstall Wheel Kit Unpack GeneratorAttach Negative Battery Cable Verify Engine Oil LevelAdd Fuel Connecting to a Building’s Electrical System System GroundGenerator Location Special RequirementsFeatures and Controls Battery Charger Cord Sets and ReceptaclesNema L14-30 120/240 Volt AC, 30 Amp, Locking ReceptacleOperation Starting the EngineConnecting Electrical Loads Stopping the EngineCold Weather Operation Move fuel valve to Off positionCreating a Temporary Cold Weather Shelter Building a Cold Weather ShelterSelect the items you will power at the same time Power ManagementDon’t Overload Generator CapacityMaintenance Maintenance ScheduleGenerator Maintenance Engine Maintenance Oil Oil RecommendationsChecking Oil Level Adding Engine OilService Air Cleaner To service the air cleaner, follow these stepsService Spark Plug Service Spark ArresterClean Cooling System Carburetor AdjustmentClean and inspect the spark arrester as follows Check Valve ClearanceStorage Troubleshooting Emissions Control System Warranty Owner’s Warranty ResponsibilitiesWarranties Maintenance Emission InformationClaims and Coverage Exclusions Limited Warranty Reserved Product Specifications Common Service PartsAC Load Current 800Manual del Operario Dónde encontrarnos GeneradorMotor Fecha de compraResolución de problemas Garantías Seguridad de operarioMontaje Controles y característicasSeguridad de operario Descripción del equipoReglas de seguridad Símbolos de peligro y sus significadosCuando Anada Combustible O Vacíe EL Depósito Cuando Ponga EN Funcionamiento EL EquipoCuando Opere EL Equipo Cuando Transporte O Repare EL EquipoCuando Ajuste O Haga Reparaciones a SU Máquina Generador Cuando Pruebe LA Bujía DEL MotorMontaje Desembalaje del generadorInstale el juego de ruedas El generador se entrega conConecte el cable negativo de la batería Comprobar el nivel de aceite del motorPara instalar Agregue combustible El combustible debe reunir los siguientes requisitosEvite el daño del generador Gran altitudTierra del sistema Conexión al sistema eléctrico de un edificioUbicación del generador Requisitos EspecialesControles y características Amperios, monofásica de 60 HzJuegos de cordones y enchufes conectores Cargador de bateríaDispositivo de seguridad de 120/240 V, 30 a Tomas eléctricas dobles de 120 V CA y 20 aOperando Encienda el motorConexión de cargas eléctricas Parada del motorOperación durante un clima frío El motor podría petardear, incendiarse o dañarseAdvertencia No sobrecargar el generador CapacidadEjemplo Control de la energíaMantenimiento Plan de mantenimientoMantenimiento del generador Mantenimiento del motor Aceite Recomendaciones sobre el aceiteComprobación del nivel de aceite Adición de aceite del motorServicio del depurador de aire Limpia BQuite filtro de espuma C y papel el filtro D Servicio del bujíaLimpie e inspeccione el apagachispas de la siguiente manera Sistema de refrigeración de aireComprobación de holgura de la válvula Ajuste del carburadorAlmacenamiento Resolución de problemas Garantías Garantía del sistema de control de emisionesResponsabilidades de la garantía del propietario Operaciones de mantenimiento que se enumeran en lasInformación sobre emisiones Garantía Limitada Especificaciones del producto Servicio común despideCorriente Carga de C.A

206405GS specifications

The Briggs & Stratton 206405GS is a powerful and reliable small engine designed for a wide range of applications, particularly in lawn care equipment, generators, and various outdoor power tools. Known for its innovative engineering and robust performance, this engine has garnered attention from both commercial and residential users alike.

One of the standout features of the 206405GS is its advanced overhead valve (OHV) design. This configuration enhances fuel efficiency and improves airflow into the combustion chamber, resulting in better overall performance. The engine's ability to deliver higher torque at lower RPMs makes it ideal for tasks requiring consistent power, such as mowing or tilling.

The Briggs & Stratton 206405GS is equipped with a 206cc displacement, offering a potent power output that can handle challenging yard work. With its easy starting mechanism, users can get their equipment up and running with minimal effort. The inclusion of a recoil starter ensures dependability, even in cold weather conditions.

Another notable characteristic of this engine is its durable construction. It features a heavy-duty, cast iron sleeve for added protection and longevity, allowing it to withstand the rigors of outdoor use. Additionally, the engine’s compact size makes it easy to integrate into various machines, facilitating its widespread adoption in the market.

The 206405GS also benefits from Briggs & Stratton’s exclusive technologies such as ReadyStart®. This system eliminates the need for manual priming, allowing for effortless starting every time. The engine’s built-in oil alert system is another important feature that automatically shuts down the engine in the event of low oil levels, protecting the engine from potential damage.

Maintenance is straightforward, with easy access to the air filter and spark plug, aiding in user convenience and minimizing downtime. The engine's fuel system is optimized for minimal maintenance while still delivering adequate power and efficiency.

In summary, the Briggs & Stratton 206405GS is a well-engineered small engine that combines power, efficiency, and durability. With its advanced features and robust performance, it serves as an ideal solution for various outdoor applications, catering to the needs of homeowners and professionals alike. Its reputation for reliability ensures that it continues to be a popular choice in the competitive market of small engines.
Top Page Image Contents