Briggs & Stratton 30228 owner manual Assembly, Remove Generator From Carton, Install Wheel Kit

Page 6

PowerBOSS™

8000W Portable Generator

ASSEMBLY

 

 

 

ASSEMBLY

Your generator requires some assembly and is ready for use after it has been properly serviced with the recommended oil and fuel.

If you have any problems with the assembly of your generator, please call the generator helpline at

1-800-743-4115.If calling for assistance, please have the model, revision, and serial number from the data tag available.

IMPORTANT: Any attempt to run the unit before it has been serviced with the recommended oil will result in an engine failure.

Remove Generator From Carton

1.Set palleted carton on a rigid flat surface.

2.Carefully cut bands around shipping carton.

3.Lift carton off generator.

4.Remove all packing material, carton fillers, etc.

5.Remove generator from shipping pallet.

Install Wheel Kit

The wheel kit is designed to greatly improve the portability of your generator.

NOTE: Wheel kit is not intended for over-the-road use.

You will need a socket wrench with 1/2" or 13mm sockets and a needle-nose plier to install this kit.

Refer to Figure 1 and install the wheel kit as follows:

1.Place generator on a hard flat surface.

2.Stand at control panel end of generator and gently tilt generator up, high enough to place wooden blocks beneath cradle.This will allow you to add wheels.

3.Slide axle through holes in brackets provided on generator cradle.

4.Slide a wheel and flat washer on one end of axle. Make sure air inflation valve is outward. Place e-ring onto groove in axle.

5.Place one end of needle nose pliers on bottom of axle and other end of pliers on top of e-ring. Seat e-ring by pressing pliers closed.

6.Slide axle through until wheel is tight against bracket.

7.Slide a wheel and flat washer on other end of axle. Make sure air inflation valve is outward.

8.Install e-ring on in same manner as steps 4 & 5. Remove wooden blocks.

9.Attach vibration mounts to support leg with 1/4-20 x 1” capscrews and 1/4-20 lock nuts.

10.With wheels on, secure support leg assembly to cradle with M8 x 20 mm long capscrews and lock washers.

Figure 1 — Install Wheel Kit

 

Handle Pin

Nut

Nylon Washers

 

 

 

 

 

 

45 mm Cap Screw

 

 

 

Flat Washers

 

 

 

Handle

 

 

 

Hex Nut

 

 

 

Support Leg

 

Vibration

 

Lock Washer

 

Mount

 

20mm Cap Screw

 

Flat Washer

Axle

1/4-20 x 1”

 

 

Wheel

E-Ring

 

Cap Screw

 

 

 

6

 

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model / Modelo 030228 8000W Table of Contents Safety RulesEquipment Description When Operating Equipment When Adding or Draining FuelWhen Starting Equipment When Transporting or Repairing EquipmentWhen Adjusting or Making Repairs to Your Generator When Testing for Engine SparkKnow Your Generator Assembly Install Wheel KitRemove Generator From Carton Before Starting the Engine Check Battery / Attach Negative Battery WireWhen Adding Fuel Add FuelSystem Ground Using the GeneratorConnecting to a Building’s Electrical System Generator LocationJump Start Procedure Operating GeneratorStarting the Engine Connecting Electrical Loads How to Use the Battery ChargerStopping the Engine Cold Weather Operation Permanent Cold Weather ShelterReceptacles Volt AC, 50 Amp Receptacle120/240 Volt AC, 30 Amp, Locking Receptacle Volt AC, 30 Amp Locking Receptacle Volt AC, 20 Amp, Duplex ReceptaclePower Management DON’T Overload GeneratorCapacity Specifications General Maintenance RecommendationsStorage Generator StorageEngine Storage Other Storage Tips Troubleshooting Problem Cause CorrectionPowerBOSS Limited Warranty Reglas DE Seguridad Conserve Estas Instrucciones Tabla DE ContenidosDescripción DEL Equipo AdvertenciaCuando Opere EL Equipo Cuando Añada Combustible O Vacíe EL DepósitoCuando Ponga EN Funcionamiento EL Equipo Cuando Transporte O Repare EL EquipoPrecaución Cuando Ajuste O Haga Reparaciones a SU GeneradorCuando Pruebe LA Bujía DEL Motor Conozca SU Generador Montaje Para Retirar El Generador De La CajaInstale el Juego de Ruedas Agregue Combustible Antes DE Darle Arranque AL MotorAgregar Aceite al Motor Para instalarConexión al Sistema Eléctrico de un Edificio USO DEL GeneradorTierra del Sistema Ubicación del GeneradorOperando EL Generador Precaución Encienda el MotorParado Del Motor Procedimiento de Arranque en PuenteConexion De Cargas Electricas No Sobrecargue GENERADOR. Vea No Sobrecargue GeneradorOperación Durante UN Clima Frío Cómo al Uso el Corcel de BateríaReceptáculos Precaución Voltios AC, 50 Amperios Receptáculo120/240 Voltios AC, 30 Amperios, Receptáculo de Seguridad Volt AC, 20 Amperios, Receptáculos DoblesTomacorrientes de 120 Voltios AC, 30 Amperios Control de la Energía No Sobrecargue GeneradorCapacidad EjemploEspecificaciones Recomendaciones Generales DE MantenimientoAlmacenando el Motor AlmacenamientoAlmacenando el Generador Otras Sugerencias Para el AlmacenandoDiagnositicos DE Averías Garantía Limitada

30228 specifications

The Briggs & Stratton 30228 is a high-performance generator designed for a variety of residential and commercial applications. Known for its reliability and durability, this portable generator is an excellent choice for anyone in need of backup power during outages or for outdoor activities that require electricity.

One of the standout features of the Briggs & Stratton 30228 is its powerful engine. Equipped with a 479cc OHV (Overhead Valve) engine, it delivers a robust output of 7,500 running watts and up to 9,375 starting watts. This ensures that users can run multiple appliances simultaneously, making it suitable for powering everything from refrigerators and air conditioners to power tools and more.

The generator's design incorporates advanced technologies aimed at maximizing efficiency and usability. One notable feature is its SureStart technology, which ensures easy starting even in low temperatures or after prolonged storage. The automatic idle control feature helps reduce fuel consumption by adjusting the engine speed to match the electrical load, ultimately saving on operational costs and extending run time.

Additionally, the Briggs & Stratton 30228 is built with a heavy-duty steel frame to protect the engine and components from rough handling, ensuring long-lasting performance. Its 7.5-gallon fuel tank provides extended run times, capable of delivering up to 9 hours of continuous power at a 50% load.

The generator features multiple outlets, including four 120V AC outlets, one 120/240V twist-lock outlet for heavy-duty applications, and a circuit breaker for added safety protection. Users will appreciate the ease of transport thanks to its built-in foldable handles and rugged wheels, enabling smooth mobility across various terrains.

Overall, the Briggs & Stratton 30228 combines powerful performance with advanced features and durability, making it an ideal solution for those looking for a reliable power source for emergencies or outdoor activities. Its user-friendly design and efficiency make it a top contender in the portable generator market, appealing to both casual users and professionals alike. Whether for home use or job site applications, this generator proves to be a dependable companion, ensuring that power is just a pull start away.
Top Page Image Contents