MTD Troy-Bilt warranty Drive Belt, Pulley Slot

Page 18

6

Maintaining

Your Snow

Thrower

WARNING

Before lubricating, repairing or inspecting, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop. Remove the safety key to prevent unintended firing of the engine.

IMPORTANT

Refer to the Final Adjustment section of the Set-Up instructions after replacing drive and auger belts.

8.Place a block of wood underneath the auger housing as shown in Figure 6-9 and separate auger housing from the frame by tilting the housing forward and pulling up the handles.

9.Block the impeller with a piece of wood to prevent if from spinning and use a 1/2” wrench to remove the hex screw and washer from the center of the pulley on the auger housing. See Figure 6-10.

10.Lift the brake bracket assembly out of the pulley groove and slide the pulley assembly off the posts of the auger pulley adapter to remove the old belt. Refer to Figure 6-10.

NOTE: The pulley adapter may slide off the auger input shaft when removing the pulley. Use extra caution to ensure the adapter does fall and/or get damaged when removing the pulley.

11.Place the new auger belt in the V-groove of the auger pulley and place the pulley w/belt inside the belt keepers.

12.Turn the pulley as necessary to align its three slots approximately with the posts of the pulley adapter, then move the brake bracket assembly away from the input shaft. While aligning the pulley slots and adapter posts, push the auger pulley fully onto the adapter. Refer to Figure 6-10.

NOTE: If the pulley adapter was removed with the pulley, align the splines of the pulley adapter and auger input shaft, and push the pulley and adapter onto the input shaft. Refer to Figure 6-10.

13.Slide the washer onto the hex screw removed earlier and apply Loctite 262 to the threads of the hex screw.

14.Insert the hex screw through the pulley assembly and into the threads of the input shaft. Torque the hex screw to 250-325 in./lbs. to secure the auger pulley assembly on the input shaft.

If also replacing the drive belt, proceed to the “Drive Belt” instruction. If not, reassemble by performing the previous steps in the opposite order and manner of removal.

NOTE: Make sure to remove the piece of wood blocking the impeller.

Proper Adjustment: With the auger clutch lever in the disengaged position, the top surface of the new belt should be even with the outside diameter of the pulley.

1.To adjust, disconnect ferrule from brake bracket assembly and thread ferrule in (towards idler) to increase tension on belt, and out to decrease tension. See Figure 6-6.

NOTE: The brake puck must always be firmly seated in the pulley groove when auger control is disengaged.

IMPORTANT: Repeat the “Auger Drive Control Test” from the Assembly section before operating snow thrower.

Figure 6-9

B

Adapter Post

 

C

Pulley Slot

A

Figure 6-10

3

1b

1a

2

Figure 6-11

Drive Belt

1.If not already done, remove auger belt as previous instructed.

a.Pull the idler pulley away from the backside of the drive belt to relieve the tension.

b.Slide the drive belt off the idler pulley. See Figure 6-11. Carefully release the idler pulley.

2.Remove the belt from the bottom drive pulley.

3.Remove the belt from the engine pulley.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Two-Stage Snow Thrower 769-04094 06/10/08Table of Contents Finding and Recording Model NumberCustomer Support Do not use the engine’s electric starter in the rain Safety SymbolsThere are rotating blades inside Your Responsibility Restrict the usePreparation Safe Operation PracticesTraining Your ResponsibilityDo not modify engine Maintenance & StorageOperation Average Useful LifeSetting Up Your Snow Thrower Alternator Lead Lamp Wire Clean-Out Tool Final AdjustmentsDrift Cutters If Equipped Tire Pressure Pneumatic Tires Check the adjustment of the auger control as followsSkid Shoes Auger ControlOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 To Engage Drive Gas & Oil Fill-UpStopping The Engine To Engage AugersGeneral Recommendations Always observe safety rules when performing any maintenanceOperating Tips If possible, remove snow immediately after it fallsShift Rod AdjustmentsMaking Drive ControlSee Figure Adjust skid shoes as follows Chute AssemblyChute Bracket Adjustment Auger ControlMaintaining Your Snow Thrower LubricationReplacing Belts Auger Belt Remove LoosenDrive Belt Pulley SlotSecure with the cupped washer and hex bolt removed earlier Using a 3/4 wrench, hold the hex shaftChanging Friction Wheel Rubber Friction WheelOff-Season Storage Trouble Shooting Problem Cause RemedyWarranty 12.08.06For parts and/or accessories refer to customer support on Styles K & L 4554 428Parts List Pièces Détachées Adressez-vous au «Service après-vente»305-342 cc Torque to 21 ft./lbs. maximum618-04514 Worm Gear Box Ass’y w/ grease fitting With or without grease fittings Carter d’engrenages moitié CG avec raccord graisseFor parts and/or accessories refer to customer support on 100 101 100Part RÉF Pièce Description 29.08 Description Roue Jante Roulement Soupape dairFor parts and/or accessories refer to customer support on Page Lubrification de et GarantieGarantie la annule ’entretien conseilsSolution Causes Problème DépannageAccompagne qui moteur du d’utilisation notice la dans PropreUse Jours, 30 de plus pendant entreposé être doit moteur le SiEntretien Frottement de Roue’essieu de Moteur du Et commandes lesPoulie la De Fente Tout empêcher pourÉloignez ’enlevezBoulon l’autre retirez Vitesse de ment LubrificationRoues ’engrenageRéglages ’essieu Des l’entraînement de CommandeVitesses de levier du Tige Support deToucher Général d’ordre Recommandations’utilisation Conseils Les de Évitez .65C 150F dépasser’huile et d’essence Pleins Faites NeGoulotte la de dégagement de Outil Goulotte la de direction Roues des d’orientation CommandeGoulotte la de Commande Fonctions 2 àSouffleuse la de Commandes Tiques pneuma Bandages pneus des Pression Support le surGoulotte la de dégagement de Outil 679-390 OEM Modèles les TousSouffleuse de Modèle Pièce CettePartie la que manière de ajusté être peut goulotte la de La Voir .«Réglages» chapitre le Consultez .goulotte la deDents les avec bien s’engrène manivelle la de hélicoïdale Manivelle la de support le est, besoin Si RemarqueGuidon du Montage Goulotte la de InstallationGoulotte la de manivelle la de Montage ’assemblage pour requis ArticlesMoyenne utile vie de Durée Remisage et EntretienResponsabilité Votre Gaz de émissions les concernant AvisVotre PréparationFormation MentSécurité de Symboles Machine la d’utiliserMatières des Table Vente-après ServiceModèle de numéro le trouver Pour ’utilisation La voir détachées PiècesPhases deux neige à Souffleuse Ca.troybilt.www06/10/08
Top Page Image Contents