MTD Troy-Bilt warranty Safety Symbols, There are rotating blades inside

Page 3

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate.

Symbol

Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate.

WARNING— ROTATING BLADES

Keep hands out of inlet and discharge openings while machine is running.

There are rotating blades inside.

WARNING— ROTATING BLADES

Keep hands out of inlet and discharge openings while machine is running.

There are rotating blades inside.

WARNING— ROTATING AUGER

Do not put hands or feet near rotating parts, in the auger/impeller housing or chute assembly. Contact with the rotating parts can amputate hands and feet.

WARNING—THROWN OBJECTS

This machine may pick up and throw and objects which can cause serious personal injury.

WARNING—GASOLINE IS FLAMMABLE

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

WARNING— ELECTRICAL SHOCK

Do not use the engine’s electric starter in the rain.

1

Safety

Symbols

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol, HEED

ITS WARNING!

Your Responsibility Restrict the use

of this power machine to persons who read, understand

and follow the warnings and instructions

in this manual

and on the machine.

3

Image 3

Contents 769-04094 06/10/08 Two-Stage Snow ThrowerTable of Contents Finding and Recording Model NumberCustomer Support Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineSetting Up Your Snow Thrower Alternator Lead Lamp Wire Clean-Out Tool Final AdjustmentsDrift Cutters If Equipped Auger Control Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 To Engage Augers Gas & Oil Fill-UpStopping The Engine To Engage DriveIf possible, remove snow immediately after it falls Always observe safety rules when performing any maintenanceOperating Tips General RecommendationsDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsMaintaining Your Snow Thrower LubricationReplacing Belts Remove Loosen Auger BeltPulley Slot Drive BeltFriction Wheel Using a 3/4 wrench, hold the hex shaftChanging Friction Wheel Rubber Secure with the cupped washer and hex bolt removed earlierOff-Season Storage Problem Cause Remedy Trouble Shooting12.08.06 WarrantyFor parts and/or accessories refer to customer support on 4554 428 Styles K & LAdressez-vous au «Service après-vente» Parts List Pièces DétachéesTorque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Carter d’engrenages moitié CG avec raccord graisse With or without grease fittingsFor parts and/or accessories refer to customer support on 100 100 101Part RÉF Pièce Description Description Roue Jante Roulement Soupape dair 29.08For parts and/or accessories refer to customer support on Page ’entretien conseils GarantieGarantie la annule Lubrification de etDépannage Solution Causes ProblèmeJours, 30 de plus pendant entreposé être doit moteur le Si PropreUse Accompagne qui moteur du d’utilisation notice la dansEntretien Frottement de Roue’essieu de Tout empêcher pour Et commandes lesPoulie la De Fente Moteur duÉloignez ’enlevezBoulon l’autre retirez ’engrenage LubrificationRoues Vitesse de mentRéglages Support de Des l’entraînement de CommandeVitesses de levier du Tige ’essieuLes de Évitez .65C 150F dépasser Général d’ordre Recommandations’utilisation Conseils Toucher’huile et d’essence Pleins Faites NeGoulotte la de dégagement de Outil Fonctions 2 à Roues des d’orientation CommandeGoulotte la de Commande Goulotte la de directionSouffleuse la de Commandes Support le sur Tiques pneuma Bandages pneus des PressionPièce Cette 679-390 OEM Modèles les TousSouffleuse de Modèle Goulotte la de dégagement de OutilManivelle la de support le est, besoin Si Remarque La Voir .«Réglages» chapitre le Consultez .goulotte la deDents les avec bien s’engrène manivelle la de hélicoïdale Partie la que manière de ajusté être peut goulotte la de’assemblage pour requis Articles Goulotte la de InstallationGoulotte la de manivelle la de Montage Guidon du MontageGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de DuréeMent PréparationFormation VotreMachine la d’utiliser Sécurité de Symboles’utilisation La voir détachées Pièces Vente-après ServiceModèle de numéro le trouver Pour Matières des TablePhases deux neige à Souffleuse Ca.troybilt.www06/10/08