MTD Troy-Bilt warranty Alternator Lead Lamp Wire

Page 7

Figure 3-4

Slide chute assembly over chute opening, making sure the flange keepers are beneath lip of chute adapter. The notches should engage with the spiral end of the chute crank. See Figure 3-5.

Secure flange keeper, locknuts and screws previously removed. Tighten all flange keepers and hardware with two 7/16” wrenches. Do not over tighten.

NOTE: If necessary the chute crank support bracket can be adjusted so the spiral on the chute crank fully engages the teeth on the chute assembly. Refer to the Adjustment Section.

If not already attached, slip the cables that run from the handle panel to the discharge chute into the cable guide located on top of the engine. See Figure 3-6.

Wrap the wire from the head lamp down the right handle until the wire can be plugged into the alternator lead wire under the fuel tank. See Figure 3-7.

3

Setting Up

Your Snow

Thrower

Figure 3-5

WARNING

Prior to operating your snow thrower, refer to Auger Control on page 9. Read and follow all instructions carefully and perform all adjustments to verify your unit is operating safely and properly.

Figure 3-6

Alternator Lead

Lamp Wire

Alternator

Lead

NOTE: Wheels are omitted from illustration for clarity.

Figure 3-7

7

Image 7
Contents 769-04094 06/10/08 Two-Stage Snow ThrowerFinding and Recording Model Number Table of ContentsCustomer Support Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineSetting Up Your Snow Thrower Alternator Lead Lamp Wire Final Adjustments Clean-Out ToolDrift Cutters If Equipped Auger Control Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 To Engage Augers Gas & Oil Fill-UpStopping The Engine To Engage DriveIf possible, remove snow immediately after it falls Always observe safety rules when performing any maintenanceOperating Tips General RecommendationsDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsLubrication Maintaining Your Snow ThrowerReplacing Belts Remove Loosen Auger BeltPulley Slot Drive BeltFriction Wheel Using a 3/4 wrench, hold the hex shaftChanging Friction Wheel Rubber Secure with the cupped washer and hex bolt removed earlierOff-Season Storage Problem Cause Remedy Trouble Shooting12.08.06 WarrantyFor parts and/or accessories refer to customer support on 4554 428 Styles K & LAdressez-vous au «Service après-vente» Parts List Pièces DétachéesTorque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Carter d’engrenages moitié CG avec raccord graisse With or without grease fittingsFor parts and/or accessories refer to customer support on 100 100 101Part RÉF Pièce Description Description Roue Jante Roulement Soupape dair 29.08For parts and/or accessories refer to customer support on Page ’entretien conseils GarantieGarantie la annule Lubrification de etDépannage Solution Causes ProblèmeJours, 30 de plus pendant entreposé être doit moteur le Si PropreUse Accompagne qui moteur du d’utilisation notice la dansFrottement de Roue Entretien’essieu de Tout empêcher pour Et commandes lesPoulie la De Fente Moteur du’enlevez ÉloignezBoulon l’autre retirez ’engrenage LubrificationRoues Vitesse de mentRéglages Support de Des l’entraînement de CommandeVitesses de levier du Tige ’essieuLes de Évitez .65C 150F dépasser Général d’ordre Recommandations’utilisation Conseils ToucherFaites Ne ’huile et d’essence PleinsGoulotte la de dégagement de Outil Fonctions 2 à Roues des d’orientation CommandeGoulotte la de Commande Goulotte la de directionSouffleuse la de Commandes Support le sur Tiques pneuma Bandages pneus des PressionPièce Cette 679-390 OEM Modèles les TousSouffleuse de Modèle Goulotte la de dégagement de OutilManivelle la de support le est, besoin Si Remarque La Voir .«Réglages» chapitre le Consultez .goulotte la deDents les avec bien s’engrène manivelle la de hélicoïdale Partie la que manière de ajusté être peut goulotte la de’assemblage pour requis Articles Goulotte la de InstallationGoulotte la de manivelle la de Montage Guidon du MontageGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de DuréeMent PréparationFormation VotreMachine la d’utiliser Sécurité de Symboles’utilisation La voir détachées Pièces Vente-après ServiceModèle de numéro le trouver Pour Matières des TableCa.troybilt.www Phases deux neige à Souffleuse06/10/08