6.(Figure 25) Note the position of the friction wheel (4). The correct distance “A” from the
right side of the friction wheel (4) to the out- side of the motorbox is as follows:
Tire Size | Distance “A” |
12 and 13 inch | |
16 inch |
If the friction wheel (4) is not in the correct position, adjust as follows.
How To Adjust The Friction Wheel
1.(Figure 1) Position the shift speed lever (6) in the lowest forward speed.
2.(Figure 9) Loosen the bolts (1) on the speed control rod (8).
3.(Figure 25) Move the friction wheel (4) to the correct position.
4.(Figure 9) Tighten the bolts (1) on the speed control rod (8).
5.(Figure 23) Install the bottom panel (2).
6.Tighten the bolts (3) on each side of the bot- tom panel (2).
How To Replace The Friction Wheel
If the friction wheel is worn or damaged, the snow thrower will not move forward. The friction wheel must be replaced as follows.
1.(Figure 1) Remove the gas from the gas tank. Stand the snow thrower up on the front end of the auger housing (4).
WARNING: Drain the gasoline out- doors, away from fire or flame.
2.Disconnect the spark plug wire.
3.(Figure 29) Remove the fasteners that se- cure the left wheel (10). Remove the left wheel (10) from the axle (11).
4.Loosen the bolts (3) on each side of the bot- tom panel (2).
5.Remove the bottom panel (2).
6.(Figure 30) Remove the fasteners that se- cure the drive sprocket (12) to the axle (11).
7.Remove the right wheel, axle (11), and drive sprocket (12).
8.(Figure 31) Remove the four bolts (16) that hold the bearings (7) on each side of the hex shaft (8).
9.(Figure 32) Remove the hex shaft (8) and bearings (7).
NOTE: Take special note of the position of the washers (17) .
10.(Figure 27) Remove the three fasteners (4) that hold the friction wheel (5) to the hub
(6).
11.(Figure 27) Remove the friction wheel (5) from the hub (6). Slip the friction wheel (5) off the hex shaft (8).
12.Assemble the new friction wheel (5) onto hub (6) with the fasteners removed earlier.
13.(Figure 32) Install the hex shaft (8) and bearings (7) with the four bolts removed ear- lier.
Make sure the washers (17) are properly installed in the original position. Also, make sure the two washers (13) are prop- erly aligned with the actuator arms (14).
14.Make sure the hex shaft (8) turns freely.
15.(Figure 30) Install the right wheel, axle (11), and drive sprocket (12) with the fasteners removed earlier. Install the chain (15) onto the drive sprocket (12).
16.Check the adjustment of the friction wheel. See “How To Adjust The Friction Wheel” in this section.
17.Make sure the friction wheel and the disc drive plate are free from grease or oil.
18.(Figure 23) Install the bottom panel (2).
19.Tighten the bolts (3) on each side of the bot- tom panel (2).
20.Install the left wheel (10) to the axle (11) with the fasteners removed earlier.
21.Connect the spark plug wire.
How To Replace the Auger Shear Bolt
The augers are secured to the auger shaft with special shear bolts. These shear bolts are de- signed to break and protect the machine if an object becomes lodged in the auger housing. Do not use a harder bolt as the protection pro- vided by the shear bolt will be lost.
WARNING: For safety and to pro- tect the machine, use only original equipment shear bolts.
To replace a broken shear bolt, proceed as fol- lows. Extra shear bolts were provided in the as- sembly parts bag.
1.(Figure 1) Move the stop switch (13) to the stop position. Disengage all controls.
2.Disconnect the spark plug wire. Make sure all moving parts have stopped.
3.(Figure 14) Lubricate the auger shaft Zerk fitting (1), if equipped, with a grease gun.
4.(Figure 26) Align the hole in the auger with the hole in the auger shaft. Install the new shear bolt (2), spacer (3), and locknut (4).
5.Connect the spark plug wire.
How To Prepare The Snow Thrower For Storage
WARNING: Do not remove gasoline while inside a building, near a fire, or while you smoke. Gasoline
fumes can cause an explosion or a fire.
If the snow thrower is to be stored for an ex- tended period, refer to the engine manufactur- er’s operating manual (included with some models) for important maintenance or storage details.
1.Drain the fuel tank.
2.Let the engine run until it is out of gasoline.
3.Never store the snow thrower with fuel in the tank inside a building where ignition sources are present such as hot water and space heaters, clothes dryers, and the like. Allow the engine (motor) to cool before storing in any enclosure.
GB
4.Drain the oil from the warm engine. Fill the engine crankcase with new oil.
5.Remove the spark plug and pour about 15 ml (1/2 oz) of engine oil into the cylinder. Re- place the spark plug and crank slowly to dis- tribute the oil.
6.Thoroughly clean the snow thrower.
7.Lubricate all lubrication points. See the Main- tenance section.
8.Be sure that all nuts, bolts and screws are securely fastened. Inspect all visible moving parts for damage, breakage and wear. Re- place if necessary.
9.Cover the bare metal parts of the blower housing, auger, and the impeller with spray rust preventative lubricant.
10.Put the unit in a building that has good ven- tilation. Store in a clean and dry area, but NOT near a stove, furnace or water heater which uses a pilot light or any device that can create a spark.
11.If the machine must be stored outdoors, block up the snow thrower to be sure the en- tire machine is off the ground.
12.Cover the snow thrower with a suitable pro- tective cover that does not retain moisture. Do not use plastic.
How To Order Replacement Parts
The replacement parts are shown either on the back pages of this Instruction Book or in a separate Parts List Book.
Use only manufacturer’s authorized or approved replacement parts. The letter placed on the end of the part number denotes the type of finish for the part, C for chrome, Z for zinc, a PA for purchased assembly. It is important that you include this when ordering a part. Do not use attachments or accessories not specifically recommended for this unit. In order to obtain proper replacement parts you must supply the model number (see nameplate).
To obtain replacement parts, contact:
BRIGGS AND STRATTON CANADA
Factory Customer Service
1195 Coutneypark Drive East
Mississauga, Ont.
Collect telephone calls will not be accepted.
Replacement parts for the engine, transaxle, or transmission, are available from the manufacturer’s authorized service centre found in the yellow pages of the telephone directory. Also, see the individual engine or transmission warranties to order replacement parts.
When ordering the following information is required:
(1)The Model Number
(2)Serial Number
(3)Part Number
(4)Quantity
12