MTD 769-03247 warranty Safety Labels, in this manual and on the machine

Page 3

Safety Labels

1

Safety Labels

#3

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may

Chute Clean-out

Tool

Achute clean-out tool is fastened to the top of the auger housing with a mounting clip. The tool is designed to clear a chute assembly of ice and snow.

This item is fastened with a cable tie at the factory. Cut the cable tie before operating the snow thrower.

WARNING: Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind handles until all moving parts have stopped before using the clean-out tool to clear the chute assembly.

result in personal injury. When you see this symbol, HEED

ITS WARNING!

Your Responsibility Restrict the use

of this power machine to persons who read, understand

and follow the warnings and instructions

in this manual

and on the machine.

Image 3

Contents CAREFULLY BEFORE OPERATING EQUIPMENT READ SAFETY RULES AND INSTRUCTIONSOPERATOR’S MANUAL Two-Stage Snow ThrowerTable of Contents Finding and Recording Model NumberCustomer Support ITS WARNING Your Responsibility Restrict the use Safety Labelsresult in personal injury. When you see this symbol, HEED in this manual and on the machinePreparation Safe OperationPractices TrainingDo not modify engine Maintenance & StorageSafe Operation Practices OperationLoose Parts Setting Up Your Snow ThrowerItems Required For Assembly Before AssemblyAttaching the Chute Assembly Drift Cutters If Equipped Clean-Out ToolFinal Adjustments Clean-Out ToolTire Pressure Pneumatic Tires Skid ShoesShift Lever Operating Your Snow ThrowerKnow Your Snow Thrower R R1Ignition Key Chute Clean-Out ToolDrive Control / Auger Control Lock Two-Way Chute ControlIf you have a grounded three-prong receptacle, proceed as follows Gas & Oil Fill-UpStarting The Engine Electric Starter on certain modelsGeneral Recommendations To Engage DriveTo Engage Augers Operating TipsMaking Adjustments4. Repeat on the other side of the snow thrower See Figure Adjust skid shoes as follows2. Raise or lower the skid shoe to desired position 3. Retighten the hex nuts loosened earlierWheels Maintaining Your Snow ThrowerDrive and Shifting Mechanism EngineAuger Belt Replacing BeltsB C A Drive BeltRemove hex screw and washer Hex Shaft Friction Wheel Assemblyfriction wheel assembly and hold assembly in position Changing Friction Wheel RubberOff-Season Storage Remedy Trouble ShootingProblem CauseFOUR YEAR SUPREME WARRANTY WarrantyFor parts and/or accessories refer to customer support on page Adressez-vous au «Service après-vente»à la page 2 pour ce qui concerne les pièces et/ou accessoires 9 23 N DE Parts List Pièces détachéesà la page 2 pour ce qui concerne les pièces et/ou accessoires PARTcas dallées gravillonnées 85 Torque to 20-30 in./lbsSerrez à un couple14 de 20-30 po-lb 49 légèrement au-dessus du goudron 24 Réglez-la au maximum enPART PIÈCE PARTN DE DESCRIPTIONFor parts and/or accessories refer to customer support on page 5368 B 4363 100 Tec PIÈCE PARTN DE DESCRIPTIONPIÈCE PARTN DE DESCRIPTIONFor parts and/or accessories refer to customer support on page 2 page on support customer to refer accessories and/or parts For ANS QUATRE DE SUPRÊME GARANTIE Garantiefrottement Problème SolutionDépannage Causessaison hors Remisage AVERTISSEMENTà carburant le Videz gaz 3 Figure d’entretien Régime34 Figure 33 Figure30 Figure d’entraînement CourroieÉloignez courroies les de Remplacementpatins et Lame Rouesvitesse de ment Moteur19 Figure Réglagesplate lame la et sol le entre maximal ment16 Figure d’essieusupport de Ouverturetransmission la embrayer Pour souffleuse la de UtilisationAVERTISSEMENT tarières les embrayer Poursoigneu Suivez .conducteur le blesser d’huile et d’essence Pleinsélectrique démarreur le d’utiliser avant instructions les toutes sementse pièces les toutes que ce jusqu’à tarière la de commande la de /Blocage l’entraînement de Commandegoulotte la dégager de d’essayer avant immobilisées soientR1 R souffleuse la de Commandesmoteur de Commandes 14 Figure13 Figure montage de Instructionstiques pneuma Bandages pneus des Pressionmain la à goulotte la dans montage deInstructions AVERTISSEMENTmontage de Instructions l’assemblage Avant 3 Figure 2 Figure 1 Figuregoulotte la de manivelle la de Montage guidon du Montagemoyenne utile vie de Durée sécurité de ConsignesRemisage et Entretien SYMBOLE! CE ACCOMPAGNE QUI L’AVERTISSEMENT RESPECTEZPréparation sécuritéde Consignes Utilisationest goulotte la de dégagement de outil Un sécurité de Étiquettesvente-après Service modèle de numéro le trouver Pourmatières des Table D’UTILISATION NOTICE phases deux à neige à Souffleuses