MTD 769-03247 warranty Setting Up Your Snow Thrower, Attaching the Chute Assembly

Page 7

Attaching the Chute Assembly

Figure 4

Attaching the Chute Assembly

•Remove locknuts and screws securing one of the flange keepers to the chute assembly. See Figure 4.

•Loosen but do not remove the locknuts and screws on the other two flange keepers.

•Slide chute assembly over chute opening, making sure the flange keepers are beneath lip of chute adapter. The notches should engage with the spiral end of the chute crank. See Figure 5.

•Secure flange keeper, locknuts and screws previously removed. Tighten all flange keepers and hardware with two 7/16” wrenches. Do not over tighten.

NOTE: If necessary the chute crank support bracket can be adjusted so the spiral on the chute crank fully engages the teeth on the chute assembly. Refer to the Adjustment Section.

•If not already attached, slip the cables that run from the handle panel to the discharge chute into the cable guide located on top of the engine. See Figure 6.

3

Setting Up

Your Snow

Thrower

Figure 5

WARNING

Prior to operating your snow thrower, refer to Auger Control on page 9. Read and follow all instructions carefully and perform all adjustments to verify your unit is operating safely and properly.

Figure 6

Image 7

Contents CAREFULLY BEFORE OPERATING EQUIPMENT READ SAFETY RULES AND INSTRUCTIONSOPERATOR’S MANUAL Two-Stage Snow ThrowerFinding and Recording Model Number Table of ContentsCustomer Support ITS WARNING Your Responsibility Restrict the use Safety Labelsresult in personal injury. When you see this symbol, HEED in this manual and on the machinePreparation Safe OperationPractices TrainingDo not modify engine Maintenance & StorageSafe Operation Practices OperationLoose Parts Setting Up Your Snow ThrowerItems Required For Assembly Before AssemblyAttaching the Chute Assembly Drift Cutters If Equipped Clean-Out ToolFinal Adjustments Clean-Out ToolTire Pressure Pneumatic Tires Skid ShoesShift Lever Operating Your Snow ThrowerKnow Your Snow Thrower R R1Ignition Key Chute Clean-Out ToolDrive Control / Auger Control Lock Two-Way Chute ControlIf you have a grounded three-prong receptacle, proceed as follows Gas & Oil Fill-UpStarting The Engine Electric Starter on certain modelsGeneral Recommendations To Engage DriveTo Engage Augers Operating TipsMaking Adjustments4. Repeat on the other side of the snow thrower See Figure Adjust skid shoes as follows2. Raise or lower the skid shoe to desired position 3. Retighten the hex nuts loosened earlierWheels Maintaining Your Snow ThrowerDrive and Shifting Mechanism EngineAuger Belt Replacing BeltsB C A Drive BeltRemove hex screw and washer Hex Shaft Friction Wheel Assemblyfriction wheel assembly and hold assembly in position Changing Friction Wheel RubberOff-Season Storage Remedy Trouble ShootingProblem CauseFOUR YEAR SUPREME WARRANTY WarrantyAdressez-vous au «Service après-vente» For parts and/or accessories refer to customer support on pageà la page 2 pour ce qui concerne les pièces et/ou accessoires 9 23 N DE Parts List Pièces détachéesà la page 2 pour ce qui concerne les pièces et/ou accessoires PARTcas dallées gravillonnées 85 Torque to 20-30 in./lbsSerrez à un couple14 de 20-30 po-lb 49 légèrement au-dessus du goudron 24 Réglez-la au maximum enPART PIÈCE PARTN DE DESCRIPTIONAdressez-vous au «Service après-vente» B 43 536863 100 Tec PIÈCE PARTN DE DESCRIPTIONPIÈCE PARTN DE DESCRIPTIONAdressez-vous au «Service après-vente» 2 page on support customer to refer accessories and/or parts For Garantie ANS QUATRE DE SUPRÊME GARANTIEfrottement Problème SolutionDépannage CausesAVERTISSEMENT saison hors Remisageà carburant le Videz gaz 3 Figure d’entretien Régime34 Figure 33 Figure30 Figure d’entraînement CourroieÉloignez courroies les de Remplacementpatins et Lame Rouesvitesse de ment Moteur19 Figure Réglagesplate lame la et sol le entre maximal ment16 Figure d’essieusupport de Ouverturetransmission la embrayer Pour souffleuse la de UtilisationAVERTISSEMENT tarières les embrayer Poursoigneu Suivez .conducteur le blesser d’huile et d’essence Pleinsélectrique démarreur le d’utiliser avant instructions les toutes sementse pièces les toutes que ce jusqu’à tarière la de commande la de /Blocage l’entraînement de Commandegoulotte la dégager de d’essayer avant immobilisées soientR1 R souffleuse la de Commandesmoteur de Commandes 14 Figure13 Figure montage de Instructionstiques pneuma Bandages pneus des Pressionmain la à goulotte la dans montage deInstructions AVERTISSEMENTmontage de Instructions l’assemblage Avant 3 Figure 2 Figure 1 Figuregoulotte la de manivelle la de Montage guidon du Montagemoyenne utile vie de Durée sécurité de ConsignesRemisage et Entretien SYMBOLE! CE ACCOMPAGNE QUI L’AVERTISSEMENT RESPECTEZPréparation sécuritéde Consignes Utilisationest goulotte la de dégagement de outil Un sécurité de Étiquettesmodèle de numéro le trouver Pour vente-après Servicematières des Table D’UTILISATION NOTICE phases deux à neige à Souffleuses