Sears 247.88852 owner manual Lamp Wiring, Final Adjustments, Trigger Cable, Auger Control

Page 10
Trigger Cable

•Pull on the cable and rotate it around the bottom of the trigger, with the inner cable in the slot, until the cable end can be pushed into the trigger housing and snapped tight. See Figure 12.

Note: When the cable is installed correctly, you should not be able to pull the cable out of the trigger housing.

•Place the right turn trigger in position underneath the right handle. Secure with screw and weld nut from group H of the hardware pack. See Figure 13. You will need a phillips screwdriver for tightening the screw. Repeat on left side.

 

Secure with screw

Weld Nut

 

 

Turn

Slot

Trigger

Trigger

 

 

Cable

Figure 13

•Secure the right turn trigger cable to the right lower handle using cable tie provided in the hardware pack. Make sure not to wrap the drive cable. See Figure 14.

Trigger Cable

Cable Tie

Figure 14

•Secure the left turn trigger cable to the lower handle using the other cable tie. Make sure to route the cable tie below the auger drive cable so that when the trigger cable is secured by the cable tie, the auger drive cable is left outside the cable tie. Trim excess ends from each cable tie.

NOTE: The right side cable tie must be used to keep cable from coming in contact with the moving shift arm from the transmission.

Lamp Wiring

•Wrap the wire from the lamp down the right

handle as shown in Figure 15.

10

 

•Plug wire into the alternator lead wire under the fuel tank. See Figure 15.

Trigger Cable

Handle

Alternator

Lead

Lamp

Wire

Figure 15

IMPORTANT: Assemble your snow thrower, then check the adjustments as instructed and make any final adjustments necessary before operating the unit. Failure to follow the instructions may cause damage to the snow thrower.

Final Adjustments

Auger Control

•To check the adjustment of the auger control, push forward the left hand clutch grip until the rubber bumper is compressed. There should be slack in the clutch cable.

•Release the clutch grip. The cable should be straight. Make certain you can depress the auger control grip against the left handle completely.

•If adjustment is necessary, loosen the hex jam nut and thread the cable in (for less slack) or out (for more slack).

•Recheck the adjustment. Tighten the jam nut against the cable when correct adjustment is reached.

Traction Drive Clutch and Shift Lever

•Tip the snow thrower forward so that it rests on the auger housing.

•Move the shift lever all the way forward to sixth

(6) position.

•With the traction drive lever released, spin the snow thrower wheels by hand. The wheels should turn; however, you may feel some resistance.

•Engage the traction drive clutch grip. The wheels should no longer turn.

•Now release the traction drive clutch grip, and spin the wheels again.

•Move the shift lever back to the fast reverse position, then all the way forward again. There

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 247.888520 Owner’s ManualSnow Thrower 9 Horse Power 26” Two-Stage Wheel DrivePRODUCT SPECIFICATIONS TABLE OF CONTENTSWARRANTY INFORMATION ContentTRAINING SAFE OPERATION PRACTICESSAFETY PREPARATIONMAINTENANCE AND STORAGE YOUR RESPONSIBILITYHARDWARE PACK Removing From Carton ASSEMBLYAttaching Handle Assembly Loose PartsAttaching Chute ASSEMBLYAttaching Chute Crank Crank Bracket Attaching Clutch CablesLower Chute Hex Lock NutAttaching Shift Rod Attaching Turn TriggersTrigger Cable Lamp WiringFinal Adjustments Auger ControlSkid Shoe Skid Shoe Remove these hardware to adjust skid shoeTire Pressure Pneumatic Tires Meets ANSI Safety Standards OPERATIONKnowing Your Snow Thrower To Stop The Snow Thrower Safety Ignition SwitchOperating Controls Before Starting EngineA. Electric Starter To Start EngineStarting Instructions at a glance PushWarm Start Operating Snow ThrowerTo Throw Snow B. Recoil StarterTo avoid possible freeze-up of the starter, follow Operating TipsBefore Stopping Recoil StarterGeneral Recommendations MAINTENANCEMAINTENANCE Customer ResponsibilitiesViscosity Chart Engine MaintenanceFigure 19 Lubrication Chart LubricationChanging Oil Spark PlugChute Assembly SERVICE & ADJUSTMENTSAdjustments Traction Drive ClutchCarburetor ServiceADJUSTMENTS AugersNOTE Make sure that the auger cable is routed in front of the belt PUSHNOTE Use care to avoid pinching the control cable Drive BeltChanging Friction Wheel Rubber CoverCarburetor Note If you placed plastic under the gas cap, be certain to remove itPreparing Snow Thrower OFF-SEASON STORAGEPreparing Engine STORAGEPossible Causes TROUBLE-SHOOTINGTrouble Corrective ActionBelt Shave Plate ACCESSORIESSpark Plug REPAIR PARTS SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODELPARTS LIST Drive Clutch Cable routed below axle and hooked here SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL NOTE For painted parts, please refer to the list of Handle Support Bracket L.H. 5/8 Includes references 58 throughHex B-Tapp Screw # 10-16 x Handle Support Bracket R.H. 5/8SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL SEARS CRAFTSMAN 9.0 H.P. SNOW THROWER MODEL Page Snow Thrower Model Craftsman Engine Model No. 143.999005 for CraftsmanTable continued on next page Recoil Starter CARBURETOR Page Page Page 7084-659-800 1 semana la a días 7 pm, 7 a am 7 de Llame domicilio, a entrega con piezas ordenar Paradomicilio, a reparación de servicio pedir Para 5811-676-800 1 semana la a días 7 día, al horas 24 Llamecorrectora Accion DE LOCALIZACION DE TABLAProblema posible Causasmotor del Preparación TEMPORAIENALMNADECNieve de Expulsor del Preparación usa si carburador el drene No .carburador al llegue34 Figura colocadohaberlo de gasolina, de tapa la de debajo colocado 33 Figurala simétricamente ensamblar importante Es NOTA apropiadofuncionamiento un para fricción de rueda la en goma 32 Figuracontrol propulsora Correacorrea la de frente al encaminado esté de cable el apretar evitar para precavido Sea NOTA23 Figura Service25 Figura 24 FiguraCanaleta La De Conjunto AJUSTES & SERVICEAjustes 21 Figuracomercial Motor del Mantenimiento20 Figura solvente un con lavando y alambre de cepillocliente del Responsabilidades MANTENIMIENCambios De Mecanismo LubricacionArranque de Abreviadas Instrucciones Ruedas La De PresionOperacion De Consejos operación su con familiarizarseMotor El Apagar Como sin cambios de palanca la mueva NUNCA NOTAPropulsor El Enganchar Para 18 Figuraeléctrico Arrancador Motor Del ArranqueAceite Y Gasolina De Llenado Nieve De Expulsor Del DetencionNieve De Expulsor Su Conozca OPERACIONCambios De Palanca Gatillo Del PalancaAjustes de sección la a refiérase detalles, más Para NOTA 16 FiguraDeslizante Zapata la de Ajuste desconectada está bujía la que asegurarseLámpara la de Cableado transmisión la de cambiosFinales Ajustes 15 FiguraGiro De Gatillos Los De Fijacion Cambios De Vara La De Fijaciony velocidad sexta de posición la de fuera cambios Embrague Del Cables Los De Fijacion7 Figura 9 Figura8 Figura 6 Figura3 Figura Canaleta La De FijacionCanaleta La De Manivela La De Fijacion 4 FiguraRequeridas Herramientas ENSAMBLADOMango Del Conjunto Del Fijacion Sueltas PiezasFERRETERIA DE FERRETERIA DE CONJUNTO tiempos dos de Aceite NIEVE DE EXPULSOR DEL ACCESORIOSBujía raspadora Barra gasolina de Recipiénte CorreaSears nieve de expulsor su de segura operación PREPARACION OPERACION DE SEGURAS PRACTICASOPERACION ENTRENAMIENTOCONTENIDO DE TABLA INFORMACIÓN DE GARANTIAProducto Del Especificaciones USA 60179 IL Estates, Hoffman ,.Co And Roebuck Sears Propietario Del ManualFUERZA DE CABALLOS NIEVE DE EXPULSOR 888520.247 Modelo De .No
Top Page Image Contents